Can New Energy Vehicles Get Blue License Plates?

2 Answers
Shelly
07/28/25 10:19pm
New energy vehicles cannot get blue license plates; they must use green license plates, which are special plates designated for new energy vehicles, with green symbolizing environmental protection. Types of new energy vehicles include: pure electric vehicles, plug-in hybrid electric vehicles, and fuel cell vehicles. Characteristics of new energy vehicles: 1. They use natural gas, petroleum gas, hydrogen, or electricity as power sources, saving fuel energy; 2. They reduce exhaust emissions, produce no tailpipe pollution (hydrogen vehicles emit only water, causing no environmental harm); 3. They employ new technologies and structures for higher efficiency; 4. They operate with low noise.
Was this review help?
3
0
Share
DelIker
08/12/25 2:51am
I've been following automotive policies for quite some time, and regarding new energy vehicles getting blue license plates, it's actually not possible. According to Chinese regulations, blue plates are exclusively for traditional fuel-powered vehicles, like gasoline or diesel cars, while new energy vehicles, including pure electric and plug-in hybrids, must all use green license plates. This rule has been in effect since 2016, aiming to promote environmentally friendly vehicles and reduce pollution. If you buy a new energy vehicle and go to the DMV to register it, the staff will definitely tell you that you can only choose a green plate, with no option for a blue one. The advantage is that green-plated vehicles are exempt from traffic restrictions in many cities and can also save a significant amount of money by being exempt from purchase tax. I think this is very cost-effective for ordinary families buying cars, especially in big cities with strict traffic restrictions. If you want peace of mind, check the local subsidy policies before purchasing a car so you can maximize the benefits.
Was this review help?
1
5
Share
Expand All
More Forum Discussions

Toyota E'Z Dimensions?

The body dimensions of the E'Z are 4450x1790x1640mm, with a wheelbase of 2780mm. The specific introduction of Toyota E'Z is as follows: 1. E'Z Introduction: The E'Z is a stylish and versatile family sedan meticulously crafted by GAC Toyota according to mid-to-high-end car standards. The current model offers 6 variants with two displacement options: 1.6L and 1.8L. 2. Engine Specifications: The 1.6L engine of the E'Z delivers a maximum output power of 90kW and a maximum torque of 154Nm; the 1.8L engine provides a maximum output power of 103kW and a maximum torque of 173Nm; the 2.0L engine achieves a maximum output power of 107kW and a maximum torque of 187Nm.
1
2
Share

What are the items in the Subject 3 road test?

Here is a detailed introduction to the 16 items in the Subject 2 road test: 1. Preparation before starting: After hearing the voice prompt "Begin the preparation for starting the vehicle," walk around the vehicle once, then get in and fasten the seatbelt. 2. Night driving: After hearing the voice prompt "Now simulating night driving, approaching an intersection (turn on low beam), entering an unlit road section (turn on high beam), road ahead is well-lit (turn on low beam), approaching an intersection without traffic signals (sound the horn), temporary parking by the roadside (turn on hazard lights)." 3. Starting: After hearing the voice prompt "Begin starting the vehicle (turn on left turn signal for more than 3 seconds, sound the horn, and start)," start the vehicle and drive for 10 meters. 4. Straight-line driving: After hearing the voice prompt "Begin straight-line driving test," adjust the vehicle within the lane without crossing the lane markings, and drive straight for 100 meters. 5. Lane change: After hearing the voice prompt "Begin lane change test," turn on the left turn signal (for more than 3 seconds), change lanes, and drive for 100 meters. 6. Overtaking: After hearing the voice prompt "Begin overtaking test," turn on the left turn signal (for more than 3 seconds), move to the overtaking lane, drive for more than 20 meters, then return to the original lane. The overtaking distance is 200 meters. 7. Meeting oncoming traffic: After hearing the voice prompt "Begin meeting oncoming traffic test," keep the left side of the vehicle more than 30 cm from the double yellow lines, maintain a speed below 30 km/h, and drive for 70 meters. 8. Gear shifting operation: After hearing the voice prompt "Begin gear shifting operation test," shift up from 2nd gear to 4th gear in sequence, then shift down from 4th gear to 2nd gear in sequence. Fully release the clutch after each gear shift and maintain straight-line driving. The speed limits are: 1st gear up to 20 km/h, 2nd gear up to 27 km/h, 3rd gear up to 37 km/h, 4th gear up to 47 km/h, 5th gear minimum 30 km/h. The gear shifting operation distance is 250 meters. 9. Straight through an intersection: After hearing the voice prompt "Begin straight through an intersection test," maintain a speed below 30 km/h, keep the vehicle in a straight-line driving state, and proceed straight through the intersection without crossing the lane markings. 10. Left turn at an intersection: After hearing the voice prompt "Begin left turn at an intersection test," enter the left-turn lane, turn on the left turn signal (for more than 3 seconds), maintain a speed below 30 km/h, and make a left turn through the intersection without crossing the lane markings. 11. Right turn at an intersection: After hearing the voice prompt "Begin right turn at an intersection test," enter the right-turn lane, turn on the right turn signal (for more than 3 seconds), maintain a speed below 30 km/h, and make a right turn through the intersection without crossing the lane markings. 12. Passing a crosswalk: After hearing the voice prompt "Begin passing a crosswalk test," maintain a speed below 30 km/h, keep the vehicle in a straight-line driving state, and proceed straight through without crossing the lane markings. 13. Passing a bus stop: After hearing the voice prompt "Begin passing a bus stop test," maintain a speed below 30 km/h, keep the vehicle in a straight-line driving state, and proceed straight for 50 meters without crossing the lane markings. 14. Passing a school zone: After hearing the voice prompt "Begin passing a school zone test," maintain a speed below 30 km/h, keep the vehicle in a straight-line driving state, and proceed straight for 50 meters without crossing the lane markings. 15. U-turn: After hearing the voice prompt "Begin U-turn test," turn on the left turn signal (for more than 3 seconds) in the overtaking lane, and begin the U-turn. 16. Pulling over: After hearing the voice prompt "Begin pulling over test," turn on the right turn signal (for more than 3 seconds), pull over, and keep the right side of the vehicle within 30 cm of the curb. A distance greater than 30 cm will result in a 10-point deduction. The pulling over distance is 100 meters. Shift to neutral, engage the handbrake, release the foot brake, unfasten the seatbelt, and open and close the door. Driving in 1st gear continuously must not exceed 100 meters, and driving on lane markings must not exceed 60 meters.
10
4
Share

