How often should the spark plugs of Volkswagen Tiguan be replaced?

1 Answers
RonanLynn
07/29/25 10:06pm
Volkswagen Tiguan spark plugs should be replaced approximately every 70,000 kilometers. If the spark plugs are not replaced for a long time, it may cause various issues such as leakage in the vehicle's ignition system, increased fuel consumption, reduced power, and most importantly, difficulty in ignition, affecting the normal use of the vehicle. Spark plug replacement cycle: Under normal maintenance conditions, spark plugs should be replaced after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine, so it is recommended to follow the user manual. The following standards can be used as a reference for maintenance and replacement: platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. Steps for replacing spark plugs: Open the hood, lift the engine's plastic cover, and remove the high-voltage distributor wires. Mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for any external debris such as leaves or dust and ensure they are cleaned thoroughly. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the removed high-voltage distributor wires in the order of the ignition sequence and secure the cover.
Was this review help?
4
1
Share
More Forum Discussions

What kind of engine oil is suitable for the Fit?

It is recommended to use the original Guangzhou Honda engine oil for the Fit. The original engine oil is formulated according to the vehicle's performance requirements, and regular replacement as per the manufacturer's maintenance manual is sufficient. Below is relevant information about engine oil: 1. Engine oil serves to lubricate and reduce friction in the engine, assist in cooling, seal against leaks, prevent rust and corrosion, and provide shock absorption. It is often referred to as the 'blood' of a car. 2. Engine oil consists of two parts: base oil and additives. The base oil is the main component of the lubricant, determining its basic properties, while additives compensate for and improve the deficiencies of the base oil, providing certain new characteristics, making them an essential part of the lubricant. 3. High-quality engine oil, especially fully synthetic oil, not only protects the engine and reduces the frequency of oil changes but also helps save on gasoline expenses.
6
2
Share

How to Check Tire Pressure in the Mazda 3 Axela?

The method to check tire pressure in the Mazda 3 Axela is as follows: When the system detects that one or more tires have low pressure, the low tire pressure warning light on the instrument cluster will illuminate. In vehicles equipped with a Driver Information Center (DIC), a "CHECK TIRE PRESSURE" message will also appear. If this message appears, you should immediately stop and check all tires for damage. After repairs, the Tire Pressure Monitoring System (TPMS) must be reset. The reset procedure is as follows: 1. For vehicles equipped with a Driver Information Center (DIC): a. Turn the ignition to the ON position. b. Press and hold the Gage button on the far right of the DIC until the instrument cluster screen displays "TIRE MONITOR SYSTEM." c. Press the SET/RESET button with the arrow until the message "TIRE MONITOR SYSTEM HAS BEEN RESET" appears. d. The reset is now complete. 2. For vehicles without a Driver Information Center (DIC): a. Turn the ignition to the ON position. b. Press and hold the Odo/Trip button to cycle through the odometer displays until only the total mileage is shown. c. Press and hold the Odo/Trip button again. After a few seconds, the low tire pressure warning light will flash. When you hear two beeps, the reset is complete.
13
4
Share

How to Turn Off the Start-Stop Function on a 2019 Sagitar?

The start-stop switch for the 2019 Sagitar is located in front of the gear lever, featuring a button with a capital 'A' inside a circle and 'OFF' below it. The start-stop system is automatically enabled when the ignition is turned on, and pressing the button once will deactivate it. Here is more information about the start-stop system: 1. Disadvantages: While the start-stop system saves fuel, it reduces comfort. The vehicle's acceleration is slightly slower than normal, and there is a slight vibration at the moment of starting. 2. Working Principle: When the vehicle stops due to traffic congestion or at an intersection, the driver presses the brake pedal and shifts to neutral. The start-stop system automatically detects that the engine is idling and in neutral, the wheel speed sensors of the anti-lock system show zero, and the electronic battery sensor indicates sufficient energy for a restart. The engine then automatically stops.
14
3
Share

What are the differences between the 2019 Golf and the 2018 model?

Here are the differences between the 2019 Golf and the 2018 model: 1. Exterior: The 2019 model features an additional shark fin antenna compared to the 2018 model. 2. The 2018 model has a 6.5-inch central control screen, while the 2019 model upgrades to an 8-inch screen. 3. The 230TSI version of the 2018 model, which was the low-power 1.4T variant, was discontinued and replaced entirely by the 280TSI high-power 1.4T version in the 2019 model. 4. The 2019 model adds two USB charging ports in the rear compared to the 2018 model. 5. The 2018 model lacked GPS navigation across all trims, while the 2019 model includes GPS navigation as standard, except for the base and low-end versions.
8
5
Share

What are the engine displacements of the Pajero?

The engine displacements of the Pajero are 3.0 liters and 3.8 liters. Below is an introduction to the 3.0-liter displacement: Naturally aspirated six-cylinder engine with a maximum horsepower of 174 hp, maximum power of 128 kW, and maximum torque of 255 N·m. Here are the advantages of the Pajero: 1. Youthful and sleek exterior design with an upgraded image, well-designed and functional cabin interior, easily adjustable driving position, spacious and comfortable seats, 3.8-liter V6 engine with ample power and quiet operation, and a well-matched 5-speed automatic transmission; 2. Independent suspension + body-on-frame construction, superior road performance compared to competitors, Mitsubishi's signature SS4 Super Select 4WD system, easy to use and reliable, equipped with a central differential lock and rear differential lock, strong off-road capability; 3. All three rows of seats feature independent air vents, thoughtful and practical, and the redesigned rear end improves rear visibility.
12
5
Share

What is the engine brand of the Bestune T77?

The engine of the Bestune T77 is independently developed by Bestune in China, making it a domestically produced engine. The engine model of the Bestune T77 is CA4GA12TD, with a maximum power output of 124 kW, a maximum torque of 258 Nm, and a maximum horsepower of 169. For daily maintenance of the Bestune T77 engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional equipment of the intake and exhaust systems and usage conditions; for diesel engines, choose CB--CD grade diesel engine oil according to the mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will deteriorate during use. After a certain mileage, the performance will degrade, leading to various engine issues. To avoid malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through, it may rupture the filter or open the safety valve, allowing oil to bypass the filter and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale deposits not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
6
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.