How long does it take for a car to fill with water when submerged?

What is the issue with the Haval H6 air conditioning turning on automatically?

The air conditioning was not turned off before parking the car; the air conditioning is set to automatic start mode; the air conditioning control switch, control computer, and its control circuit are abnormal. How car air conditioning works: When heating, the car air conditioning utilizes the residual heat of the coolant, and when cooling, it uses the phase change of the refrigerant. When the heating function of the car air conditioning is activated, the high-temperature coolant from the engine flows through the heater core, behind which there is a blower, allowing warm air to blow out from the air vents. Cooling is more complex: after pressing the AC button, the compressor clutch engages, the engine starts to drive the compressor, which continuously compresses the refrigerant. How to turn on the heating in car air conditioning: First, start the car. After the engine runs for a while and the coolant reaches normal temperature, you can turn on the car's heating. Rotate the temperature control knob to the red zone and adjust the fan speed switch.

1

0

Share

Where to Place the Jack for a Corolla?

If changing a spare tire, the jack should be placed under the raised position on the side of the chassis near the door sill. Ensure the jack is positioned straight to prevent tilting or slipping, then you can proceed to change the tire. Precautions for using a car jack: Do not place the jack under the bumper position, as this can easily cause damage to the car's bumper. When using the car jack, ensure there are no passengers remaining in the car to avoid the risk of the jack slipping during use, which poses significant safety hazards. Precautions for changing a car tire: Use the jack to slightly lift the car, then use a tire wrench to loosen the tire nuts. Do not remove them completely; wait until the tire is lifted off the ground before fully removing them. The direction to loosen the screws is towards the rear of the car. When supporting the chassis with the jack, there are usually position indicators for the support points. Make sure the support point is perpendicular to the ground surface to avoid instability and tipping. After removing the old tire and installing the new one, tighten the nuts in a diagonal sequence.

8

5

Share

What is the Regal in the United States?

The Regal is an authentic American car, with its American prototype being the Buick LaCrosse by General Motors. Regal Powertrain: The Regal comes in three models: the 2.4L Luxury, 2.4L Elite, and 3.0L Flagship. The 2.4L version is equipped with a 2.4L all-aluminum four-cylinder engine, delivering a maximum power of 186 horsepower at 6400 rpm and a peak torque of 225 Nm at 4800 rpm. The 3.0L version features a V6 engine with a maximum power of 190 kW and a peak torque of 244 Nm at 4400 rpm. All models are front-wheel drive and come with a 4-speed automatic transmission with manual shift mode. Regal Features: The Regal comes standard with front dual airbags, four-wheel disc brakes, ABS, EBD, traction control system, aluminum alloy wheels, parking sensors, etc. It can be said that in terms of features, the Regal is much more advanced than the LaCrosse.

6

4

Share

Why did the Audi A3 suddenly go silent?

The reasons why the Audi A3 suddenly goes silent include: the car's engine stalling, the CD player being empty, or it may be caused by wiring issues leading to abnormal sounds. The entertainment system muting is a common issue with this model. If the restoration method cannot resolve it by pressing once, then you can only go to the 4S store for inspection. Below are the relevant introductions: 1. How to restore the Audi A3 from mute: You need to find the MENU button, the button in the upper right corner of the diagram, and the circular operation button at the central armrest position. After finding them, press all three buttons simultaneously, hold for about 3 to 5 seconds, then release to restart the MMI. 2. Methods to prevent the Audi A3 from going silent: After starting the car's engine, connect your phone to the car's system. You can use a data cable, USB, Bluetooth, hotspot, etc., to connect, which can avoid the vehicle going silent. Because when connected, the device is in use, and the car's system will not stall, causing the audio to go silent.

13

5

Share

How to Solve the Random Jumping Issue of the Excelle's Central Locking System?

If the central locking system of the Excelle exhibits random jumping behavior, it is necessary to visit a 4S shop to replace the door lock control assembly and the central control module. Below is relevant information: 1. Definition of the Central Locking System: The central locking system, fully known as the central control door lock, is an automotive accessory that allows remote opening and locking of doors without inserting the key into the lock. It consists of a door lock switch, an actuator, and a controller. 2. Basic Principle of Remote Control: A weak radio wave is emitted from the vicinity of the car owner, received by the car's antenna, and the signal code is identified by the electronic control unit (ECU). The system's actuator (motor or electromagnetic coil) then performs the locking or unlocking action. This system mainly comprises a transmitter and a receiver. 3. Functions: (1) Central Control: When the driver locks the door next to them, all other doors are simultaneously locked. The driver can open all doors via the door lock switch or open a single door individually. (2) Speed Control: When the vehicle reaches a certain speed, all doors automatically lock to prevent passengers from accidentally opening the doors by operating the door handles. (3) Individual Control: Besides the door next to the driver, other doors are equipped with separate spring lock switches, allowing independent control over the opening and locking of each door.

19

5

Share

What does terminal 31 mean in Volkswagen?

Volkswagen terminal 31 refers to the battery negative ground wire. Characteristics of Volkswagen circuit diagrams: In Volkswagen circuit diagrams, you often encounter connection points marked with numbers and letters, each with a fixed meaning. For example, the number 30 represents the power supply line from the battery positive terminal; the number 31 represents the battery negative ground wire; the number 15 represents the ignition power supply line from the ignition switch; the number 50 represents the starter power supply line when the ignition switch is in the start position; and the letter X represents the power supply line for high-capacity electrical equipment controlled by the ignition switch (from the load relay). Overall markings in Volkswagen circuit diagrams: Each wire is labeled with its color and cross-sectional area. The ends of the wires have terminal numbers or socket numbers indicating their connections. Color markings are represented by letters, with the following correspondences: ws=white; sw=black; ro=red; br=brown; gn=green; bl=blue; gr=gray; li=purple; ge=yellow. If a wire has two colors, it is marked with both color letters, such as ro/sw or se/ge. The cross-sectional area of the wire is indicated by a number above the wire color, in mm². For example, 4.0, 6.0, etc.

20

5

Share

How long does it take for a car to fill with water when submerged?

What is the issue with the Haval H6 air conditioning turning on automatically?

Where to Place the Jack for a Corolla?

What is the Regal in the United States?

Why did the Audi A3 suddenly go silent?

How to Solve the Random Jumping Issue of the Excelle's Central Locking System?

What does terminal 31 mean in Volkswagen?

What is the normal fuel consumption for the 10th-generation Civic?

Where is the OBD interface of Citroen C4L?

Where to find the 16-inch wheel data for Lavida?

How many tires should be replaced at once for a BMW 3 Series?