What Causes the Classic Focus to Shake During Acceleration?

Classic Focus shaking during acceleration can be attributed to the following reasons: 1. Damaged engine mounts: When the engine mounts are damaged, their noise and vibration reduction functions are compromised, especially noticeable during acceleration and deceleration with pronounced shaking and noise. 2. Unbalanced wheels: This can also lead to shaking during acceleration and may cause the steering wheel to vibrate. 3. Excessive throttle carbon buildup: Carbon deposits in the throttle can lead to various minor car issues, with acceleration shaking being one of them. 4. Faulty spark plugs: In the engine cylinders, the air-fuel mixture requires an electric spark to ignite. If the spark is weak or absent, it can lead to a misfire, disrupting the engine's balance and causing the vehicle to shake and produce noise. 5. Clutch slippage: Whether it's a manual transmission or a dual-clutch transmission, power is transmitted by clamping the clutch plates. When the clutch slips, it can cause the engine to shake as if in a semi-engaged state, or in severe cases, result in jerking or even stalling.
13
4
Share

How to Replace the Battery in a Mercedes-Benz M-Class Key?

Mercedes-Benz M-Class key battery replacement steps are as follows: 1. Flip open the tab at the rear end of the key to remove the mechanical key: Insert the mechanical key into the side slot of the key, press the internal gray button, and with the other hand push the rear end of the key upwards. When a gap appears, the mechanical key can be removed. 2. Then use your hand to take out the rear end: You can now replace the battery. 3. After installing the new battery: Reinsert the key holder, and the key battery replacement is complete. The lifespan of a Mercedes-Benz key battery is generally two years, while the original factory battery can last up to six years. When the key battery is low, the Mercedes-Benz vehicle will provide two types of alerts. The first is when you press the ignition switch, the dashboard will display a message to replace the key battery. The second is when you press the lock or unlock button on the key, the indicator light on the key will dim or not light up.
11
0
Share

Which is better for the Buick Excelle, 5w30 or 5w40 engine oil?

For the Buick Excelle, it is recommended to use 5w30 engine oil. The details about engine oil are as follows: 1. According to the car maintenance manual: 5w30 is the recommended engine oil for the Buick Excelle. The 5w30 engine oil has better fluidity and superior low-temperature anti-wear performance. 2. Low-viscosity engine oil has become mainstream: Only Volkswagen vehicles still require 40 engine oil due to piston tension issues. 3. Engine oil grades: They are classified by quality grade and viscosity grade. Engine oil for gasoline engines is usually denoted by the letter "S", while diesel engine oil is denoted by the letter "C". 4. Composition of engine oil: It consists of base oil and additives, where the base oil is the main component of the lubricant, determining its basic properties, and additives can improve the shortcomings of the base oil.
1
5
Share

How Many Liters of Engine Oil Does a Focus Need?

For a Focus, 3.7-3.8 liters of engine oil is sufficient, but it's essential to check the oil dipstick during the oil change process. Here are some key points about changing engine oil: 1. Choose engine oil based on the engine's requirements: There's no need to use overly advanced oil for engines with lower requirements, nor should you use lower-grade oil in engines with higher demands. 2. Opt for multi-grade oil when possible: Multi-grade oil is economical, long-lasting, and efficient, providing excellent protection for the engine. Due to its characteristics, multi-grade oil may appear darker sooner or show lower oil pressure compared to conventional oil, which is normal. 3. Some domestic brand engine oils are of quite good quality: They are significantly cheaper than imported counterparts and can be used with confidence. 4. If the engine is in good condition and the seasonal temperature is low, it's advisable to use lower-viscosity oil to ensure smooth oil flow. In high-temperature seasons or when the engine is severely worn, higher-viscosity oil helps form a protective oil film and reduces engine wear.
19
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.