How to activate automatic window closing when locking the car for Tiguan L?

How often should a private car generally have its refrigerant recharged?

For average-performance cars, the refrigerant recharge cycle is shorter, typically requiring a recharge within two years. High-performance vehicles have a longer recharge cycle, often needing a recharge only after eight years. Below are some precautions for car refrigerant recharge: Before recharging: It is necessary to use a pressure vacuum machine to pressurize and check for leaks. If any leaks are found, components of the air conditioning system such as the air conditioning pipe joints, condenser, evaporator, compressor, etc., should be inspected by spraying foam water. Any detected leaks should be repaired or replaced. Vacuuming: It is essential to vacuum for at least half an hour to prevent water vapor from remaining in the pipes. Connect the refrigerant gauge to the air conditioning system and vacuum, focusing on the low-pressure side. Generally, there's no need to monitor the negative pressure value during vacuuming; three minutes is sufficient. After this, tighten the switch on the low-pressure gauge and connect the refrigerant tank for filling.

20

5

Share

How to Solve the Ticking Noise in the 2013 Sonata 8 Engine?

To address the ticking noise in the 2013 Sonata 8 engine, the following aspects need to be checked: 1. When the car is idling, if the sound heard inside the car is not too loud, it may be coming from the valve or fuel injector: slightly press the accelerator while the car is idling to see if the frequency changes. If the frequency changes, it indicates noise from the valve; the sound from the fuel injector is generated at the valve area. 2. During cold starts, the engine may produce noise: when the engine is cold, the gap between the cylinder wall and piston is not at its optimal size, and the lubrication from the oil is not sufficient. Typically, when the engine block temperature reaches around 95 degrees, the sound will return to normal. 3. Poor-quality oil or not changing the oil for an extended period: this can increase friction between the valve and guide, as well as in the hydraulic lifters, making various noises in the engine louder.

11

5

Share

Can You Shift Directly from Fourth Gear to First Gear?

Shifting directly from fourth gear to first gear is not recommended, as it can easily lead to engine stalling, jerking, and damage to the transmission's mechanical structure. Gear shifting, short for "gear lever operation method," refers to the process of continuously changing the position of the gear lever based on road conditions and vehicle speed. Below is additional information: Oil Leakage: If oil is seeping from the transmission housing or oil pan, one possible cause is aging seals leading to poor sealing; another reason could be manufacturing defects causing pinholes in the housing. Engine Stalling When Engaging Gear: If the engine stalls when shifting into D or R, the issue might be due to a faulty lock-up solenoid valve or a stuck lock-up control valve. Locking: Incorrect input or output signals from the transmission, or issues with components or wiring, can cause this. Sometimes, communication problems between the transmission computer and other system computers may also be responsible. No Response When Engaging Gear: After shifting into D or R and releasing the brake, the vehicle does not move. This is often caused by damage to the input shaft or reverse clutch, or a faulty D/R brake.

19

0

Share

Can You Shift Directly from Fourth Gear to Second Gear?

You can shift directly from fourth gear to second gear. However, skipping gears for deceleration causes significantly more wear and tear on the internal components of the car compared to sequential downshifting. Precautions for Gear Shifting: When downshifting, the double-clutching method with a throttle blip should be used. The principle of throttle blipping during downshifting is: the faster the speed, the larger the "throttle blip"; the slower the speed, the smaller the "throttle blip". At low engine speeds, the "throttle blip" should be larger; at high engine speeds, it should be smaller. On flat roads, the "throttle blip" should be larger; when going uphill, it should be smaller. Gear Shifting Techniques: Shifting should be timely, accurate, smooth, and quick. When starting the car, generally use the low gear (first gear). Once moving, shift up through the gears promptly as road conditions permit.

16

5

Share

What is the material of clutch friction plates?

Clutch friction plates are made of powder metallurgy materials, asbestos-based materials, and paper-based materials. The main requirements for friction plate materials are: 1. Large and stable friction coefficient, with the dynamic friction coefficient as close as possible to the static friction coefficient; 2. High strength, capable of withstanding impact, and not prone to cracking or peeling at high speeds; 3. Wear-resistant, heat-resistant, corrosion-resistant, with good thermal conductivity and small thermal deformation; 4. Should not adhere when left stationary for long periods; 5. Long service life and easy to process. Friction plates are the main components of friction clutches, and the physical properties and mechanical performance of their working surface materials directly affect the clutch's performance.

18

4

Share

How many points will be deducted for overloading a private car by one person?

Overloading a private car by one person will result in a deduction of 2 points. Below are the relevant provisions of the "Road Traffic Safety Law of the People's Republic of China": Article 49: Motor vehicles shall not carry more passengers than the approved number, and passenger vehicles shall not carry goods in violation of regulations. Article 92: If a highway passenger vehicle carries more passengers than the approved number, a fine shall be imposed. If the number of passengers exceeds 20% of the approved capacity or goods are carried in violation of regulations, a fine shall be imposed. If a freight vehicle exceeds the approved load capacity, a fine shall be imposed; if the load exceeds 30% of the approved capacity or passengers are carried in violation of regulations, a fine shall be imposed. Notes: Overloading a vehicle will reduce its braking, steering, and other performance. Excessive load mass will increase the vehicle's inertia, lengthen the braking distance, and increase the risk. Due to the exponential increase in total load mass, the braking effect on slopes is weakened, turning sensitivity is reduced, and the risk of accidents such as failed braking, rolling back, and tire blowouts is heightened.

6

3

Share

How to activate automatic window closing when locking the car for Tiguan L?

How often should a private car generally have its refrigerant recharged?

How to Solve the Ticking Noise in the 2013 Sonata 8 Engine?

Can You Shift Directly from Fourth Gear to First Gear?

Can You Shift Directly from Fourth Gear to Second Gear?

What is the material of clutch friction plates?

How many points will be deducted for overloading a private car by one person?

How much engine oil should be added to a Volvo XC60?

Why Shouldn't You Restart the Engine After Stalling in Water?

What are the reasons for the engine warning light in Mercedes-Benz W221?

How often should a private car be inspected after six years?