Do I need to bring my ID card for practicing Subject 2?

What are the effects of a clogged fuel tank vent hole?

Automatic transmission vehicles may downshift, experience sluggish acceleration, and produce abnormal noises. Relevant information is as follows: 1. Automatic transmission vehicles may downshift: When the exhaust pipe is clogged, the engine power of an automatic transmission vehicle will decrease. Typically, when the driver wants to accelerate after reaching a certain gear, they will press the accelerator. If there is no response, they may press it harder, but this usually does not result in actual acceleration and may instead cause the vehicle to downshift. This is due to the clogged exhaust pipe. 2. Sluggish acceleration: When attempting to accelerate, the vehicle may feel underpowered. This lack of power is often caused by incomplete combustion in the engine, which reduces power output. The root cause of incomplete combustion is usually a clogged exhaust pipe. 3. Abnormal noises: When there is an issue with the vehicle's exhaust pipe, abnormal noises may occur. These noises are typically a rattling sound, distinct from other types of abnormal noises. Additionally, abnormal noises from the exhaust system may be accompanied by excessive exhaust emissions. If left unaddressed for a long time, this can potentially damage other components of the vehicle.

9

0

Share

What are the test items for Driving Test Subject 3?

Subject 3 consists of a total of 16 test items: light simulation, preparation for getting on the car, starting, driving straight, changing lanes, passing intersections, passing crosswalks, passing school zones, passing bus stops, meeting vehicles, overtaking, making U-turns, operating gear shifting (acceleration and deceleration), turning left at intersections, turning right at intersections, and parking by the roadside. Additional related precautions are as follows: 1. When turning on the turn signal, note that the turn signal must be on for 3 seconds or mentally count to 3 before turning the steering wheel. 2. When driving straight, pay attention to the matching of gear and speed. The allowable range for first gear is 0~20, and the appropriate time to shift to second gear is between 15~20; the allowable range for second gear is 10~30, and the appropriate time to shift to third gear is between 25~30; the allowable range for third gear is 20~40, and the appropriate time to shift to fourth gear is between 35~40. Note that during the test, third gear must never exceed 40, otherwise it will be considered as "gear and speed mismatch" and result in a 10-point deduction. The allowable range for fourth gear is 30~50, and the appropriate time to shift to fifth gear is between 45~50.

9

1

Share

What to Check Before a Long-Distance Car Trip?

Before embarking on a long-distance car trip, the following items should be checked: 1. Oil and fluid inspection. Oils include engine oil, transmission fluid, power steering fluid, brake fluid, and fuel. Fluids include coolant and windshield washer fluid. Check if the coolant is low and if there are any leaks. If leaks are found, repair them promptly; if not, top up to the marked level. Fill the windshield washer fluid reservoir to full. 2. Brake pads and tire inspection. Check the thickness of the front and rear brake pads to see if they need replacement. For tires, first inspect the appearance of all four tires for cracks, scratches, bulges, or punctures. Then check if the tire pressure is adequate. For vehicles without a tire pressure monitoring system, it's best to drive to a tire service point to check the pressure and address any deficiencies. 3. Light inspection. This includes both front and rear lights. 4. Chassis inspection. Check for loose or noisy suspension components, such as control arms and ball joints, and ensure there are no safety issues like loose steering linkage. 5. On-board tool inspection. On-board tools include a warning triangle, fire extinguisher, and tire wrench. A warning triangle and fire extinguisher not only serve critical functions in emergencies but also help avoid penalties during routine traffic police checks. Ensure the fire extinguisher is within its validity period.

17

4

Share

What is the method for cleaning car headlights?

