How to operate the Hongqi H5 automatic transmission?

What to Do After Changing Tires?

After changing tires, it is necessary to perform wheel balancing. Introduction to Wheel Balancing: The concept of wheel balancing is relatively abstract, generally referring to the asymmetric weight distribution generated when the tire is in motion. Specifically, the tire is mounted on a wheel balancing machine, and based on the rim width and rim diameter, the wheel is accelerated to a certain speed. The rotating sensors on the machine detect the unbalanced points on both sides of the wheel, and then adjustments are made to the tire. Function of Wheel Balancing: The main function of wheel balancing is to prevent the tire from bouncing up and down or swaying left and right during high-speed driving. It also prevents the vehicle from experiencing steering wheel vibration and body shaking issues.

9

1

Share

Manual or Machine Replacement of Coolant?

Manual replacement of coolant is more convenient. Manual replacement allows for thorough inspection and replacement. Method for replacing coolant: Before completely replacing the coolant, conduct a comprehensive inspection to check for any signs of leakage or cracks in the pipes, with particular attention to the five-way water pipe. The five-way pipe is named for its five connecting interfaces to various parts, and the coolant flows through the five-way pipe before being distributed to different parts of the car to function. If there is any leakage of coolant in this section, replace the water pipe or re-secure the interface as needed. Drain the old coolant and then flush the liquid channels with clean water. Add clean water to the coolant reservoir, then continue to fill the reservoir with water so that it flows continuously through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. The water initially flowing out of the reservoir will be slightly pinkish; continue adding clean water until clear water flows out. Note: Remember to remove the heater hose and drain the water from the heater core. After about an hour of draining, add the new coolant through the radiator hose, which allows the coolant to flow quickly into the radiator. Then add another bucket of coolant to the coolant reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. At this point, the coolant level will drop slightly as some air is expelled from the cooling system. Add more coolant until the level reaches the "MAXT" mark on the reservoir.

3

2

Share

Do Motorcycles Rust?

Motorcycles can rust, with common rust-prone areas including cylinder walls, exhaust ports, and exhaust pipes. Components like brake drums and chains are also susceptible. Removing Rust from Motorcycle Chrome Parts: While rust affects visual appeal, chrome parts on motorcycles can develop varying degrees of corrosion due to wear or rainwater exposure. Severe cases may result in unsightly rust spots that both mar appearance and damage components. A chrome-friendly rust removal method can effectively address this issue. Dealing with Rusty Motorcycle Chains: Many riders replace severely worn chains outright, but wear typically occurs in only one direction. A chain has four usable orientations - simply remove the connecting pin, reverse the chain's direction, and reinstall it. This effectively restores the chain's functionality like new.

11

4

Share

Does a Car Fuel Tank Need Cleaning?

Car fuel tanks do require cleaning, and regular maintenance is essential. Except during refueling when it's semi-sealed, the fuel tank remains fully enclosed at all other times. However, as a vehicle ages and accumulates mileage, sediment and impurities inside the tank gradually increase. These contaminants inevitably enter the engine through the fuel supply system, potentially causing damage over time. Fuel Tank Cleaning Interval: The tank itself has built-in protective measures for waterproofing and insulation. If the car frequently idles for extended periods, fuel system cleaning may be necessary as early as 30,000 kilometers. Neglecting this could lead to fuel line blockages and excessive tank pressure, causing vehicle instability during driving. Under such high pressure, the tank becomes prone to cracking, which may result in fuel leaks and increased consumption in severe cases. Fuel Tank Cleaning Technique: Use a clean cloth to cover the filler neck during cleaning. Continuously adjust the position and direction of the plastic tube to minimize contact with the fuel level sensor. After 20 minutes of air flushing, drain the gasoline along with suspended impurities. Note that drained fuel must settle for 72 hours before reuse.

4

0

Share

Can motorcycles carry passengers on national highways?

Motorcycles can carry one passenger on national highways. The regulation only prohibits carrying passengers when riding on expressways; on other roads including national highways, carrying passengers is permitted. Two-wheeled motorcycles can carry passengers: However, the rear seat must not carry minors under 12 years old. Sidecar motorcycles: In addition to the driver, the main seat can carry one person, and the fixed sidecar seat can carry one person. Three-wheeled motorcycles with fixed seating: If the total engine displacement does not exceed 250 cubic centimeters, the approved passenger capacity is no more than 2 people; if the total engine displacement exceeds 250 cubic centimeters, the approved passenger capacity is no more than 4 people.

19

3

Share

What Causes the Abnormal Noise When Accelerating?

Reasons for abnormal noise when accelerating: 1. Wear or impurities inside the fuel pump motor; 2. Damaged throttle body or excessive carbon deposits/sludge; 3. Poor lubrication of the accelerator pedal bearing; 4. Damaged clutch release bearing causing incomplete clutch disengagement. The throttle, also known as the air valve or throttle body, refers to the control device regulating engine power. Solutions for abnormal noise when accelerating: 1. Replace the fuel pump; 2. Clean the throttle body and replace its motor; 3. Apply grease to lubricate the bearing; 4. Remove the clutch to replace the release bearing.

8

0

Share

How to operate the Hongqi H5 automatic transmission?

What to Do After Changing Tires?

Manual or Machine Replacement of Coolant?

Do Motorcycles Rust?

Does a Car Fuel Tank Need Cleaning?

Can motorcycles carry passengers on national highways?

What Causes the Abnormal Noise When Accelerating?

What Causes Loud Engine Shaking Noise?

Does a noisy motorcycle clutch mean the clutch plates need to be replaced?

Can Transmission Fluid Be Used as Power Steering Fluid?

Is the order of safety sign colors red-yellow-blue or yellow-red-blue?