How many kilometers can an Elysian run on a full tank of gas?

2 Answers
DelAnthony
07/24/25 5:16am
An Elysian can run about 500 kilometers on a full tank of gas. Here are some specific methods to reduce vehicle fuel consumption: 1. Minimize vehicle weight: Keep the interior simple and avoid carrying unnecessary items. For every additional kilogram of load, the car's fuel consumption increases by 1%. 2. Avoid excessive vehicle modifications: Adding spoilers, protective covers, or wings can disrupt the original aerodynamic design of the car, increasing wind resistance and consuming extra fuel. Modifying lights to increase electrical usage can also lead to unnecessary fuel consumption. 3. Develop good driving habits: Avoid sudden acceleration, driving at high speeds in low gears, prolonged idling, frequent lane changes, or braking. Aim for smooth starts, steady-speed driving, and reduced braking.
Was this review help?
18
5
Share
MacAngelina
08/11/25 12:55am
I usually drive an Elysian for my daily commute in congested urban areas. A full tank of 55 liters only gets me around 450 kilometers due to stop-and-go traffic, with fuel consumption reaching 12L/100km. On weekends, when I take the highway to the suburbs using cruise control, the fuel consumption drops to 8L/100km, allowing a full tank to last nearly 700 kilometers. On average, the driving distance on a full tank is around 550 kilometers. I recommend developing the habit of anticipating road conditions in advance, such as avoiding sudden braking and gently accelerating, which can add dozens of kilometers to your range. Maintaining proper tire pressure is also crucial, as low pressure increases fuel consumption and reduces range.
Was this review help?
3
4
Share
Expand All
More Forum Discussions

Is the Audi A4 front-wheel drive or rear-wheel drive?

Audi A4 low-end models are front-wheel drive, while high-end models feature Quattro all-wheel drive. Advantages of front-wheel drive: Adaptability: Audi front-wheel drive models are better suited for aggressive driving styles. Transmission efficiency: Front-wheel drive vehicles have higher transmission efficiency than rear-wheel drive vehicles. The engine and drive wheels are positioned close together, resulting in a short transmission distance without any conversion, maximizing engine efficiency. Fuel consumption: The structure of rear-wheel drive vehicles leads to increased power loss and higher fuel consumption. Interior space: Rear-wheel drive also affects interior space. Steering angle: Rear-wheel drive vehicles are driven by the two rear wheels, with the front wheels only responsible for steering and not driving. Therefore, rear-wheel drive vehicles have a much larger steering angle than front-wheel drive vehicles. Advantages of Quattro all-wheel drive: Quattro refers to Audi's all-wheel drive technology, which is a permanent four-wheel drive mode that maintains four-wheel drive under all conditions. Its core technology is the Torsen central differential, which features a worm gear planetary gear structure and operates purely mechanically without electronic system intervention. The working principle of Quattro is: When speed differences between the front and rear axles occur due to external conditions, the Torsen differential automatically transfers most of the power to the drive axle capable of handling the load, optimizing and distributing power to all four wheels. Due to the balanced distribution of axle load, drivers can better control steering precision and flexibility without the need for torque steering assistance.
20
2
Share

How to Lift the Wiper Blades on the Tiguan?

Park the Tiguan, remove the key, and push the wiper control lever downward to enter the maintenance mode, allowing you to lift the wiper blades. Here is additional information about the Tiguan: 1. The Tiguan is a compact SUV under Volkswagen, which has gained popularity among consumers since its launch. 2. The Tiguan is equipped with two engines: a 1.4-liter turbocharged engine and a 1.8-liter turbocharged engine. 3. The 1.4-liter turbocharged engine delivers 150 horsepower and a maximum torque of 250 Nm, with a maximum power at 5000 rpm and a maximum torque range from 1750 to 3000 rpm. This engine features direct fuel injection and uses an aluminum alloy cylinder head and block.
20
0
Share

What is the standard tire pressure for Honda Fit?

