How to Initialize the Windows of a Peugeot 307?

[LaJoshua]

The method to initialize the windows of a Peugeot 307 is as follows: Use the window lift switch in the door. First, manually lower the window to the bottom, then continuously hold the window up button to raise the window from the bottom to the top. Be careful not to release the button. After the window reaches the top, keep holding the up button for about 5 seconds before releasing it, then pull the button up once more. Taking the 2013 Peugeot 307 as an example, its body structure is a 5-door, 5-seat hatchback with dimensions of 4249mm in length, 1786mm in width, and 1556mm in height. It has a wheelbase of 2608mm, a fuel tank capacity of 60 liters, a trunk capacity of 433 liters, and a curb weight of 1280kg.

[EmilioLee]

Last time my 307 lost power, the windows also went haywire, and it took me a while to figure out the initialization. First, start the car (make sure it's in the power-on state), locate the corresponding window button, hold the switch upward without releasing, wait for the window to rise to the top and then continue holding for 5 seconds—you should hear a click. Then, press the switch all the way down, wait for the window to fully lower, and continue holding for another 5 seconds until you hear another click. Each of the four windows needs to be initialized separately this way. If the master control for other windows from the driver's seat fails, you'll need to reinitialize the entire car: hold the master switch's upward button for 15 seconds. After completing the process, remember to test the anti-pinch function—try blocking the window with your hand while it's rising to see if it automatically lowers. If it fails, disconnect the negative terminal of the battery for two minutes and try again—this trick works wonders.

[McValentina]

As a former owner of the 307, I can tell you initializing this car requires some finesse. Try this: after powering on, hold the window switch in the upward position until the window reaches the top, then continue holding for six seconds before releasing. Next, press and hold the switch to lower the window completely, counting six seconds again. The key is maintaining pressure at the extreme positions so the system can memorize the travel points. Perform this in a quiet environment - you should hear a relay click as confirmation. If the driver's controls can't operate the passenger window, long-press the triangular button on the driver's panel to reset all windows. Note that the anti-pinch function may be less responsive for two days after initialization, so be extra careful if children are present. If you fail three times, check if the window regulator track is jammed.

[Lisa]

The key operation is to let the vehicle's computer relearn the window travel. Turn on the ignition but don't start the engine, pull and hold the driver's side window switch upward until the window fully closes, then continue holding for over 10 seconds. Press the same switch all the way down and hold for 10 seconds. Repeat this procedure with the corresponding switches for the other three windows. After completing all steps, lock the vehicle and let it sleep for three minutes to activate the settings. It's best to perform this initialization before rainy seasons to prevent window sticking. Last time I did the initialization, the windows actually became slower - turns out it was due to increased resistance from aged rubber seals. Applying track lubricant solved the problem.

[DelErin]

From someone who's gone through initialization three times, here are the secrets: First, the entire vehicle must be powered on (dashboard lights on). Second, each window needs to be initialized separately. Hold the corresponding button to raise the window all the way up for 8 seconds, then lower it all the way down for another 8 seconds—keeping it pressed longer is more reliable. If the passenger window initialization fails, use the driver's switch to control the passenger window separately and repeat the process. Key reminder: Do not repeatedly press the switch during the operation; maintain continuous pressure. After completion, take the car for a short drive, and the system will automatically save the data. Once, I forgot to close the sunroof, causing the initialization to fail. Later, I found out it was due to unstable voltage, and it only succeeded after using a charger to supplement the power.

[BrookeFitz]

Just helped a neighbor with their 307 window issue. Here are the five steps: turn the key to the ON position - hold the single window up button for 6 extra seconds after it reaches the top - hold the single window down button for 6 extra seconds after it reaches the bottom - operate each window independently - perform a full vehicle initialization by holding the master control switch for 15 seconds to raise all windows. The two most common mistakes: releasing the button midway requires restarting; forgetting to test the one-touch up/down feature. It's recommended to test the anti-pinch function by raising and lowering the windows three times consecutively after initialization. For models with aftermarket central locking systems, a BSI reset might be necessary. Last time, my neighbor's car still malfunctioned after initialization, and it turned out to be a deformed window regulator bracket - replacing the part finally solved the issue completely.