How to Deal with Stubborn Water Stains on Your Car?

1 Answers
AdelynMarie
07/30/25 12:03am
Use toothpaste to clean the car body. Apply an appropriate amount of toothpaste to the water stains, then gently wipe with a soft towel. Repeat several times and rinse with water. Dishwashing liquid from your kitchen can also effectively remove stubborn water stains. Apply a suitable amount to the stained areas, gently rub with your fingers, and wipe with a dishwashing sponge.
Was this review help?
3
5
Share
More Forum Discussions

How to Replace the Oil Filter on a Verna?

The steps to replace the oil filter on a Verna are as follows: 1. Start the engine and let it reach operating temperature. Use a jack to lift the vehicle, engage the handbrake, and secure the front wheels with wheel chocks. 2. Drain the oil. Locate the oil drain plug underneath the vehicle, unscrew it to allow the oil to flow out. Observe the oil color - normal oil should be translucent; if it appears black, it should be replaced promptly. 3. Remove the oil filter. When the oil flow slows down, unscrew the oil filter for secondary drainage. Removing the filter can be challenging and requires a specialized filter wrench. Allow all residual oil in the compartment to drain completely. 4. After complete drainage, install the new oil filter using the filter wrench and tighten it. Then tighten the drain plug and lower the vehicle. 5. Open the new oil filter package. Apply a moderate amount of new oil on the sealing ring. Wipe clean the mating surface of the filter housing with a clean cloth. Install the new filter and tighten it to proper torque using an oil filter wrench. Clean the exterior and mating surface of the new filter. 6. Reinstall the drain plug, lower the vehicle, and refill with new oil. Check the oil level. Start the engine and let it run at idle and medium speed for a while, meanwhile checking for any oil leaks around the filter. The job is complete when everything functions normally.
3
4
Share

How to Most Accurately Align the Shoulder Line in Subject 2?

First, to align the line correctly, you must adjust to a proper sitting posture. The seat height should ensure that your wrists can just rest on the 12 o'clock position of the steering wheel, which is the most suitable height. During the test, make it a habit to glance at the position of your shoulder with your peripheral vision. When your shoulder is roughly aligned with the standard line, the line can basically be aligned.
2
5
Share

Why does the Sagitar's RPM increase but the speed doesn't rise?

Sagitar's RPM increases but the speed doesn't rise, which may be due to problems with the clutch or transmission, preventing the engine's power from being transmitted to the wheels. Here is an analysis of the reasons why the Sagitar's RPM increases but the speed doesn't rise: 1. The engine's power is first transmitted to the clutch. If the clutch plate is severely worn or the clutch pressure plate spring is damaged, it can cause incomplete power output, resulting in a mismatch between the engine's power and the output power. 2. If the transmission is not engaged in the corresponding gear, for example, the gear lever is in the 5th gear position, but the transmission gears are only engaged in the 2nd gear position, it can also cause the RPM to increase without a corresponding rise in speed. This is commonly referred to as gear misalignment, and such problems are often accompanied by the inability to engage reverse gear. 3. Check if the automatic transmission is faulty: Move the gear selector to different positions and drive the car. If the engine RPM suddenly increases when the automatic transmission shifts to a certain gear, but the speed doesn't increase accordingly, it indicates that the gear is slipping. The more easily the engine RPM increases during slipping, the more severe the slipping is.
13
1
Share

How to Solve the Oil Burning Issue in DS5?

For older vehicles, using engine oil with higher viscosity is also an option. Oil burning refers to the situation where engine oil enters the combustion chamber of the engine. The maintenance cycle of a car is determined based on its normal usage conditions. It is advisable to shorten the maintenance cycle and the prescribed mileage according to the actual situation, and also try to avoid prolonged high-speed driving.
12
1
Share

What are the steps to drive a C1 manual transmission car?

After starting the car, press the clutch pedal all the way down with your left foot to fully disengage the clutch. Shift the transmission into first gear. For most models, first gear is located in the front-left position. The shifting action should be accurate and swift. Depending on the car model, press or lift the electronic parking brake button. Continue pressing the clutch pedal with your left foot and press the accelerator pedal with the tip of your right foot. Once the car starts moving smoothly, you can repeat the process of pressing the clutch, shifting gears, and pressing the accelerator to complete upshifting.
11
3
Share

How to Press the Buttons in Subject Three?

First, walk to the rear seat on the driver's side and press the first button, then proceed to the right rear and press the second button. After that, move forward to the front passenger seat and press the third button. All three buttons are located on the exterior. When pressing the buttons on the car, avoid pressing them too briefly, as the system may deem it invalid. It's best to hold each button for three seconds.
1
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.