How Far Can You Drive After the Fuel Tank Light Comes On?

1 Answers
Delaney
09/04/25 8:17am
When the fuel tank light comes on, you can generally drive for about 30 kilometers. There is no universal standard for how far you can drive after the fuel warning light illuminates, as different car models have varying ranges. You can find this specific value in your car's manual. Here are some important points to note when the fuel tank light comes on: 1. It is not recommended to wait until the fuel warning light comes on before refueling. Firstly, with low fuel levels, aggressive driving can affect the fuel pump's operation due to significant vehicle tilting. Secondly, after the fuel warning light comes on, there is no guarantee that you will find a gas station within the remaining range. Additionally, refueling only after the fuel warning light comes on is feasible only if you can find a gas station nearby; if the distance is too far, there is a risk of damaging the fuel pump and fuel level sensor. 2. Before going on a road trip, always plan your route in advance, identify gas station locations, and ensure you have sufficient fuel. If you do end up driving until the fuel warning light comes on, try to avoid sudden acceleration and braking, and turn off the air conditioning to prevent increased fuel consumption.
Was this review help?
4
3
Share
More Forum Discussions

What is the function of valve timing?

The function of valve timing is to coordinate with the operation of the piston and cylinder liner, regularly opening and closing the intake and exhaust valves. Valve timing refers to the opening and closing moments of the intake and exhaust valves and their duration, expressed in terms of crankshaft rotation angles. It is typically represented by a circular diagram. In a four-stroke engine, the intake valve opens when the crank is at top dead center and closes when the crank reaches bottom dead center; the exhaust valve opens when the crank is at bottom dead center and closes when it reaches top dead center. The intake and exhaust durations each occupy 180 degrees of crankshaft rotation. The purpose of advancing the intake valve opening is to ensure that the intake valve is fully open when the intake stroke begins, allowing fresh air to smoothly fill the cylinder. When the piston reaches bottom dead center, the pressure inside the cylinder is still lower than atmospheric pressure. During the initial stage of the compression stroke, when the piston moves upward at a slower speed, the inertia of the airflow and the pressure difference can still be utilized to continue the intake process. Therefore, delaying the closing of the intake valve slightly is beneficial for improving cylinder charging.
8
3
Share

What are the causes of brake noise in the Audi Q5?

Audi Q5 brake noise is caused by: 1. Corrosion of the brake disc or brake pads; 2. New brake pads; 3. Excessive wear of the brake disc and brake pads; 4. Incorrect installation or mismatched model of brake pads; 5. Use of inferior or overly hard brake pads; 6. Abnormal brake caliper or lack of brake fluid; 7. Presence of foreign objects between the brake drum or disc and the pads. Taking the 2020 Audi Q5 as an example, it belongs to the medium-sized SUV category, with body dimensions of: length 4753mm, width 1893mm, height 1659mm, wheelbase of 2908mm, fuel tank capacity of 73l, and a body weight of 1855kg.
19
4
Share

Where is the trunk opening button of the Tayron located?

The trunk opening button of the Tayron is located on the left front door interior trim panel, in the position of the main driver's compartment. Simply lift the button upwards with your hand, and the trunk lid will open. The trunk of the Volkswagen Tayron is generally flat with good practical dimensions: a depth of 900mm, a width of 1000mm, and a height of 740mm. The height of the trunk floor is almost the same as the outer edge, making it convenient for daily luggage handling. The Tayron comes in three length specifications: 4589mm, 4595mm, and 4590mm, with a width of 1860mm, a height of 1660mm, and a wheelbase of 2731mm.
11
2
Share

What are the correct steps for parking in Subject 2?

The correct steps for parking in Subject 2 are: 1. Observe the left and right rearview mirrors and the interior rearview mirror; 2. Turn your head to look at the right side of the vehicle and turn on the right turn signal; 3. Slow down and steer to the right; 4. Straighten the vehicle using the right-left-right method; 5. Park the vehicle and engage the handbrake; 6. Shift to neutral; 7. Release the clutch and turn off the engine to stop. Subject 2, also known as the small road test, is part of the motor vehicle driver's license assessment and is the abbreviation for the field driving skill test subject. The test items for small cars C1 and C2 include five mandatory tests: reversing into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and driving on a curve.
3
3
Share

What are the new physical requirements for a C1 driver's license?

All physical indicators must meet the requirements. 1. Height: Applicants for large buses, tractors, city buses, large trucks, or trolleybuses must be at least 155 cm tall. Applicants for medium-sized buses must be at least 150 cm tall; 2. Vision: For large buses, tractors, city buses, medium-sized buses, large trucks, trolleybuses, or trams, uncorrected or corrected visual acuity must reach 5.0 or above on the logarithmic visual acuity chart. For other vehicle types, uncorrected or corrected visual acuity must reach 4.9 or above; 3. Color vision: No red-green color blindness; 4. Hearing: Must be able to distinguish the direction of sound at 50 cm from a tuning fork in each ear. Applicants with hearing impairments who can meet the above conditions with hearing aids may apply for a driver's license for small cars or small automatic transmission cars; 5. Upper limbs: Both thumbs must be intact, and each hand must have at least three other fingers intact, with normal limb and finger movement. However, applicants with missing fingertip segments or a missing right thumb may apply for a driver's license for small cars or small automatic transmission cars; 6. Lower limbs: Both lower limbs must be intact with normal movement function, and the length difference must not exceed 5 cm. However, applicants with a missing or non-functional left lower limb may apply for a driver's license for small automatic transmission cars. Applicants with missing or non-functional right lower limbs or both lower limbs but who can sit independently may apply for a driver's license for small automatic transmission passenger cars designated for the disabled; 7. Trunk and neck: No movement dysfunction.
15
5
Share

What is the problem with the car lights flashing?

The reasons for car lights flashing are: 1. Poor circuit contact; 2. Stabilizer failure; 3. Problems with the bulb or high-voltage pack. The maintenance methods for car headlights are: 1. Regularly check the sealing of the headlights. If the sealing ring between the diffuser lens and the reflector is damaged, replace it promptly; 2. Clean the reflector regularly. If it turns black and the light intensity decreases, replace it; 3. Regularly clean dust and stains from the bulb. The standards for adjusting car headlights are: 1. Drive the car onto a flat and open road; 2. Turn on the car headlights and adjust the low-beam light spot to about 30m from the car, ensuring the two light spots overlap; 3. Adjust the high-beam light spot to be parallel to the ground.
6
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.