···
Log in / Register

How to adjust the clock on the Volkswagen Magotan?

5 Answers
Andrea
07/23/25 9:26pm

Method to adjust the clock on the Volkswagen Magotan: 1. Press the one-touch start button on the vehicle's center console to power on the instrument panel; 2. Press the SET button on the left side of the steering wheel; 3. Use the up and down option toggle buttons on the right side of the steering wheel to adjust the vehicle time; 4. Press the OK button on the steering wheel to confirm the changes; 5. Observe the instrument panel to ensure the time is displayed correctly. The Volkswagen Magotan is a mid-size car under FAW-Volkswagen, with dimensions of 4865mm in length, 1832mm in width, and 1471mm in height, and a wheelbase of 2871mm. In terms of suspension, the front suspension of the Magotan is a MacPherson strut independent suspension, and the rear suspension is a multi-link independent suspension.

Was this review help?
1
5
Share
Willa
08/10/25 5:09pm

I've been driving my Magotan for over two years and have adjusted the time several times. For most newer models, you can do it directly on the center console screen: first tap the 'Menu' button at the bottom of the screen, enter the 'Settings' option, and find 'Time and Date'. Once inside, you'll see the hour and minute display, and you can adjust them by sliding your finger. For older models, you'll need to use the steering wheel buttons: use the left directional button to switch to the dashboard menu, select 'Settings' - 'Time', and adjust using the volume knob. Note that you need to start the vehicle to perform these operations, and after adjusting, try turning off and restarting to see if the changes are saved. If you find the time keeps resetting to zero, it might be due to insufficient battery power or a system malfunction, in which case it's best to visit a 4S shop to check the onboard computer module. During long-distance road trips when encountering time zone changes, manually adjusting the time is more reliable than relying on automatic GPS synchronization.

Was this review help?
13
3
Share
Expand All
Sam
09/23/25 5:02am

As a seasoned driver who often helps friends with car issues, adjusting the clock in a Magotan is recommended to be handled by model. For models with a touchscreen, simply enter the vehicle settings menu and locate the clock icon to make adjustments. For models with physical buttons, press and hold the '0.0/set' button next to the instrument panel until the hour digits flash, then use the '+/-' buttons on the turn signal lever to adjust the time. After adjustment, briefly press 'set' to confirm. Three key reminders: first, perform the operation with the engine running to avoid power loss; second, check if the time on the instrument panel and the central control screen is synchronized after adjustment; third, if a clock symbol flashes on the instrument panel, it indicates that the car key signal needs to be rematched.

Was this review help?
14
1
Share
Expand All
RafaelLee
11/06/25 7:17am

Just helped my neighbor adjust his 2017 Magotan a couple of days ago. After starting the vehicle, hold the 'OK' button on the right side of the steering wheel for three seconds, then select the 'Settings' menu. Use the directional keys to find the 'clock' option and enter it. Use the left/right keys to switch between hours and minutes, and the up/down keys to adjust the values. The key operations need to be continuous; the menu will exit if no action is taken for more than five seconds. If you find the time is inaccurate, first check if any modifications to the central control screen have caused system conflicts. The original factory screen usually has a hidden reset pinhole in the lower right corner. Remember to calibrate the date at the same time, otherwise, navigation reminders may be incorrect.

Was this review help?
16
4
Share
Expand All
FelixLee
12/28/25 2:16am

The clock adjustment method for the Magotan varies depending on the trim level. For high-end trims, it's simplest: swipe to the far-right screen on the central display and tap the clock numbers to enter edit mode directly. For mid and low trims, simultaneously press the 'MENU' and 'DEF' buttons on the climate control panel for five seconds until a prompt tone sounds, then rotate the air volume knob to adjust hours. Press the 'AC' button to switch to minute adjustment. It's recommended to turn off the radio during operation to avoid signal interference. Special note: for models with mechanical ignition, keep the engine running. If the infotainment system has been modified, restoring factory settings usually resolves time reset issues.

Was this review help?
11
1
Share
Expand All
More Forum Discussions

How to adjust the time on the 8th generation Accord?

