How to Check Fuel Consumption on Volkswagen Tayron?

1 Answers
MacFrank
07/30/25 9:52am
Tayron's fuel consumption can be viewed on the LCD instrument panel. With the central control screen turned on, press the CAR button on the lower left to display driving information (driving distance, average speed, driving time, average fuel consumption). Below are the specific details of Volkswagen Tayron: 1. TAYRON Tayron is a German premium midsize SUV from FAW-Volkswagen, offering four powertrain options: 280TSI, 330TSI, 380TSI, and both front-wheel drive and four-wheel drive. 2. Tayron has a length of 4595mm, width of 1860mm, height of 1660mm, and wheelbase of 2731mm. 3. Tayron is equipped with the EA888 2.0T turbocharged engine and features the DQ500 seven-speed wet dual-clutch transmission.
Was this review help?
9
4
Share
More Forum Discussions

What Causes Water Leakage Under the Car Chassis When Parking?

Possible causes of water leakage under the car chassis when parking include: 1. It's normal if you've just driven through wet roads; 2. It's also normal if you've been using the air conditioning while driving; 3. If neither situation applies, the leakage is abnormal, and you should visit a repair shop for inspection. The leaking fluid could be coolant or engine oil. Most car engines are water-cooled, relying on coolant circulation for heat dissipation. The coolant follows two circulation paths: major and minor cycles. During cold starts, the coolant undergoes minor circulation (bypassing the radiator) to help the engine warm up quickly. Once the engine reaches optimal temperature, major circulation activates to maintain normal operating temperature.
11
1
Share

How to solve the high water temperature issue of CFMOTO 650MT?

Installed radiator guard mesh, it is recommended to remove it, because the 650MT is a road-oriented ADV, the radiator is not so easily damaged, and the guard mesh may actually affect heat dissipation. You can try replacing it with a higher-grade coolant.
4
2
Share

What to Do When the Electric Bike Key Won't Turn?

Turn the handlebar to the left to find a certain angle, then try turning the key while adjusting the handlebar to make it turnable, or apply lubricating oil to the lock cylinder. Twist the key to rotate the handlebar several times to adjust its position. If the key is inserted but won't turn or is not flexible.
11
5
Share

How to Quickly Bleed Air from a Manual Grease Gun?

Unscrew the grease gun nozzle to separate it from the barrel. Lock the locking tab at the rear of the barrel and push the handle at the barrel end all the way in. Submerge the open end of the grease gun into the grease bucket to a depth of about 30 mm, then pull the handle at the barrel end to draw grease into the tube. Reattach the grease gun nozzle, hold the locking mechanism at the barrel end, and push the follower handle to begin bleeding air. Use your fingertip to control the air vent until grease emerges from the vent, indicating that the air has been fully bled.
1
5
Share

How long does it take to charge the battery by idling after jump-starting?

After jump-starting, it takes about 2 to 3 hours to charge the battery by idling. Idling can help charge the battery. The functions of the battery: 1. Power the engine starting system, ignition system, and supply electricity to the car; 2. Provide power to the car's electrical equipment when the engine is stopped or at low idle speed; 3. Participate in power supply when the electrical demand exceeds the generator's supply capacity; 4. Act as a voltage stabilizer for the entire vehicle's electrical system, mitigating impact voltage in the electrical system and protecting the car's electronic equipment. Methods to check if the battery has power: 1. Check the battery's charge indicator; 2. Measure the battery's static voltage; 3. Check the battery fault light; 4. Observe if the dashboard flickers or dims when starting the car; 5. Check if the battery shows signs of bulging, deformation, oxidation, or leakage.
1
1
Share

How to Install Anti-Collision Strips and Corner Guards?

For adhesive-type anti-collision strips, they are generally applied to the most vulnerable areas of car doors where impacts are likely to occur. The cross-section of strip-type protectors is U-shaped, with double-sided tape attached to the inner side of the U. During installation, the U-shaped groove should be fitted onto the edge of the car door.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.