How to Deal with a Ford Mondeo That Won't Start?

Do Brake Pads Need to Be Replaced Together Front and Rear?

Brake pads do not need to be replaced together front and rear. They should be replaced when the thickness is less than 0.5cm. Brake pads play a crucial role in braking and are composed of a steel plate, adhesive heat insulation layer, and friction block. The steel plate is coated to prevent rust, and the coating process is monitored using a furnace temperature tracker to ensure quality by detecting temperature distribution. Steps for replacing brake pads: 1. Release the handbrake and loosen the hub screws of the wheel needing replacement. Use a jack to lift the car and remove the tire. 2. Remove the tire to expose the brake caliper and disc. Apply lubricant to loosen the screws or nuts if necessary. 3. Hang the brake caliper with a rope and remove the old brake pads. 4. Open the hood and unscrew the cap of the brake fluid reservoir. 5. Install the new brake pads in the correct position.

4

2

Share

What are the differences between the Audi Q5 and Audi Q5L?

The differences between the Audi Q5 and Audi Q5L lie in their body dimensions: The Audi Q5 measures 4629mm in length, 1898mm in width, and 1655mm in height, with a wheelbase of 2807mm; whereas the Audi Q5L measures 4765mm in length, 1893mm in width, and 1659mm in height, with a wheelbase of 2908mm. Both models are equipped with a 2.0L turbocharged engine, delivering a maximum horsepower of 190PS, a maximum power of 140kW, a maximum power speed range of 4300 to 6000rpm, a maximum torque of 320Nm, and a maximum torque speed range of 1500 to 4200rpm. They are paired with a 7-speed dual-clutch transmission.

1

4

Share

Is the Wuling Hongguang shock absorber universal?

Wuling Hongguang shock absorbers are not universal. More information about shock absorbers is as follows: 1. Shock absorbers are used to suppress the oscillation of the spring after absorbing shock and the impact from the road surface. 2. Shock absorbers are widely used in automobiles to accelerate the attenuation of frame and body vibration, thereby improving the driving smoothness of the vehicle. 3. If the shock absorber is too soft, the body will bounce up and down; if the shock absorber is too hard, it will bring too much resistance, hindering the normal operation of the spring. 4. Hard shock absorbers should be matched with hard springs, and the hardness of the spring is closely related to the weight of the vehicle. Therefore, heavier vehicles generally use harder shock absorbers.

8

5

Share

Can brake pads be replaced at 60,000 kilometers?

Brake pads can be replaced at 60,000 kilometers. Typically, front brake pads need replacement every 30,000 to 50,000 kilometers, while rear brake pads should be replaced every 60,000 to 100,000 kilometers. Below is relevant information about brake pads: 1. Definition: Brake pads generally consist of a steel plate, an adhesive heat insulation layer, and a friction block. The steel plate is coated to prevent rust, with the coating process monitored by an SMT-4 furnace temperature tracker to ensure quality by detecting temperature distribution. The heat insulation layer is made of non-conductive materials to provide thermal insulation. 2. Quality issues: Due to friction, the friction block gradually wears out. Generally, lower-cost brake pads wear out faster. Inferior materials can lead to excessive heat decay and thermal conductivity, resulting in sparks and loud noises during braking, shorter lifespan, approximately 30% longer braking distance, and lack of post-sale guarantees due to untested and rough manufacturing processes.

2

Share

What are the impacts of rear-end collision and subsequent cutting on a vehicle?

A rear-end collision typically has minimal impact on the powertrain and mechanical systems of a vehicle. However, if the main frame is damaged, it could significantly affect the vehicle's safety. Additionally, any vehicle that has undergone sheet metal repair or cutting will experience depreciation, resulting in a substantial price reduction when sold as a used car. Below is additional information: 1. Sheet Metal Work: Sheet metal fabrication is a comprehensive cold-working process for thin metal sheets (usually under 6mm), including shearing, punching, bending, welding, riveting, mold forming, and surface treatment. A notable characteristic is the uniform thickness of the same part. 2. Advantages: Most sheet metal components are made from thin metal sheets and tubes. Due to their lightweight, high strength and rigidity, ability to form complex shapes, low material consumption, and smooth surfaces, they are widely used in daily life and industrial production. The finished products are extensively applied in the bodies of cars and trucks.

17

0

Share

What is the wheelbase of the Focus?

The wheelbase of the Focus is 2705mm. Its body dimensions are: length 4670mm, height 1810mm, width 1468mm. The fuel tank capacity is 53 liters, and the trunk capacity is 511 liters. The drivetrain is front-engine, front-wheel drive, with electric power steering. The front suspension is MacPherson strut independent suspension, and the rear suspension is torsion beam non-independent suspension. The Focus is equipped with a 1.5L naturally aspirated engine, producing a maximum horsepower of 122PS and a maximum power of 90kW at 6000rpm. The maximum torque is 153Nm, available between 1750 to 5000rpm. It is paired with an 8-speed automatic transmission.

12

0

Share

How to Deal with a Ford Mondeo That Won't Start?

Do Brake Pads Need to Be Replaced Together Front and Rear?

What are the differences between the Audi Q5 and Audi Q5L?

Is the Wuling Hongguang shock absorber universal?

Can brake pads be replaced at 60,000 kilometers?

What are the impacts of rear-end collision and subsequent cutting on a vehicle?

What is the wheelbase of the Focus?

How to Fold Down the Seats in a Sagitar?

What does the position light icon look like?

How to Set Cruise Control on Audi A4L?

What is the 0-100 km/h acceleration time of the Haval H4?