How to Make Left and Right Turns When Passing an Overpass in Subject 4?

1 Answers
DelAustin
07/29/25 5:18pm
When making a left turn, you should turn on the right turn signal after entering the overpass or underpass. Then, make a right turn into the ramp, and at the other end of the ramp, make another right turn to enter the main road. This way, two consecutive right turns achieve the purpose of one left turn. When making a right turn, you should turn on the right turn signal in advance, make a right turn near the beginning of the overpass, keep right and enter the ramp, and then proceed from the ramp to the main road.
Was this review help?
15
0
Share
More Forum Discussions

What is the difference between Audi S and RS?

The differences between the Audi S series and RS series are as follows: 1. Different models: Audi S stands for Sport, representing the performance version of the Audi family; the RS series is entirely designed, developed, and manufactured by Audi's quattro department and is not produced on the same line as regular Audi models. 2. Different engines: The Audi S is equipped with a 2.9T turbocharged engine; the RS is equipped with a 2.5T inline five-cylinder engine. Here is some relevant information about Audi: 1. Audi is a luxury car brand under Audi AG, a subsidiary of the German Volkswagen Group. 2. Its logo consists of four interlocking rings. 3. Its headquarters is located in Ingolstadt, Germany, and it has subsidiaries in many countries including China.
4
5
Share

Does Car Clay Bar Damage the Paint?

Using car clay bars properly will not damage the paint. However, some low-quality clay bars may harm the paint. If the clay bar leaves marks all over the car during cleaning, it could be due to excessive pressure, insufficient lubrication, a dirty clay bar surface, poor wrapping ability, or large particles on the paint surface. Below is an introduction to using car clay bars without damaging the paint: 1. Car clay bars should be used with water or lubricant. Before cleaning the car body, rinse off surface dust and dirt as much as possible with water. Choose a clay bar of appropriate size, knead it into shape, and evenly spray water or lubricant on the area to be cleaned and the clay bar. Move the clay bar back and forth in an orderly manner over the cleaning area with your hand, avoiding excessive pressure. Once particles or impurities appear on the clay bar surface, handle them promptly by wrapping them inside the clay bar or replacing the clay bar directly, then continue cleaning with a clean side. 2. If scratches accidentally occur during cleaning, they can be covered with wax or polished depending on the situation.
3
3
Share

Is a Temporary Residence Permit Required for Renewing a Driver's License in a Different Location?

Renewing a driver's license in a different location requires providing a temporary residence permit. Required documents for non-local residents include: original and photocopy of ID card, original and photocopy of work residence permit or temporary residence permit, motor vehicle driver's license, and medical examination certificate. If the vehicle is for disabled individuals, an additional physical certificate issued by a provincial-level medical institution is required. Below are relevant details: 1. The renewal must be processed before the driver's license expires. If the license has expired, renewal in a different location is not possible. In such cases, the license can be transferred to the place of residence first, followed by the renewal procedure, and then the application can be completed at the original license issuance location. 2. For renewal in a different location, the vehicle owner needs to present their ID card, driver's license, and a physical certificate issued by a county-level or above medical institution. The renewal process is straightforward—simply bring the required documents and pay the applicable fee to complete the procedure.
12
1
Share

Is the BMW 6 Series GT Going to Be Discontinued?

BMW 6 Series GT has not been discontinued, and this model is currently in production and available for sale. Here are the specific details about the BMW 6 Series GT: 1. Engine. The 2019 BMW 6 Series GT is equipped with a 2.0-liter turbocharged engine across the lineup, delivering 258 horsepower and a maximum torque of 400 Nm. The engine's maximum power is achieved at 5000 to 6500 rpm, and the maximum torque is available from 1550 to 4400 rpm. 2. Transmission. The engine is paired with an 8-speed automatic transmission (8AT). The BMW 6 Series GT offers strong performance, and the 8AT transmission enhances both the responsiveness and smoothness of power delivery. 3. Exterior Design. The exterior design of the BMW 6 Series GT bears some resemblance to the BMW 5 Series GT. The rear of the car features a large fastback shape, which not only provides a larger trunk opening but also gives the rear a fuller and more attractive appearance, combining aesthetics with practicality.
6
3
Share

Must ETC be installed on the windshield?

ETC must be installed in the center of the car's front windshield, directly behind the rearview mirror. Installing ETC on the upper part of the windshield minimizes obstruction of the driver's view while ensuring better recognition by highway toll station equipment. If you prefer not to install it on the glass, place it in an open area where it can still be visible through the windshield. For passenger cars, the ETC installation position is generally in the upper middle part of the front windshield, while for large vehicles like trucks and buses, it is installed in the middle-lower part. The appropriate installation position should be no lower than 1.2 meters and no higher than 2.5 meters, with an installation angle between 30 to 90 degrees. For vehicles with factory-installed or aftermarket explosion-proof film, which may affect microwave signal transmission, ETC should be installed on the microwave window strip. Here are some precautions for installing ETC: 1. Avoid obstructing the view—installing it behind the rearview mirror is ideal: Many car models have windshields with a significant rearward tilt, which can reduce the driver's field of vision. Installing ETC without considering this may increase blind spots. Placing it behind the rearview mirror on the right side helps avoid blocking the view. 2. Ensure it does not interfere with charging: The ETC electronic tag consumes power but generally does not require charging or battery replacement, as it has a built-in solar panel for self-charging. Therefore, avoid installing it on the windshield's blacked-out areas or positions that may block the solar panel. 3. Do not remove it arbitrarily once installed: The adhesive backing includes an anti-tamper rod connected to a switch. Once installed, the windshield presses the rod in. If removed, the rod pops out, triggering the switch and locking the electronic tag, rendering it unusable until unlocked at an ETC service point. This feature prevents multiple vehicles from sharing one device. 4. Usage tips: The ETC transaction sensing range is 8 meters. To avoid paying for the vehicle ahead due to its faulty ETC device, maintain a distance of at least 10 meters. The ETC lane recognizes vehicles at speeds up to 20 km/h—exceeding this may cause read failures. If using a debit card linked to ETC, insufficient balance may also lead to payment failures.
12
2
Share

What is the idle fuel consumption of a car?

Introduction to car idle fuel consumption: For current general vehicles with a displacement of 1.5-1.8 liters, the hourly idle fuel consumption is approximately 1-2 liters. Additionally, if the air conditioning is turned on during summer, the idle fuel consumption will be even higher. The higher the car's displacement, the more fuel it consumes per hour at idle. Below is relevant information about car idle fuel consumption: 1. Idle fuel consumption varies by vehicle model and is also related to displacement. If idling with the air conditioning on, some cars will automatically assess the load and adjust the idle speed and fuel supply accordingly, which is also influenced by factors such as coolant temperature, air intake, and ambient temperature. 2. It is recommended that car owners turn off the engine rather than let it idle for extended periods while waiting. Prolonged idling not only increases fuel consumption but also leads to incomplete fuel combustion, resulting in carbon deposits.
10
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.