How to choose between ID.4 X and ID.4 CROZZ?

What are the engine specifications for the 10th-generation Civic?

The 10th-generation Civic is equipped with two engines of different displacements. The 1.5T turbocharged engine model is L15B8, with a maximum horsepower of 177 HP, maximum power of 130 KW, maximum power speed of 6000 rpm, and maximum torque of 220 and 226 N.m. The 1.0T turbocharged engine model is P10A1, with a maximum horsepower of 125 HP, maximum power of 92 KW, maximum power speed of 5500 rpm, and maximum torque of 173 N.m. The engines used in the 10th-generation Civic adopt imported technology but are assembled and produced in China, hence they are classified as domestically produced engines. For daily maintenance of the 10th-generation Civic's engine, the following methods can be applied: Use lubricating oil of the appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional equipment of the intake and exhaust systems and usage conditions. For diesel engines, choose CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, its performance deteriorates, leading to various engine problems. To avoid malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through the filter element, it may rupture the filter element or open the safety valve, allowing oil to bypass through the relief valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Periodically use a radiator cleaner to flush the radiator. Removing rust and scale deposits not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.

20

1

Share

What brand of car is MG?

MG is the Morris Garages car brand. Originally a British automobile brand, the company was renowned for producing the famous MG series of convertible sports cars. In 1910, William Morris established Morris-Garage in Oxford, England, becoming the first car dealer in Oxford. In 1920, the first Morris car was manufactured in the town of Cowley, marking Morris-Garage's transition from car sales to car production. Here is some relevant information about MG cars: 1. Key Figures in Development: Three individuals played crucial roles in MG's nearly century-long history—William Morris, the father of the MG brand; Cecil Kimber, the founder of the MG brand; and John Thornley, who led the brand to its glorious expansion and established the world-renowned MG Car Club (MGCC), the largest single-brand car club globally. These three figures respectively infused the brand with vitality, shaped its soul, and guided its growth. 2. Development Direction: MG has proactively responded to new consumer demands by officially launching the MG-Live-APP. This app, independently developed by the MG brand, serves as an online interactive platform co-created by MG fans and car owners. Its main features include: MG new car test drives, online car viewing, customization and ordering, financial services, live interaction, after-sales service, smart car control systems, and a personalized peripheral store.

6

2

Share

When reversing, if the steering wheel is turned to the right, which direction do the rear wheels move?

When reversing, if the steering wheel is turned to the right, the rear wheels will move to the right. During reversing, it is essential to master the operation method of 'drive slowly, steer quickly.' Turning the steering wheel to the left will make the rear of the car turn left, while turning it to the right will make the rear turn right—the steering method is the same as when driving forward. Here are some precautions for reversing: Master the basic technique: Before reversing, observe the surroundings carefully and decide whether the rear of the car should move left or right. Additionally, determine how much to turn the steering wheel by finding reference points in the rearview mirror, and only proceed after careful consideration. When making corrections: If the rear of the car is leaning to one side, if the car body is leaning left, it must be moved right to straighten, so turn the steering wheel to the right, and vice versa. Only after the steering is corrected (adjusted) can turning the wheel to the other side change the direction of the rear. Before the steering is corrected, turning the wheel back can only reduce the degree of deviation of the rear.

4

0

Share

What Causes the Shock Absorber Spring to Make a Popping Sound When Turning?

Shock absorber springs making a popping sound when turning may be due to damage to the planar bearing inside the shock absorber spring or aging of the shock absorber top rubber. It is recommended to directly replace the shock absorber or the shock absorber top rubber. Generally, shock absorbers should be replaced every 4 years, and the shock absorber top rubber is best replaced every 80,000 kilometers. Specific explanations are as follows: Shock Absorber: Generally, shock absorbers should be replaced every 4 years. When replacing shock absorbers, they should be replaced in pairs; otherwise, it may lead to uneven balance of force distribution in the car, causing different forces on the shock absorbers and further shock absorber issues. Shock Absorber Top Rubber: The shock absorber top rubber is used to cushion the impact between the shock absorber spring and the car body. When driving on uneven roads, each top rubber bears more than a quarter of the car's weight impact. A silicone pad can be added to the shock absorber top cover, and adding silicone to the shock absorber is useful.

1

2

Share

What does it mean when the EPC light comes on in a Golf?

Golf EPC light coming on is mainly caused by a dirty throttle body. At this time, you only need to clean the throttle body and then rematch it to solve the problem. Definition of EPC in cars: EPC stands for Electronic Power Control, and this indicator light staying on represents a fault in the engine or electronic system. If the light stays on or flashes after ignition or during driving, it means the management system has detected a fault in the engine or electronic system. Please contact a service station immediately. Function of EPC in cars: It enables precise control of the throttle opening, improving fuel economy. The system responds quickly, providing satisfactory handling performance. It integrates idle control, cruise control, and vehicle stability control, simplifying the control system structure.

13

2

Share

What Causes Abnormal Noise in the Rear Wheels When Braking?

Abnormal noise in the rear wheels when braking may be caused by the following reasons: Break-in period for new cars: New cars or newly replaced brake pads have a break-in period, during which some abnormal noise may occur. Typically, the noise will disappear after the car has been driven for a few hundred kilometers. Normal ABS activation: The ABS system operates in a cycle of locking and releasing the brakes, keeping the vehicle in a state of near-lock rolling. When the ABS is activated by hard braking, it may produce a clicking sound, which is normal. In this case, simply press the brake pedal firmly to the floor. Severely worn brake pads: Worn-out brake pads can also cause abnormal braking noise. Most brake pads have wear indicators that will make a sharp noise when the pads are worn to their limit, signaling the need for immediate replacement to avoid accidents. Foreign objects between the brake discs: Small stones or a water film between the brake disc and pad can cause abnormal noise. This can often be resolved by pressing the brake pedal a few more times or removing the small stones.

10

0

Share

How to choose between ID.4 X and ID.4 CROZZ?

What are the engine specifications for the 10th-generation Civic?

What brand of car is MG?

When reversing, if the steering wheel is turned to the right, which direction do the rear wheels move?

What Causes the Shock Absorber Spring to Make a Popping Sound When Turning?

What does it mean when the EPC light comes on in a Golf?

What Causes Abnormal Noise in the Rear Wheels When Braking?

Does the Vezel have a manual transmission model?

What to Do If You Forget to Bring Your Driver's License During a Vehicle Inspection?

Can You Still Drive with Tire Pressure at 2.0?

What are the reasons for a refrigerated truck not cooling?