···
Log in / Register

How to Drive a Buick Business Automatic Transmission Car?

3 Answers
DelKira
07/30/25 1:10am
Correct starting steps for a Buick business automatic transmission car: 1. Insert the key and turn it to the ON position, then press the brake; 2. Shift to N gear, start the engine, then shift to D gear; 3. Release the handbrake, lift the foot brake, and start moving. This starting method avoids the brief reverse impact on the transmission when passing through R gear after starting the engine in P gear. The GL8 is a business car under the Buick brand, featuring the new-generation Buick wing-shaped chrome grille, with an elegant and grand appearance. The body dimensions are 5219mm in length, 1878mm in width, and 1776mm in height, with a wheelbase of 3088mm. In terms of power, the GL8 is equipped with a 2.5L SIDI all-aluminum intelligent direct injection engine featuring dual VVT and in-cylinder direct injection technology, delivering a maximum power of 147kW and a maximum torque of 253Nm, paired with a 6-speed DSS intelligent automatic transmission.
Was this review help?
18
2
Share
ReedLee
08/15/25 6:44am
Driving a Buick business automatic is actually quite simple, let me show you how to get started. First, sit in the driver's seat, adjust the seat and rearview mirrors, and fasten your seatbelt. Press the brake pedal to start the vehicle, and the dashboard will light up. Then, hold the gear shift and move it from P to D, release the handbrake, and gently press the accelerator to move. Remember that the Buick business van has a high chassis and a long body, so you need to turn the steering wheel more when making turns, and it's best to use the 360-degree camera when reversing. It's quite stable at 120 km/h on the highway, and the transmission will automatically downshift when you press the accelerator deeply to overtake. When parking, make sure to press the brake firmly and shift back to P, otherwise, the car may roll. The power is a bit weaker when the car is fully loaded, so you need to press the accelerator half a second earlier.
Was this review help?
7
1
Share
Expand All
RhettDella
10/20/25 5:36am
Here are a few key details to note when driving a Buick business MPV with automatic transmission. After starting the engine, don't rush to drive off—let it idle for half a minute to warm up. When shifting gears, wait until the vehicle comes to a complete stop before changing. Due to the higher center of gravity in MPVs, avoid taking turns at speeds exceeding 40 km/h to prevent instability. On long descents, don't rely solely on D mode—switch to L gear or manual mode to utilize engine braking. Using air conditioning affects power output; starting the vehicle five minutes early in summer to cool it down can save fuel. Regularly check the transmission fluid, as sudden stops and starts are most damaging to automatic transmissions. The vehicle automatically locks when the key is more than three meters away, so don't leave it by the fuel pump when refueling.
Was this review help?
20
5
Share
Expand All
More Forum Discussions

What procedures are required for inspecting a gas cylinder?

Inspecting a gas cylinder requires the gas cylinder usage registration certificate from the oil-to-gas conversion, the gas cylinder factory qualification certificate, the gas cylinder installation supervision inspection certificate, the vehicle's driving license, and the owner's ID card. Below is relevant information about the gas cylinder: 1. Function of the gas cylinder: When the rotor and lubricating oil rotate, suction is generated to draw out the internal pressure air produced during braking in the booster, which then returns to the oil reservoir along with the lubricating oil through the oil return line. The lubricating oil settles, and the air is discharged through the exhaust hole on the upper cover, improving the safety performance of the braking system. 2. Materials required for the annual inspection of the gas cylinder: For the gas cylinder inspection, the following materials need to be prepared: one copy of the "Motor Vehicle Registration Certificate," one copy of the "Vehicle Driving License," one copy of the "Gas Cylinder Usage Registration Certificate," and the "Gas Cylinder Qualification Certificate."
7
3
Share

Where are the sensors located on the Nissan Teana?

