Can Keyless Entry Be Installed Later?

2 Answers
EmilianoFitz
07/24/25 10:14am
Keyless entry can be installed. The keyless start system allows the vehicle to be started without turning a key. Simply keep the key in your bag or pocket, press the button inside the car, or turn the ignition knob to start the engine, making it more convenient and significantly enhancing the sense of luxury and technology. In addition to being user-friendly, the keyless start system also greatly improves vehicle security and safety. 1. Introduction: The keyless start system utilizes advanced Radio Frequency Identification (RFID) technology, automatically locking and unlocking the doors via the chip in the smart card carried by the owner. When the driver approaches the vehicle within a certain distance, the door locks will automatically open and disable the anti-theft system. When the driver leaves the vehicle, the door locks will automatically lock and activate the anti-theft system. 2. Anti-theft Performance: The electronic key's chip uses fourth-generation RFID technology, making it nearly impossible to duplicate the encryption system. Moreover, without proper documentation, the official service will not provide a replacement key.
Was this review help?
17
4
Share
JamesonAnn
08/11/25 5:24am
I just installed a keyless entry system in my car, and the experience is amazing! It's mainly achieved through aftermarket kits, which you can purchase online and have professionally installed at a shop. The process is actually quite simple: first, remove the original door handle and replace it with a sensor-equipped one, then connect it to the vehicle's computer module and pair it with the remote key. However, you must choose a kit compatible with your car model to avoid issues. For my older car, I used a third-party brand, costing only 800 yuan, which was quite cost-effective. The biggest benefit is the convenience—now, I just need to walk up to the car with the key in my pocket, and it unlocks automatically, saving time and effort. I also picked up some knowledge about vehicle electronics, like how this system integrates with the factory anti-theft function. If installed improperly, it might interfere with the anti-theft system, so I recommend not DIY-ing it and instead finding a reputable shop. Overall, retrofitting is completely feasible—it just takes some upfront research, but it definitely enhances daily driving convenience.
Was this review help?
7
1
Share
Expand All
More Forum Discussions

What is the ground clearance of the Touran?

The ground clearance of the Touran is 100mm. The minimum ground clearance of the Touran refers to the distance between the lowest point (excluding the wheels) and the supporting plane, which indicates the vehicle's ability to pass over obstacles such as rocks and tree stumps without collision. A higher ground clearance of the Touran improves its off-road capability, but if the ground clearance is too high, the stability at high speeds may decrease. The Touran features a front MacPherson independent suspension and a rear four-link independent suspension. It is equipped with a 1.4T turbocharged engine, delivering a maximum horsepower of 150 PS, a maximum power of 110 kW, and a maximum torque of 250 Nm, paired with a 7-speed dual-clutch transmission. The Touran's body dimensions are 4527mm in length, 1829mm in width, 1659mm in height, and a wheelbase of 2291mm. Generally, the ground clearance of sedans ranges between 110mm and 150mm, while SUVs have a ground clearance between 200mm and 250mm. However, the ground clearance of the Touran is not static; it depends on the load condition. Therefore, changes in ground clearance should be considered based on the Touran's load variations. When selecting a vehicle, ground clearance can be one of the reference factors. The choice should depend on the vehicle's intended use and the road conditions. For urban driving with well-paved roads, a vehicle with lower ground clearance can enhance stability and comfort. For frequent travel to remote areas or driving on rough terrain, a vehicle with higher ground clearance is advisable to improve off-road performance and avoid damage to the undercarriage.
18
1
Share

What Octane Gasoline Should the Fit Use?

The Fit should use 92-octane gasoline, as this is the recommended fuel grade specified in the vehicle's official owner's manual. In addition to checking the owner's manual for the appropriate gasoline grade, you can also find this information on the fuel filler cap, which will be clearly marked. Typically, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with a compression ratio between 8.6-9.9 should use 92-octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95-octane gasoline. For higher compression ratios, 98-octane gasoline is recommended. However, with the advent of new technologies, the compression ratio alone cannot determine the appropriate gasoline grade. Engines with high compression ratios can also be tuned to use lower-octane gasoline due to other influencing factors such as ignition timing, turbocharging technology, and Atkinson cycle technology. Generally, higher-octane gasoline has a higher octane rating and better anti-knock properties. For example, 92-octane gasoline contains 92% isooctane and 8% n-heptane, while 95-octane gasoline contains 95% isooctane and 5% n-heptane. If the Fit occasionally uses the wrong gasoline grade, simply switch back to the correct grade after the current tank is used up. However, prolonged use of the wrong gasoline grade can have the following effects: For vehicles designed for lower-octane gasoline, using a higher-octane grade will not cause damage, but the increased octane rating can alter the fuel's ignition point, leading to delayed combustion in the engine. This results in reduced engine power and thermal efficiency, manifesting as poorer performance. For vehicles designed for higher-octane gasoline, using a lower-octane grade can cause engine knocking. The significantly lower octane rating lowers the fuel's ignition point, causing premature ignition during the compression stroke. If combustion occurs before the spark plug fires, resistance is created during the upward stroke. This resistance makes the engine run very unevenly. Mild knocking may only increase noise without significant engine damage, but noticeable knocking indicates severe engine conditions. The vibrations not only affect driving stability but can also cause abnormal wear on pistons and cylinders, potentially leading to cylinder scoring in severe cases.
3
3
Share

What is the tire size of the K5?

