How Long After Passing C1 Subject 1 Can You Take Subject 2?

1 Answers
JulietteMarie
07/29/25 8:13pm
For a C1 driver's license, you can schedule the Subject 2 test online 10 days after passing Subject 1. According to the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses," the registration requirements for Subject 2 include completing 26 study hours: 2 hours of theoretical knowledge, 3 hours of simulated driving, and 21 hours of practical training. For a C1 driver's license, you can schedule the Subject 2 test online 10 days after passing Subject 1. Each Subject 2 test appointment allows for two attempts. If the first attempt is unsuccessful, you can retake the test for free once. If you do not attend the retest or fail the retest, the test session ends, and you can reschedule Subject 2 after 10 days. Within the validity period of the driver's learning permit, the number of Subject 2 test appointments must not exceed five. If the fifth attempt is still unsuccessful, the results of other previously passed subjects will be invalidated. To continue pursuing the driver's license, you must restart the process from Subject 1. Subject 2 test content includes: driving a motor vehicle to complete test items within a designated area; demonstrating mastery of driving skills; and assessing the ability to judge the spatial position of the vehicle. Subject 2 is also known as the small road test and includes five mandatory items: reverse parking, parallel parking, hill start and stop, right-angle turns, and curve driving. Subject 2 test precautions: After getting into the car, always adjust the seat and mirrors to a suitable position and state, and ensure the seatbelt is fastened. For parallel parking, remember to find the correct angle, turn the steering wheel quickly, react promptly, and coordinate with the car's speed. For hill starts, remember to engage the handbrake, activate the left turn signal when starting, release the handbrake, stabilize the clutch, and gradually release the clutch while pressing the accelerator to avoid stalling or rolling back. For right-angle turns, identify the turning point quickly and react accordingly, coordinating with the car's speed to prevent deviation. For curve driving (S-turns), slow down and proceed cautiously. Those with good driving instincts during practice may pass smoothly in one go. For reverse parking, control the speed carefully, identify reference points accurately, and make minor adjustments when observing deviations in the mirrors. The driver's license test consists of three subjects: Subject 1, Subject 2, and Subject 3. Subject 1 covers traffic safety laws, regulations, and related knowledge. Subject 2 is the field driving skills test. Subject 3 is divided into two parts: road driving skills and safety and civilized driving knowledge. The safety and civilized driving knowledge test is conducted after Subject 3, so it is commonly referred to as Subject 4. However, the official terminology (under the Ministry of Public Security's Order No. 123) does not include the term "Subject 4."
Was this review help?
16
5
Share
More Forum Discussions

Is the Daytime Running Light Displayed on the Dashboard?

Daytime running lights do not have an icon on the dashboard, and no indicator light will illuminate on the dashboard when they are turned on. Function of daytime running lights: They serve as a signal while driving, without providing illumination, making the vehicle more easily recognizable during daytime driving. When the car engine starts, the daytime running lights automatically turn on and gradually increase in brightness to attract the attention of other motor vehicles, non-motor vehicles, and pedestrians on the road. Definition of daytime running lights: There are generally two, with the outer one being the light switch. Daytime running lights, also known as DRLs, are installed on the front sides of the vehicle to signal its presence during the day. When the car engine starts, the daytime running lights automatically turn on and gradually increase in brightness to attract the attention of other motor vehicles, non-motor vehicles, and pedestrians on the road.
4
2
Share

What maintenance items are required for a car with over 50,000 kilometers?

Maintenance items required for a car with 50,000 kilometers: 1. Spark plugs: The replacement cycle depends on the material, generally ranging from 2 to 4 years; 2. Air filter: If it hasn't been replaced for a while, it should be replaced now; 3. Belts and chains: If the vehicle's engine uses a timing belt, it should be inspected or replaced at 50,000 kilometers. If the engine uses a timing chain, inspection is sufficient without replacement; 4. Engine oil and oil filter: Under high temperature and high pressure conditions in the engine, the shelf life of engine oil is significantly reduced, and its performance declines sharply. Over time, it fails to protect the engine effectively.
12
2
Share

Can the Kawasaki Z900 carry a passenger?

Kawasaki Z900 cannot carry a passenger. Motorcycle working principle: When the pedal is depressed, the mechanism pressurizes the spring, causing the outer edge of the spring to lift and separate the pressure plate from the friction plate. At this point, the friction plate and flywheel are no longer connected, so even if the engine continues to run, power will not be transmitted to the gearbox and wheels. This allows the rider to shift gears or come to a complete stop without stalling the engine. Power transmission: When the crankshaft speed is low, the two friction plates cannot contact the housing, preventing power transmission. At high crankshaft speeds, centrifugal force causes the friction plates to move outward and engage with the housing, enabling power transmission.
7
3
Share

What is the recommended speed for a new car during the break-in period?

For a new car during the break-in period, it is recommended to maintain a speed between 70 to 80 kilometers per hour, with the engine speed not exceeding 2,200 RPM. The break-in period for a new car is necessary because many components have not undergone prolonged coordinated operation after production. Although the car has undergone initial running-in, the surfaces of the parts are still relatively rough. During the break-in period, the following points should be noted: 1. Engine warm-up: When starting the car cold, it is best to wait until the coolant temperature reaches at least 40 degrees Celsius before driving; 2. Driving control: For a car in the break-in period, it is essential to control the driving speed and avoid high speeds; 3. Frequent gear changes: Do not use a single gear for extended periods. Start in a low gear and gradually shift to higher gears, driving progressively.
3
0
Share

What to Do When a Mercedes Key is Locked in the Trunk?

Choose to use a spare key or visit a 4S repair shop. The basic components of a remote key consist of the following two points: 1. Transmitter: Composed of a transmission switch, transmission antenna, integrated circuit, etc., it contains an identification code storage circuit and an amplitude modulation circuit, with a button-type lithium battery installed on the opposite side of the circuit. The transmission frequency uses radio waves, and pressing the transmission switch button once sends a signal once. 2. Receiver: After the transmitter sends an identification code using shortwave modulation, it is received by the car's shortwave antenna and enters the shortwave high-frequency amplification processor of the receiver's electronic control unit via a distributor for demodulation, where it is compared with the demodulator's identification code.
1
3
Share

How to Use the Lynk & Co 06 Dash Cam?

Before use, first insert the memory card. Press and hold the power button to turn it on or off. Open the Lynk & Co APP on your phone, go to 'Lynk & Co Services' – 'Dash Cam' to access functions like live recording, snapshot, emergency recording, viewing photos/videos, and settings. Details are as follows: 1. Live Recording: After successful device connection, click the play button on the main interface to start live recording. 2. Snapshot: Click the snapshot button on the interface to take a photo. The captured image will be displayed below after successful capture. 3. Emergency Recording: Click the emergency recording button to start recording. After the countdown completes, you can view the recording. Additionally, when abnormal conditions meet the set criteria, the dash cam will automatically activate emergency recording.
14
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.