The method for cleaning car headlights is as follows: 1. Clean surface dust: Wipe the headlights with a cloth as thoroughly as possible. 2. Cover the edge areas of the headlights: Use tape to cover the edge areas of the headlights. Some cars may only have partial fogging or hazing, so you can also cover areas that do not need repair to avoid unnecessary scratches. 3. Initial sanding: Wipe the headlights with a cloth as thoroughly as possible. Soak a piece of 1000-grit sandpaper in cold water for 10 minutes, then evenly sand the headlight housing, moving back and forth in one direction while keeping the surface wet. Apply moderate pressure to avoid damaging the surrounding paint or trim. 4. Secondary sanding: Repeat the above process with 1500-grit sandpaper, but sand in a different direction (if the first sanding was vertical, this time sand horizontally). Continue to keep the sandpaper wet while sanding the entire area. After wiping clean, repeat the process multiple times with 2000-grit, 2500-grit, and 3000-grit sandpaper, each time sanding at a right angle to the previous direction. 5. Apply polish: Apply polish to the plastic housing and polish in a circular motion for about 10 minutes. Be mindful of the pressure to avoid removing the car paint. Continue until the surface regains its mirror-like shine and looks as good as new.

2

4

Share

How to Wash a Car Cleanly?

Washing a car with a car wash sponge, car wash solution, and a portable car washer can achieve a thorough clean. Below are the key points to pay attention to when washing a car: 1. Washing environment: The car should be washed when the body is cool, in a place without wind and direct sunlight, using a towel or sponge for cleaning. 2. Sequence: The best order for washing is from the roof, hood, to the sides, moving around the car in a consistent direction for better dirt removal. Extended tips: 1. The waxing sequence is the same as washing: Waxing is best done when the car body is cool and must be done after washing. The waxing sequence is the same as washing, from the top of the car downward. 2. Car washing method: When cleaning the interior, remove and wash the floor mats, then let them dry in a shaded area. Use interior cleaner and a cloth to wipe the inside of the car, starting from the interior roof, doors, steering wheel, gear shift, and audio panel, moving from top to bottom. For dirt on plastic or leather surfaces or embedded in textures, use a small soft brush dipped in cleaner. Also, ensure the cloth used for the interior is separate from the one used for the exterior to avoid contaminating the inside of the car.

2

4

Share

What Could Be the Reason for Feeling Less Power After Changing Spark Plugs?

The reasons for feeling less power after changing spark plugs may include: The spark plugs were not tightened properly; The replaced spark plugs are of the wrong model; There is an issue with the ignition coil. Effects of damaged spark plugs: If the spark plugs are damaged, it can directly cause various problems such as leakage in the vehicle's ignition system, increased fuel consumption, and reduced power. The most significant issue is difficulty in ignition, affecting the normal use of the vehicle. Severe erosion of the spark plugs, scarring at the top, damage, or melting and erosion of the electrodes indicate that the spark plugs are damaged and should be replaced. How to determine if spark plugs are damaged: Remove the spark plugs and observe their appearance to assess their condition. Normal spark plugs have an insulator skirt and electrodes that appear gray-white, gray-yellow, or light brown. A properly functioning spark plug has a reddish-brown insulator skirt, with an electrode gap between 0.8-0.9mm and no signs of electrode burn. If the spark plugs are covered in oil or deposits but are not damaged, they can continue to be used after cleaning off the oil and deposits. If the spark plugs are severely damaged, showing signs such as scarring, black streaks, cracks, or melted electrodes, the cause of the damage should be identified. After troubleshooting, replace the spark plugs with new ones. Additionally, if the spark plugs appear black as if smoked, it indicates that the wrong heat range was selected or that the mixture is too rich, with oil seeping up.

20

1

Share

Do I need to bring my ID card for practicing Subject 2?

What are the effects of a clogged fuel tank vent hole?

What are the test items for Driving Test Subject 3?

What to Check Before a Long-Distance Car Trip?

What is the method for cleaning car headlights?

How to Wash a Car Cleanly?

What Could Be the Reason for Feeling Less Power After Changing Spark Plugs?

Why Does a Fart Smell Suddenly Appear in the Car?

How to Switch Between Gasoline and Electric Modes?

Can I Claim Insurance for a Flat Tire?

What is the difference between the two-wheel drive and four-wheel drive versions of the Avancier?