How to adjust the seat height of Honda Civic?

1 Answers
DiAriana
07/29/25 4:11am
Method to adjust the seat height of Honda Civic: When adjusting the seat height, pull the lever on the inner side of the vehicle seat. Generally, the seat adjustment switch is located on the side of the seat. The seat adjustment switch can be either manual or automatic, with the same function and principle, only the control method differs. The length, width, and height of the Honda Civic are 4649mm, 1800mm, and 1416mm respectively, with a wheelbase of 2700mm. The new Civic basically follows the design of the overseas model, equipped with full LED headlights. The side design of the Civic is more bold than the front, with the gentle transition of the C-pillar resembling a Coupe model, featuring bracket-style LED taillights, and the light group presenting a dart shape.
Was this review help?
1
1
Share
More Forum Discussions

Is it normal for a car to overheat at high speeds but not at low speeds?

It is not normal for a car to overheat at high speeds but not at low speeds. Here are some relevant explanations about a car overheating at high speeds: 1. Causes: When the car is moving slowly, cooling relies on the wind generated by the cooling fan. If the fan speed slows down, it can cause the water temperature to rise when the car is moving slowly. It could also be due to excessive dust on the radiator fins, leading to poor heat dissipation. 2. Common faults: The engine cooling system may be low on antifreeze, possibly due to leaks in the engine, such as a water pump leak, damaged pipes, or a damaged radiator. Another issue could be a faulty thermostat in the engine cooling system, which prevents it from opening and obstructs the flow of coolant within the engine, causing the coolant temperature to rise excessively.
11
1
Share

How to Remove 502 Glue from Car Body?

Apply Huarun High-Efficiency Adhesive Remover to the area with glue. Below is relevant information about cleaning the car body: 1. Technique: Carefully check whether doors, windows, and other parts are tightly closed. It is essential to thoroughly inspect whether doors, windows, trunk lids, and other parts are tightly closed. Otherwise, high-pressure water jets during car washing may enter the cabin through unsealed gaps, potentially causing serious consequences. 2. Precautions: Pay attention to electrical safety and correctly use cleaning equipment and eco-friendly water-saving devices according to operational procedures. Use soft water for car washing and avoid hot water as much as possible. The coolant temperature should typically be between 30~40°C. Avoid using alkaline water and hard water with high mineral content. Washing the car body with hard water may leave marks or a film on the surface after drying.
17
3
Share

Does the old Bora have a USB interface?

The old Bora does not have a USB interface, but the new Bora has a USB interface. Here is some extended information: 1. Exterior Design: The new Bora adopts Volkswagen's family-style front face design, with distinct layers in the headlights and a wing-shaped design, giving it a strong three-dimensional feel. The rear design has changes in the outline and light clusters compared to the current model, and the body lines are also significantly different from the current Bora, becoming more streamlined. It also features a newly designed aluminum alloy wheel style. 2. Interior Changes: The new Bora uses the latest components in areas such as the steering wheel, instrument panel, and center console. Volkswagen's modular production method is indeed very successful, with multiple models using the same steering wheel, multimedia system, etc.
14
0
Share

What are the steps to replace the air conditioning filter in a Mercedes-Benz?

Mercedes-Benz air conditioning filter removal and replacement steps are as follows: 1. The air conditioning filter is installed at the rear of the glove compartment on the passenger side. To replace the filter, first open the glove compartment cover. 2. Locate the fixing buckle on the right side of the glove compartment and pull it outward with force. Remove the fixing buckle of the glove compartment cover to detach it. 3. Squeeze both sides of the glove compartment towards the center with both hands, then remove the glove compartment to reveal the air conditioning filter cover. Press the fixing buckles on both sides of the cover with force to remove it. 4. Pull the old air conditioning filter outward, install the new air conditioning filter, and restore it to its original position in the reverse order of disassembly.
12
3
Share

How to Clean the Throttle Body on a New Jetta?

Here are the detailed steps for cleaning: 1. First, start by removing the throttle body: Before removing the throttle body, always detach the air intake pipe first. 2. Loosen a total of 4 screws on the top and bottom of the throttle body, and use pliers to remove the two return hoses on the right side of the throttle body, as well as one pressure hose on the left side, totaling 3 hoses. Carefully unplug the throttle body connector. 3. First, remove the metal clips around the black plastic part. 4. After removal, gently open the back cover parallel to the throttle body by hand to prevent the gears from falling out. 5. Use original engine oil to lubricate the motor and gears. 6. Also lubricate the motor's rear post, then reinstall the motor, secure the gears, insert the gasket, close the cover, and hammer the metal clips back into place for fixation. 7. Finally, reinstall the throttle body.
17
2
Share

How to use the navigation in Mercedes-Benz C260L?

The navigation function in the COMAND system of the Mercedes-Benz C-Class can be used in the following ways: address input search, voice input, map point selection, and contacting customer service. The navigation function in the Mercedes-Benz C-Class is designed to be simple and practical, with functional settings similar to many mainstream map apps today. You can customize voice prompts, road conditions, and other information according to your needs, making it very convenient. Here are the specific details: 1. Address input search. First, select the city, then the district, and then the specific street. Since touchscreen operation is not available, and the touchpad operates almost the same way as the knob, selecting a location requires following the pinyin prompts shown in the image. Text input can also be done via the touchscreen here. 2. Voice input. Press the voice button on the steering wheel to start voice operation. 3. Map point selection. The map point selection in the operation interface is relatively easier. Simply access this function from the menu, and you can select points on the map, while the knob can easily adjust the map size for more convenient selection. 4. Contact customer service. By contacting customer service, the agent can directly send the destination to the vehicle.
3
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.