···
Log in / Register

Can You Still Drive with 1.7bar Tire Pressure?

1Answers
VonKennedy
07/28/2025, 11:35:59 PM

Tire pressure of 1.7bar is too low to continue driving. Excessively low tire pressure can cause severe deformation of the tire sidewall, damage the cord layer, and lead to a tire blowout. Hazards of low tire pressure: Increased friction coefficient with the road surface, leading to higher fuel consumption; Causes heavy steering and easy deviation, which are unfavorable factors for driving safety; Increases the movement of various parts of the tire, causing abnormal heating due to excessive rolling; Reduces the functionality of the cord and rubber, leading to delamination or cord breakage, excessive friction with the rim, resulting in damage to the bead area and abnormal wear; Multiplies the friction between the tire and the ground, sharply increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may cause a tire blowout; Increases tire body deformation, making the tire sidewall prone to cracks, and generates flexing motion, leading to excessive heat, accelerating rubber aging, cord layer fatigue, and cord breakage. It also increases the tire's contact area with the ground, accelerating shoulder wear. Solutions for insufficient tire pressure: If no damage is visible, simply inflate to normal tire pressure and reset the tire pressure system; If a puncture is found during inspection, drive to a tire shop promptly for repair, then reinflate; If the tire pressure warning reappears after inflation without any puncture, it may be due to air leakage caused by rim deformation. It is recommended to check the rim and replace it if necessary.

Was this review help?
116
Share
More Q&A

Do You Need to Press the Clutch in First Gear When Going Uphill?

You do not need to press the clutch in first gear when going uphill. Here is the relevant information: Clutch: The clutch is located inside the flywheel housing between the engine and the transmission. The clutch assembly is fixed to the rear plane of the flywheel with screws, and the output shaft of the clutch is the input shaft of the transmission. During driving, the driver can press or release the clutch pedal as needed to temporarily disconnect or gradually engage the engine and the transmission, thereby cutting off or transmitting the power from the engine to the transmission. The clutch is a common component in mechanical transmissions, allowing the drivetrain to be disconnected or engaged at any time.
109
Share

How to resolve ABS preventing engine start?

ABS preventing engine start can be resolved by: disconnecting the ABS power supply in the engine compartment. The reasons for the ABS warning light illuminating are: 1. Faulty wheel speed sensor, ABS wiring, ABS pressure control solenoid valve, or ABS computer; 2. Insufficient brake fluid; 3. Dirty ABS sensor. ABS indicates a malfunction in the vehicle's anti-lock braking system. Since this system is crucial for vehicle safety, any issues should be promptly repaired to avoid affecting normal vehicle operation. The ABS system in a vehicle enhances driving safety and improves the safety coefficient during emergency braking.
116
Share

How to Check the Remaining Fuel Level in a BMW?

Method to check the remaining fuel level in a BMW: The dashboard has a fuel gauge, and observing how many bars remain will indicate the remaining fuel level. Fueling precautions: Do not wait until the yellow light comes on to refuel. Before driving, check the fuel gauge and calculate whether you need to refuel during the trip based on the distance and the gauge's reading. You can refuel in advance. Taking the BMW X5 as an example: The BMW X5 is a mid-to-large-sized SUV under BMW. The vehicle's length, width, and height are 4930 mm, 2004 mm, and 1776 mm respectively, with a wheelbase of 2975 mm. In terms of suspension, the BMW X5 features a double-wishbone independent front suspension and a multi-link independent rear suspension.
109
Share

How to Quickly Remove Old Car Film?

To quickly remove old car film, first use a utility knife to make an opening at any part of the car body, then peel off the film with appropriate force. High-quality car film can be removed directly, while low-quality film may leave some adhesive residue after removal. Methods to remove adhesive residue include: 1. Using vinegar; 2. Using essential balm; 3. Using alcohol. Car film is applied to the vehicle's windows, including the front and rear windshields, side windows, and sunroof, as a thin layer of material also known as solar film or heat-insulating film. Its main functions are to block ultraviolet rays, reduce heat, prevent injuries from shattered glass, reduce glare, and, due to the one-way visibility feature of the solar film, protect personal privacy.
118
Share

Can a Small Spoiler Pass the Annual Vehicle Inspection?

Installing a small spoiler cannot normally pass the annual vehicle inspection. Modifications such as adding spoilers, extensive body kits, or altering the exhaust system are generally not permitted. During the annual inspection, the vehicle is checked for any modifications, alterations, or transformations. The inspection verifies whether the vehicle's registration details, license plate, and vehicle records match the actual condition of the car and if any changes have been made, including whether the necessary approval and modification procedures have been completed. The vehicle must regularly pass emissions testing, as well as inspections for exterior appearance, lights, brakes, and chassis, and must have no outstanding traffic violations to receive the inspection compliance sticker. Any unresolved traffic violations in the vehicle's usage location must be addressed beforehand.
104
Share

How to Set the Beep Sound When Locking the Car?

The method to set the beep sound when locking the car is as follows: 1. Step on the brake pedal to start the vehicle, shift the gear to the P position, and pull up the handbrake. 2. Close all four doors and the trunk of the vehicle. 3. Press the mute button on the key inside the car, and the vehicle will emit a beep sound when locking the car next time. The reasons why there is no beep sound after locking the car are as follows: 1. Accidentally pressing the mute button on the key. When the mute button is pressed, the vehicle will not emit any beep sound whether unlocking or locking. At this time, simply press the mute button on the key again to enable the beep sound when locking the car. 2. The beeper is damaged. If the vehicle still does not emit a beep sound after pressing the mute button, it indicates that the beeper is damaged, and you can only go to a 4S store for repair.
117
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.