The method to adjust the time on the 8th generation Accord: Press and hold the SOUND button until you hear a beep, and the time on the LCD display will start flashing. Then, press the 4 button to adjust the hour, the 5 button to adjust the minutes, and the 6 button to set the minutes to 00. After adjusting to the correct time, press the SOUND button again, and the time will stop flashing, indicating that the time has been successfully set. The 8th generation Honda Accord is equipped with three engines: a 2.0L naturally aspirated engine, a 2.4L naturally aspirated engine, and a 3.5L naturally aspirated V6 engine. In terms of body dimensions, the 8th generation Accord measures 4945mm in length, 1845mm in width, 1480mm in height, and has a wheelbase of 2800mm.
1
1
Share

Where is the cigarette lighter fuse located in the Mazda6?

The cigarette lighter fuse in the Mazda6 is located inside the fuse box near the driver's left foot. Here is some information about the cigarette lighter: 1. The cigarette lighter is a component found in all cars, designed to provide a flame source for smokers. 2. Some cigarette lighter sockets remain powered even after the car is turned off, so it's better to plug and unplug devices as needed. When plugging or unplugging devices, avoid shaking them too forcefully, as this can lead to poor contact during subsequent use. In more severe cases, it may cause a short circuit, resulting in the fuse and external device burning out. Therefore, always remove devices vertically. 3. Remember to regularly clean the cigarette lighter socket to remove any foreign objects. Never allow conductive materials such as metal objects or liquids to enter, as this can cause short circuits and fuse blowouts.
3
5
Share

What Causes Abnormal Noise and Failure to Start When Igniting the Car?

The reasons for abnormal noise and failure to start when igniting the car are: insufficient battery power or low voltage. 1. Before turning off the car, forgetting to turn off the headlights or some electrical equipment may cause the battery to drain, resulting in insufficient power. 2. If the battery has been used for too long and is severely aged, the voltage may be insufficient, requiring replacement. Additional information: The method to determine whether the battery has sufficient power is: Turn the ignition key to the ON position (for push-button start models, press the start button twice without stepping on the brake), turn on the headlights, and observe if the light dims significantly or does not light up at all. You can also press the horn; if the sound is noticeably weaker than usual or does not sound at all, it can be concluded that the battery power is insufficient.
12
1
Share

What does AUTO-H mean on a BMW car?

The AUTO-H button indicator in the car refers to the automatic parking function equipped on BMW vehicles. When waiting at a traffic light, after stepping on the brake to stop the vehicle, this function will automatically engage the parking state, eliminating the need for the driver to keep pressing the brake pedal for a long time. To move again, simply press the accelerator pedal. Here is a brief introduction about AUTO-H: 1. The AUTO-HOLD system in cars is also known as the automatic parking assistance system. Its main function is to automatically determine the vehicle's specific state, pre-tension the electronic parking brake, and thus serve the purpose of parking. 2. This function has an independent button for activation and deactivation on vehicles equipped with an electronic parking brake. The AUTO-HOLD button is located behind the electronic parking brake. To use it, first press this button until the indicator light comes on, and the system will officially enter standby mode.
20
2
Share

Does the Cavalier have tire pressure monitoring?

The Cavalier's Xinyue and Xinshang trims come equipped with a tire pressure monitoring system. The tire pressure monitoring system functions by automatically monitoring the tire pressure in real-time while driving and alerts the driver in case of tire leaks or low pressure to ensure driving safety. Here is more information about the tire pressure monitoring system: 1. There are two main types of tire pressure monitoring systems: one is the indirect type (Wheel-Speed-Based TPMS, WSB), which uses the wheel speed sensors of the car's ABS system to compare the rotational speed differences between tires. The other is the direct type (Pressure-Sensor-Based TPMS, PSB). 2. This system uses pressure sensors installed in each tire to directly measure the tire pressure and transmits the pressure information from inside the tire to a central receiver module via wireless transmitters, then displays the tire pressure data for each tire. The system will automatically alert the driver when the tire pressure is too low or there is a leak.
15
3
Share

Does the Sylphy have ISOFIX interfaces?

The Sylphy is equipped with ISOFIX interfaces. They are located in the crevice between the backrest and the seat cushion of the rear seats, as well as at the upper rear part of the seats. The installation method for the ISOFIX fixation is as follows: 1. Simply align the ISOFIX interface of the child safety seat with the reserved slot on the seat, insert it, and then raise the support rod to complete the installation. 2. If the car does not have ISOFIX interfaces, you can use the LATCH interface for fixation or install ISOFIX interfaces yourself on the rear seats of the car. 3. Compared to the simple ISOFIX interface, LATCH solves the problem of no top fixation and, due to its non-rigid connection, has more lenient requirements for the anchor point positions of the car seats. 4. Locate the LATCH interface position and secure the hook strap to the car's LATCH interface.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.