How many liters is a full tank for a 125cc scooter?

What are the methods to avoid crossing the line when turning in an S-curve during Subject 2?

Here are the methods to avoid crossing the line when turning in an S-curve during Subject 2: 1. When entering the curve, position the front of the car in the middle. When the left corner of the car touches the right line, turn the steering wheel left by one and a half turns (45 degrees) and maintain the course. When the left corner of the car touches the left line of the second curve, straighten the steering wheel. When the right corner of the car touches the left line of the second curve, turn the steering wheel right by one and a half turns (45 degrees). Once the car is straight, straighten the steering wheel and slowly exit the S-curve. 2. When navigating the S-curve, it is crucial to control the speed properly. Press the clutch gently to slow down, which increases reaction time. Even if the direction is slightly off, it can be adjusted in time to avoid crossing the line. 3. There are two entry directions: left entry and right entry. For a left entry, keep the vehicle as close to the right line as possible before turning the steering wheel left. For a right entry, do the opposite—keep the vehicle as close to the left line as possible before turning the steering wheel right. This accounts for the inner wheel difference, preventing the rear wheels from crossing the line during the turn.

19

2

Share

How to Replace Transmission Oil with a Flushing Machine?

There are currently two common methods for replacing transmission oil with a flushing machine: gravity oil change and flushing machine oil change. A flushing machine is a device that utilizes pressure to dynamically replace automatic transmission fluid. The principle involves simultaneously extracting the old oil and injecting new oil, using pressure to push out the old oil with the new oil. The advantages of using a flushing machine for oil change are as follows: 1. The oil change is more thorough, with an oil change rate of over 95%. 2. It is simple and labor-saving. 3. It can clean the internal sludge and metal debris of the automatic transmission, thereby appropriately extending the maintenance cycle of the transmission oil.

8

3

Share

Can Four-Wheel Drive Vehicles Not Be Towed?

Yes, but it depends on the situation. Among the three towing methods—tow rope towing, lift towing, and flatbed towing—only flatbed towing is suitable. Tow Rope Towing: Tow rope towing refers to providing power to the towed vehicle through a tow rope. It is not recommended to tow a four-wheel drive vehicle this way because if the vehicle is not started, the steering wheel cannot be turned, and the brake booster does not work. Forcibly towing may cause the anti-theft module and transmission to lock up, damaging the car. Lift Towing: This involves using a tow truck to lift the two front wheels of the towed vehicle off the ground, relying on the rear wheels to roll for towing. In a four-wheel drive vehicle, all four wheels rotate together, coordinated by the transmission, central differential, and drive shaft. If only the rear two wheels rotate, these three major components fail to coordinate, potentially causing damage to the drivetrain, central differential, and other parts, with significant harm to full-time four-wheel drive vehicles. Flatbed Towing: This method involves lifting the vehicle or using other means to place it on a flatbed truck. In this case, the vehicle is essentially parked on the truck, with neither the front nor rear wheels rotating. As long as it is properly secured, there is minimal risk of damage to the vehicle.

7

1

Share

Can the Key Be Pulled Out Without Engaging the P Gear?

No, the key cannot be pulled out without engaging the P gear. The P gear is a special neutral position that mechanically locks the transmission output shaft to secure the vehicle, functioning as a parking brake to prevent the vehicle from moving. Any gear operation related to the P gear requires the simultaneous use of the brake pedal and the button on the gear lever or pressing down the shift handle. Engaging the P gear: Press the brake pedal, then hold the safety button on the gear lever or press down the shift lever to move to any other gear position, ideally completing the action in one motion. Disengaging the P gear: Press the brake pedal, then hold the safety button on the gear lever or press down the shift lever to return any other gear position to the P gear.

6

3

Share

What are the length and width of the Audi A6?

Audi A6 has a length of 5.012 meters, a width of 1.855 meters, and a height of 1.485 meters. The following is an introduction about the Audi A6: 1. Audi A6 (Audi A6) is a luxury car produced by Audi, available in both sedan and station wagon models. The Audi A6 incorporates Audi's high-tech proprietary technologies, further enriches luxurious configurations, and is endowed with strong sporty characteristics. Its features include luxury, dynamism, and sophistication. 2. The Audi A6's multitronic continuously variable/manual transmission is the first in the history of luxury cars to achieve true continuously variable transmission. It uses a metal chain drive system, completely replacing the traditional gear set transmission method, resulting in completely smooth power output, smoother than conventional automatic transmissions, with the quick responsiveness of manual transmissions, while also being more fuel-efficient and providing more comfortable handling. The newly added S mode enhances acceleration capability and increases driving pleasure.

5

1

Share

Can the car be locked without shifting to P gear?

It is possible to lock the car without shifting to P gear. The P gear is a special neutral position that mechanically locks the transmission output shaft to secure the vehicle, functioning as a parking brake to prevent the vehicle from moving. Gear operations related to P gear require the simultaneous use of the brake pedal and the safety button on the gear lever or pressing down the gear shift handle. To engage P gear: Press the brake pedal, then hold the safety button on the gear lever or press down the gear shift handle to move to any other gear position, ideally completing the action in one motion. To disengage P gear: Press the brake pedal, then hold the safety button on the gear lever or press down the gear shift handle to shift back to P gear from any other gear position.

9

5

Share

How many liters is a full tank for a 125cc scooter?

What are the methods to avoid crossing the line when turning in an S-curve during Subject 2?

How to Replace Transmission Oil with a Flushing Machine?

Can Four-Wheel Drive Vehicles Not Be Towed?

Can the Key Be Pulled Out Without Engaging the P Gear?

What are the length and width of the Audi A6?

Can the car be locked without shifting to P gear?

Subject 5 Exam Content and Passing Standards?

How long does it take to get the result of Subject 4 application?

What brand of tires does the Trumpchi GA6 use?

What are the effects of parking on uneven roads for a long time?