How to Remove the Airbag in Volkswagen Passat?

1 Answers
SanCalvin
08/28/25 3:16am
Here is the method to remove the airbag in Passat: 1. Disconnect the battery cable, turn the steering wheel, remove the side covers on both sides of the steering wheel, and unscrew the four fixing bolts on both sides. 2. Pull out the steering shaft completely and gently remove the generator-sensor from the steering wheel interface. 3. Then remove the fixing nut of the steering wheel, take out the nut and flat washer, and remove the steering wheel. Here are some related materials: 1. The airbag sensors are installed on the left, right, and middle of the cabin partition; the middle airbag sensor and the airbag system are installed together with the electronic control device. The airbag assembly mainly consists of the airbag, gas generator, and igniter. 2. The electronic control device is used for data collection and processing, diagnosing the reliability of the airbag, ensuring that the ignition signal is sent in time when the preset value is reached, and ensuring that the ignition is timed correctly to provide sufficient driving current for the gas generator.
Was this review help?
12
3
Share
More Forum Discussions

How to Set One-Touch Window Control?

To set the one-touch window control, press and hold the window button to raise the window until it is fully closed. Then continue holding the button until you hear a "click" sound from the window. Release the button at this point, and the one-touch window control will be activated. The methods to operate one-touch window control are as follows: 1. Short press: The window will automatically lower completely. Short pull: The window will automatically rise completely. 2. Long press: Release the button during the window's descent to stop it. 3. Long pull: Release the button during the window's ascent to stop it. 4. Long press the unlock button on the remote control to automatically lower all four windows. 5. Long press the lock button on the remote control to automatically raise all four windows.
6
1
Share

Reset Maintenance Light for 2017 Lavida

There are 5 steps to reset the maintenance light for the 2017 Lavida: 1. Turn off the ignition switch and stop the engine; 2. Press and hold the right button on the instrument panel; 3. While holding the right button with your left hand, turn on the ignition switch; 4. Keep holding the button with your left hand until entering the reset mode, then release the right button; 5. Release the right button and press to confirm the reset. The maintenance light serves 2 purposes: 1. Record important component information: It records the mileage of some key components, making it easier for automotive maintenance personnel to understand the vehicle's condition; 2. Serves as a reminder: When the maintenance light comes on, it indicates that the vehicle requires maintenance, and the light should be reset after maintenance is completed.
13
1
Share

Can you change lanes when there is a dotted line next to a solid line?

One side is a dotted line and the other side is a solid line. You can change lanes on the dotted line side, but only the dotted line side can cross into the lane with the solid line, and the lane change must be completed within the dotted line segment. If you exceed the end of the dotted line, it is considered driving over the line. Here are some precautions to note when changing lanes on a dotted line: Violation: During peak traffic hours, you must not forcibly change lanes, as this may affect the normal flow of traffic behind you, potentially resulting in points deducted and fines. Additionally, when waiting in line at a traffic light, if there are many vehicles queued up to the dotted line, some drivers may try to squeeze into the adjacent lane if the vehicles there start moving slower. This is also considered a violation. No consecutive lane changes: Even if the road is clear, you cannot change more than two lanes consecutively on a dotted line. Consecutive lane changes are a violation and may result in a 3-point deduction and a fine.
9
0
Share

What is the character at the beginning of license plates in Hubei?

Hubei license plates start with the character 'E'. The license plate codes for various regions in Hubei Province are as follows: E-A represents Wuhan City, E-B represents Huangshi City, E-C represents Shiyan City, E-D represents Jingzhou City, E-E represents Yichang City, E-G represents Ezhou City, E-H represents Jingmen City, E-J represents Huanggang City, E-K represents Xiaogan City, E-M represents Xiantao City, E-N represents Qianjiang City. Introduction to vehicle license plates: 1. License plates are mostly a combination of Chinese characters, letters, and numbers. Generally, the Chinese character represents the province, the letter following the Chinese character represents the prefecture-level city, and the subsequent letter D represents pure electric vehicles, while F represents non-pure electric vehicles. 2. Vehicle license plates are divided into two types: ordinary license plates and new energy license plates. Based on different colors, they can also be categorized into ordinary family vehicles, government department vehicles, military vehicles, and foreign-related vehicles.
15
3
Share

Can a Gecko Crawl Out of a Sealed Car?

Yes, it can crawl out because a car is not 100% sealed. If a gecko enters your car, you can handle it using the following methods: Geckos prefer darkness: Install lights in areas where geckos frequently appear; they generally avoid well-lit areas. Use air fresheners: Spray strong-smelling air fresheners in places where geckos are often seen to drive them away. Camphor oil: Spray camphor oil in the corners of the car and areas where geckos commonly appear to prevent them from entering. Geckos are beneficial insects that help eliminate mosquitoes and other pests, so there's no need to drive them away. Their presence usually indicates a high number of mosquitoes or other insects.
11
0
Share

What to Do If You Easily Mistake the Accelerator for the Brake While Driving?

Here are the methods to avoid mistaking the accelerator for the brake while driving: 1. Keep your heel on the ground and use your toes to press the brake or accelerator. 2. Position your foot at the same level as the brake. 3. Place your heel below the brake. Press the brake straight down, and when pressing the accelerator, keep your heel stationary and tilt your toes to press the accelerator. 4. Keep your foot on the brake instead of the accelerator. In emergencies, you can press down directly to avoid panic and incorrect operations. The positions of the accelerator and brake are as follows: 1. The accelerator is located on the far right. 2. The brake is positioned in the middle. The functions of the accelerator and brake are: 1. The accelerator is the car's speed control device, used to regulate the vehicle's speed. 2. The brake is the device that stops or slows down the vehicle.
18
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.