How to remove the outer mirror shell of a Polo?

[WalterMarie]

Polo mirror shell removal method: 1. Use a flat-head screwdriver to pry open a gap from the edge of the mirror shell and the mirror base; 2. Press the lower part of the mirror, and the gap at the top of the mirror will become larger; 3. Insert the flat-head screwdriver into the gap between the mirror and the shell, gently pull outward with your hand, and the mirror shell can be removed. Car mirrors are located on both sides of the front of the car and inside the front of the car. They reflect the conditions behind, beside, and below the car, allowing the driver to indirectly see these positions clearly, expanding the driver's field of vision.

[EdwardLynn]

I once disassembled the exterior mirror housing of a Volkswagen Polo, and the entire process requires careful operation to avoid scratching the car body or damaging parts. First, prepare the tools: a small screwdriver and a plastic pry bar or trim removal tool—avoid using metal tools. Locate the mirror's mounting points, usually one or two screws beneath or inside the mirror glass, and gently loosen them with the screwdriver. Then, slowly insert the pry bar into the gap between the housing and the base, prying it open bit by bit to avoid cracking the housing with excessive force. Be mindful of the wiring connected to the mirror motor inside—do not pull forcefully to prevent breakage. Once removed, you can clean or replace the housing. When reassembling, align the clips and press firmly. The whole process takes no more than 30 minutes, but beginners are advised to practice on the right-side mirror first, as it's more ergonomic, and it's best done in warm weather when the adhesive is softer. Finally, don’t forget to test the mirror adjustment function before driving—safety first.

[JaydenLee]

As someone who frequently handles car repairs, here are the steps I take to remove the Polo's exterior rearview mirror housing: First, ensure the car is turned off to prevent electric shock; prepare tools including a Phillips screwdriver and thin plastic sheets or specialized pry tools. Locate the hidden screw positions at the edges of the housing, commonly found at the bottom of the mirror or under the door's inner cover panel, and loosen all screws. Gently insert the pry tool into the gaps, applying even force to pry it open, avoiding the wiring harness. If the housing is tightly secured, using a heat gun to soften the adhesive before prying can help. After removal, check the interior for dust or water stains and clean them to prevent affecting the mirror. When reinstalling, ensure the sealing strip is properly pressed to avoid air or water leaks. Take your time during the entire process, especially if you're a beginner, to prevent housing deformation or glass breakage. If difficulties arise, it's best to visit a repair shop for professional tools to save time and effort.

[SanChloe]

Hey, I recently removed the mirror housing of my Polo by myself, and it was super easy! The first step is to locate the screws—feel for the small cover beneath the mirror glass, pry it open, and you'll see the screws inside. Unscrew them with a screwdriver. Then, use a plastic card or pry tool (available at supermarkets) to slide into the edge of the housing and gently pry it open. Avoid using excessive force to prevent cracking. Be careful not to touch the wiring inside. Once removed, you can replace the housing or paint it for a fresh look. A pro tip: Use a hairdryer to warm up the adhesive beforehand for easier removal. The whole process takes about ten minutes, but wearing gloves is recommended to avoid scratches. After removing the housing, take the chance to clean off any dirt. When reinstalling, align the clips and press firmly, then readjust the mirror angle. Bonus tip: Avoid doing this on rainy days to prevent water damage or short circuits.

[DiMaverick]

With decades of driving experience, I'll teach you how to safely remove the Polo's exterior mirror housing. Step 1: Prepare a screwdriver and plastic pry tool, and first inspect the housing connection points. Unscrew the fixing screws in the mirror glass area; if the screws are hidden under a cover, carefully pry open the cap. When removing the housing, hold the mirror glass steady with your hand to prevent accidental dropping and shattering. Use the pry tool to gradually separate the housing base, being careful not to scratch the car's paint. Avoid excessive pulling on internal wires, and take a photo to remember their positions before disconnecting. After removal, check if the clips are intact, as older models may have fragile clips. When reinstalling, use new double-sided tape for reinforcement to ensure a tight seal against rainwater. The entire process should take no more than 20 minutes, but seniors are advised to try the passenger side first to reduce difficulty. Never rush or force the removal, as damaging parts would be more costly than the effort saved.