Nissan Teana sensors are located in the following positions: 1. Oxygen Sensor: The oxygen sensor is installed on the exhaust pipe to monitor the post-combustion gases and determine whether the engine combustion is sufficient and whether the mixture is too lean or too rich. 2. Wheel Speed Sensor: It primarily collects the vehicle's speed to detect any signs of wheel slippage. Therefore, there is a dedicated sensor to gather wheel speed data, usually installed on the hub of each wheel. If the sensor fails, the ABS system will become ineffective. 3. Coolant Temperature Sensor: The coolant temperature sensor is typically located near the thermostat. It converts the coolant temperature into an electrical signal, increasing fuel injection or advancing the ignition timing at low temperatures, while preventing detonation and retarding the ignition timing at high temperatures. 4. Intake Pressure Sensor: Generally installed near the throttle body, the intake pressure sensor detects changes in resistance and pressure corresponding to different engine speeds and loads, converting these into voltage signals for the ECU to adjust fuel injection and ignition timing.
2
3
Share

How to Replace the Wiper Blades on a Lavida?

The method for replacing the wiper blades on a Lavida is as follows: 1. After turning off the vehicle, do not remove the key immediately. Within 3 seconds, pull the wiper control lever inward, and the wipers will move to the maintenance position. 2. Gently pull the wiper arm toward the front of the vehicle until it locks into place. Press the silver button on the wiper arm, hold the wiper blade, and pull it outward with slight force to remove the old rubber blade. 3. Release the two clips and remove the old rubber blade. 4. When installing the new rubber blade, remember to stagger the two metal pieces and ensure it is inserted into the first groove. The process is slightly tedious and requires patience; install one side first before proceeding to the other. 5. After successful installation, follow the reverse order of the removal steps to complete the wiper blade installation.
20
1
Share

How Hard is Carbon Fiber?

Carbon fiber material is an ultra-hard substance that is 10 times harder than ordinary steel, second only to the hardness of diamond. Below is a relevant introduction to carbon fiber: 1. Composition of Carbon Fiber: Carbon fiber is formed by stacking organic polymer fibers with extremely high carbon content along the fiber bundle direction. The currently recognized high hardness and ultra-strong shear resistance are not entirely due to material properties. There is a decisive factor involved—the critical void. When the stacking between fibers is below a certain critical value, the void index between fibers determines the hardness, shear resistance, and tensile strength of the fiber. 2. Reasons for Hardness Reduction: The critical porosity that causes a decline in material mechanical properties is 1%–4%. When the void volume content is within the range of 0–4%, for every 1% increase in void volume content, the interlaminar shear strength decreases by approximately 7%. Moreover, higher porosity leads to larger void sizes, significantly reducing the area of interlaminar interfaces in the laminate. When the material is under stress, it is prone to failure along the layers, which is why interlaminar shear strength is relatively sensitive to porosity.
8
4
Share

Are Passat Seat Heating and Seat Ventilation the Same?

Passat seat heating and seat ventilation are not the same functions. Seat heating refers to the electric heating device inside the seat. Seat ventilation is the "summer cooling device" of the car seat air conditioning, which is divided into air supply type and air suction type. More details are as follows: 1. The car seat air conditioning system includes ventilation circulation, dehumidification and cooling/heating, and intelligent temperature control, completely eliminating the discomfort caused by the seat being hot and sticky in summer and cold in winter while driving. 2. As an effective supplement to the car air conditioning system, the car seat air conditioning system can adjust the temperature and humidity of the seat surface, maximizing the satisfaction of different drivers and passengers' requirements for seat surface temperature in different seasons, helping them maintain full energy and clear reaction ability. According to statistics, it can save fuel consumption by an average of 7-9%. 3. The car seat air conditioning system is divided into two types: external and built-in. Seat heating uses electric heating wires inside the seat to heat the seat interior and transfers the heat to the occupant through heat conduction, improving the discomfort caused by the seat being too cold after long periods of parking in winter.
13
2
Share

How to use the GAC GS3 navigation system?

GAC GS3 navigation system usage method is as follows: 1. The GAC GS3 center console panel adopts a snap-on design. For complete removal, a pry bar and a Phillips screwdriver are required. 2. Start prying from the bottom of the center console panel. After prying it open, remove the wiring harness and take out the original radio panel. 3. Install the navigation system by connecting the plugs. If unsure, refer to the car navigation manual for guidance. 4. Install the GPS receiving antenna and the rearview camera. 5. Route the rearview camera wiring harness along the door edge seal to the rear seats, then fold down the rear seats and pass it through to the trunk. 6. Install the rearview camera inside the license plate light, then route the camera wiring harness back and complete the installation. 7. Test for any issues. If everything is normal, reinstall in the reverse order of removal.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.