How to open the hood of a Volkswagen Santana?

1 Answers
MargaretFitz
07/29/25 10:29pm
To open the hood of a Volkswagen Santana: On the left side of the driver's footwell, there is a long lever. Pulling it will trigger an audible 'click' indicating the hood has released, though it won't fully open at this stage. You'll need to insert your hand into the created gap, locate the internal latch switch above the emblem, and press it to completely lift the hood. The Volkswagen Santana measures 4475mm in length, 1706mm in width, and 1469mm in height, with a wheelbase of 2603mm. It features front-engine, front-wheel-drive layout, powered by an engine delivering maximum power of 82kW and peak torque of 145Nm.
Was this review help?
3
2
Share
More Forum Discussions

Is the Jetta VS5 a Volkswagen?

Jetta VS5 is a car under the Volkswagen brand. Exterior dimensions: The body dimensions are 4419mm in length, 1841mm in width, 1616mm in height, with a wheelbase of 2630mm. It is a compact SUV with excellent overall proportions, smooth lines, sharp headlights, and highly recognizable wheels. Powertrain: It is equipped with a 1.4T turbocharged engine from the EA211 series, delivering a maximum power of 110kW (150PS) and a peak torque of 250Nm. The transmission system is paired with an Aisin 6-speed automatic transmission.
5
0
Share

What causes a BMW X3 to suddenly stall and fail to restart?

Reasons and solutions for a BMW X3 suddenly stalling and failing to restart are as follows: Use of inferior engine oil: During cold starts, factors such as cylinder pressure, engine speed, and temperature make it difficult for inferior engine oil to ignite, resulting in failure to start. It is recommended to use the manufacturer-recommended engine oil or a higher-quality full synthetic oil. Battery depletion: If the voltage during startup is below the minimum required for the engine control unit to operate, the engine computer will not function, preventing startup. In this case, the battery should be recharged or replaced. Starter relay sticking: During startup, if there is only a slight "click" sound and no further response, this is caused by a sticking starter relay. Pressing the tail end of the solenoid to force it forward can reconnect the starter circuit, allowing the engine to start.
11
3
Share

Will the Venucia D60 automatically lock the doors when parked?

Venucia D60 will automatically lock the doors when parked. Venucia D60 auto-lock setup: Press the start button twice after entering the car (do not ignite), then hold the lock button for five seconds until the hazard lights flash twice consecutively, indicating successful auto-lock setup. Auto-lock feature introduction: The auto-lock feature is determined by the vehicle's design configuration. Some car door lock module programs do not include this function, making it unavailable. However, for some aftermarket remote locks, the auto-lock feature can be achieved by connecting a separate additional module to the vehicle's systems, such as gear position or ignition signals.
15
2
Share

What is the center bore distance for BMW 535 wheel hubs?

The center bore distance for BMW 535 wheel hubs is 5x120. Wheel hub bolt pattern: The professional term for wheel hub bolt pattern is Pitch Circle Diameter (PCD), which refers to the diameter of the circle formed by the center of the lug holes. Most wheel hubs typically have either 5 or 4 lug holes, with varying distances between them. This leads to designations like 4X103, 5X114.3, and 5X112. Taking 5X114.3 as an example, it means the wheel hub's PCD is 114.3mm with 5 lug holes. Checking tire wear condition: This includes verifying whether the tires have worn normally down to the wear indicators, and checking for uneven wear patterns. Tires showing severe abnormal wear should be promptly inspected for causes and replaced. Checking for debris between tread patterns: If any debris is present, it's advisable to remove it. Leaving foreign objects embedded in the tread grooves for extended periods can cause damage to the tires.
11
3
Share

Where is the VIN number of the Venucia T70?

The VIN number of the Venucia T70 can be found on the vehicle nameplate located on the front bulkhead of the engine compartment, the left side of the dashboard, or the central pillar of the vehicle. Introduction to VIN: The Vehicle Identification Number (VIN), or chassis number, is a unique 17-character alphanumeric code assigned to each vehicle. It is used to identify the manufacturer, engine, chassis serial number, and other details of the vehicle. Structure of VIN: There are two main formats of Vehicle Identification Numbers. The first is the ISO 3779 standard adopted by the European Union. The second standard is primarily used in North America, which is more stringent than the first, but the two formats remain compatible with each other.
17
4
Share

What Causes Low Idle Speed in a Corolla?

Corolla low idle speed reasons are as follows: Intake manifold or various valve leaks: When air, fuel vapor, or exhaust gases that should not enter the intake manifold get in, it causes the air-fuel mixture to become too rich or too lean, resulting in abnormal engine combustion. When the leak affects only individual cylinders, the engine may experience more severe shaking, particularly impacting cold idle conditions more significantly. Excessive carbon buildup in throttle body and intake passages: Excessive carbon deposits and dirt in the throttle body and surrounding intake passages alter the cross-sectional area of the air passages, making it difficult for the control unit to precisely regulate idle air intake. This leads to an overly rich or lean mixture and abnormal combustion. Common causes include: oil contamination or carbon buildup on the throttle body; oil or carbon deposits in the intake passages around the throttle body; and oil contamination or carbon buildup on the idle speed control stepper motor, duty cycle solenoid valve, or rotary solenoid valve.
1
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.