How to Clear the Maintenance Reminder on the Lynk & Co 03?

[DiPaul]

To clear the maintenance reminder on the Lynk & Co 03, follow these steps: 1. First, navigate to the remaining maintenance mileage interface on the display, then press and hold the button on the end of the wiper stalk. 2. The screen will show the remaining mileage changing to 5000; continue holding the button until the numbers stop flashing, and the reminder will be cleared. The Lynk & Co 03 features technologies such as three-screen interaction, cloud connectivity, and active and passive safety technologies in its configuration. In terms of interior design, it boasts a wraparound sporty cockpit, a driver-oriented smart integrated center console, race-inspired air vents, a D-shaped sport steering wheel with multifunction buttons, a digital instrument cluster, and an electronic parking brake and driving mode selector knob around the gear lever.

[OEmmett]

I've figured out the maintenance reminder reset process after several attempts. Geely Lynk & Co 03 owners, pay attention to the operational details. First, ensure the vehicle is completely powered off. Then press and hold the TRIP button on the right side of the steering wheel. Next, turn the key to the accessory position without starting the engine - the maintenance icon on the dashboard will begin flashing. Immediately release the button when you see the flashing, then quickly press the TRIP button again for about 5 seconds until the warning light completely disappears. Keep your finger firmly pressed on the button throughout - my first attempt failed because my long nails prevented proper contact. Also, perform this operation when the engine is cold, as the electronic system may respond slower otherwise. If unsuccessful after three consecutive attempts, it might indicate a fuse or ECU issue, in which case visiting a dealership for professional reset is advisable. This procedure works for both new and older 03 models, though hybrid versions require additional pressing of the EV mode switch button.

[LuciaAnn]

After the last maintenance, the 4S shop forgot to reset the reminder for me, but it's actually quite simple to do it yourself. First, completely power off the vehicle, including turning off all electrical devices. Hold down the TRIP button at the bottom right of the dashboard with your left hand and don't let go, then turn the key with your right hand to power up the dashboard. At this point, you'll see the yellow wrench icon start flashing. Quickly release the button and press it again, holding it down until the icon disappears. The key point is that the second press needs to last 3-5 seconds; if it's too short, it's easy to fail. From my experience, don't step on the brake pedal during the operation, as the system might misinterpret it as a start command. It's recommended to take a photo of the dashboard status before attempting, so you can show it to the mechanic if the reset isn't successful. Although it doesn't affect driving, having the reminder pop up every time you start the car is really annoying.

[MacChristopher]

The maintenance reminder reset for the Lynk & Co 03 involves five steps: After turning off the vehicle, hold down the TRIP button, turn the key to the power-on position, release the button when the icon flashes, immediately press the TRIP button again for 3 seconds, and start the engine to verify after the prompt disappears. Note: Do not operate while the steering wheel is turning, as the electric power steering may interfere with signal transmission. Models after the 2004 version use a new system; if the operation is ineffective, you may need to hold down the OK button simultaneously. When replacing the cabin air filter yourself, remember to record the date so you can determine if maintenance is truly needed when you see the reminder.

[StAlan]

There's a little trick to remove the wrench icon on the dashboard. My 03 is the 1.5T Jin Pro version. First, close all doors and roll up windows to avoid interference. Press the start button without stepping on the brake to enter power-on mode. Then long-press the TRIP button with your right hand for about 8 seconds - release immediately when the warning light goes off. Key point: This must be done after maintenance, otherwise the ECU will continue countdown. I once forgot to change oil before resetting and drove 8,000km before remembering maintenance. If unsuccessful, don't panic - holding the center console HOME button for 10 seconds forces a system reboot.

[StHope]

Let me demonstrate my operation process step by step: Turn the key to the LOCK position and wait for 30 seconds to ensure complete power-off of the vehicle. Then, firmly press the TRIP button on the steering wheel with your left thumb while turning the key to the ACC power-on position. Keep a close eye on the instrument cluster, and release the button when the maintenance light flashes for the third time, then immediately press and hold the button again until the light goes out. The entire process should not exceed 15 seconds, but pay attention to two key points: First, this must be done when the engine is cold. Second, press the button vertically on its side rather than the front face. For the mid-to-high trim models of the new 03 with digital instrument clusters, it's recommended to simultaneously reboot the central control screen to prevent data conflicts. This method is particularly effective for older 03 models, saving you 200 yuan in labor costs by avoiding a trip to the 4S shop.