The tire pressure value for Honda Fit is generally between 2.4-2.5bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2bar in winter and decreased by 0.1bar in summer. This data is based on the international GBT2978-2008 standard. The Honda Fit has an automatic monitoring function, which does not require manual activation. When there is an abnormality in the tire, the dashboard will automatically display a message. The display does not show specific values but indicates which tire has a problem. The tire pressure needs to be restored to normal levels before the tire pressure data can be reset. Press and hold the tire pressure SET button on the center console until the tire pressure data refreshes, and the tire pressure warning light will disappear. Generally, a tire pressure exceeding 2.8bar is considered too high, while a tire pressure below 2.0bar is considered too low. Hazards of excessive tire pressure: Reduced tire friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates wear on the central tread of the tire, shortening its lifespan; increases body vibration, indirectly affecting the lifespan of other components; causes excessive stretching of tire cords, reducing tire elasticity and increasing the load on the car during driving. Hazards of insufficient tire pressure: Increased friction coefficient with the road surface, leading to higher fuel consumption; causes heavy steering and deviation, posing safety risks; increases movement in various parts of the tire, leading to abnormal heating due to excessive rolling; reduces the functionality of cords and rubber, causing delamination or cord breakage and excessive friction with the rim, damaging the tire bead area and causing abnormal wear; multiplies friction between the tire and the ground, sharply raising tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may lead to tire blowouts. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no stamp on top, four small spikes below, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure: Usually, an alarm is triggered when the pressure is below 1.8bar or above 3.0bar. In this case, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset: After inflating the tire, the tire pressure was not reset in time, causing the tire pressure monitoring system to still record the previous data, which triggers the tire pressure monitoring indicator light. Simply reset the tire pressure to resolve this issue. Damaged tire pressure sensor: The tire pressure sensor, which monitors tire pressure, is directly installed inside the tire and connected to the tire inflation port. If the sensor is damaged due to impact while driving, it can also cause the tire pressure warning light to come on. For sensor damage issues, only a complete replacement of the component is possible.
1
4
Share

How to Remove the Battery from a Magotan Remote Key?

Opening the Magotan's remote key is generally for battery replacement. The disassembly steps are divided into the following 6 steps: 1. Prepare a flat-head screwdriver about 3mm wide and a battery (CR2032). 2. Push the locking mechanism of the emergency key to remove the mechanical key. 3. Insert the flat-head screwdriver along the mechanical keyhole, gently turn it clockwise until the key cover pops out. 4. Remove the old battery, noting the positive and negative poles. 5. Insert the new battery, ensuring to use a new battery with the same voltage, structure size, and specifications, paying attention to the positive and negative poles. 6. Close the key cover and insert the mechanical key.
15
0
Share

What tires does the Roewe 360 use?

Roewe 360 uses MAXXIS tires with a tire specification of 205/55R16. MAXXIS tires focus on durability, wet road performance, and low noise. The tires on the Roewe 360 are circular elastic rubber products assembled on various vehicles or machinery to roll on the ground. They are usually mounted on metal rims, supporting the vehicle body, cushioning external impacts, ensuring contact with the road surface, and maintaining the vehicle's driving performance. The most important parameter of a car's tires is the tire pressure value. The car's tire pressure monitoring system provides safe and effective protection for driving. Tire pressure may rise or fall depending on temperature and region, so it's necessary to determine whether the car's tire pressure is within the normal range based on current conditions. The tire pressure range varies depending on the tire model and size, so it should be decided based on actual conditions. Generally, a tire pressure above 2.8 bar is considered too high, while a tire pressure below 2.0 bar is too low. Hazards of excessive tire pressure: Reduced tire friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates wear on the central tread pattern, shortening tire lifespan; increases vehicle vibration, indirectly affecting the lifespan of other components; overextends the tire cords, reducing elasticity and increasing the load on the vehicle during driving. Hazards of insufficient tire pressure: Increases friction coefficient with the road surface, raising fuel consumption; makes the steering wheel heavy and prone to deviation, compromising driving safety; increases movement in various parts of the tire, causing abnormal heat due to excessive rolling; reduces the functionality of cords and rubber, leading to delamination or cord breakage and excessive friction with the rim, damaging the bead area and causing abnormal wear; multiplies friction with the ground, sharply raising tire temperature, softening the tire, and drastically reducing strength. High-speed driving may lead to tire blowouts.
10
3
Share

How to Reset the Maintenance Light on a Jetta?

When the maintenance light on a Jetta comes on, it should be reset through three steps. Here are the detailed instructions: 1. Turn off the car and lock the steering wheel. 2. Press and hold the button on the right side of the dashboard (0.0/SET) with your left hand. Without releasing it, turn the key with your right hand to illuminate the dashboard without starting the engine. At this point, a small wrench-like indicator light will appear on the dashboard and remain steady. 3. Release the left hand and press the button on the left side of the dashboard. The wrench symbol will disappear, indicating the maintenance light has been successfully reset. The maintenance interval for a Jetta is 10,000 kilometers. Routine maintenance includes changing the engine oil and oil filter, replacing the three filters (air, cabin, and fuel filters), and checking and topping up the brake fluid, coolant, and power steering fluid (replace if necessary).
4
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.