The K5 has two tire sizes: 235/45R18 and 215/55R17. In 235/45R18, the first number 235 represents the tire width of 235MM, 45 indicates the aspect ratio of the tire cross-section is 45%, meaning the section height is 45% of the width, 18 stands for the rim diameter of 18 inches, and the middle letter "R" denotes a radial tire. In 215/55R17, the first number 215 represents the tire width of 215MM, 55 indicates the aspect ratio of the tire cross-section is 55%, meaning the section height is 55% of the width, 17 stands for the rim diameter of 17 inches, and the middle letter "R" denotes a radial tire. The K5 series uses Hankook OPTIMO-H426 as its tire brand and model. The spare tire is a non-full-size one. If you want to replace the tires yourself, you can follow these steps: Take out the spare tire and jack, place the jack under the vehicle frame of the tire to be replaced, ensuring the jack touches the metal part of the frame; Raise the jack until it supports the car, the jack should be under the vehicle, check and ensure the jack is at a right angle to the ground; Remove the hubcap, loosen the nuts counterclockwise, do not completely loosen them, just enough to eliminate resistance, when loosening the nuts for the first time, keeping the tire on the ground ensures that the nuts turn rather than the tire; Turn the nuts counterclockwise until they are loose, repeat this step for all lug nuts, completely remove the nuts; Place the new tire on the hub, carefully align the tire rim with the wheel bolts, install the lug nuts, tighten the nuts by hand until all nuts are concealed, at this point the tire replacement is complete. In addition to the model, the tire also has the following common data marked on it: Tire cord material: represented by Chinese pinyin, such as M-cotton cord, R-rayon cord, N-nylon cord, G-steel cord, ZG-steel radial cord tire. Speed rating: indicates the maximum speed at which the tire can carry the specified load under specified conditions. Letters A to Z represent the certified speed ratings of the tire from 4.8km/h to 300km/h. Common speed ratings include: Q: 160km/h; H: 210km/h; V: 240km/h; W: 270km/h; Y: 300km/h; Rim specification: indicates the rim specification compatible with the tire. For practical use, such as "Standard rim 5.00F".
2
3
Share

What is the maintenance interval for the Hyundai Elantra?

Modern Elantra maintenance cycle is 5000 kilometers maintenance once, if you change the full synthetic oil can be 10,000 kilometers maintenance. The engine of the modern Elantra is divided into two types: naturally aspirated engine and turbocharged engine. The turbocharged engine can use full synthetic oil, which has better fluidity and viscosity, which is beneficial to reduce engine wear during rapid acceleration and play a better lubrication role. The oil change cycle corresponds to the oil category, mineral oil and synthetic oil are different, both have two index limits of time and mileage, whichever comes first, and the oil should be replaced together with the oil filter.
1
2
Share

What are the tips for cleaning an oxygen sensor?

Tips for cleaning an oxygen sensor: 1. Remove the oxygen sensor from the car; 2. Prepare a cleaning solution, typically by dissolving ferric chloride in water and then adding hydrochloric acid to mix; 3. Soak the oxygen sensor in the prepared solution for about 10 to 15 minutes; 4. After soaking, wipe it clean with a clean cloth. When the oxygen sensor turns white, it indicates the cleaning is complete. The oxygen sensor is a sensing component installed on the exhaust pipe of a car engine. It detects the gas ratio in the exhaust and feeds the information back to the car's onboard computer, allowing the vehicle to assess its condition and achieve an optimal driving state.
8
0
Share

How many years without vehicle inspection will lead to license plate cancellation?

3 years without vehicle inspection will lead to license plate cancellation; for new cars, 6 years without inspection will result in license plate cancellation. Different vehicle types have varying annual inspection schedules. Small and mini non-commercial passenger vehicles require inspection every 2 years within the first 6 years; annually after exceeding 6 years; and every 6 months after exceeding 15 years. Vehicle annual inspection refers to mandatory testing for all vehicles that have obtained formal license plates and registration certificates, equivalent to an annual physical examination for vehicles according to motor vehicle operational safety technical standards. Vehicle inspections can promptly eliminate potential safety hazards, encourage enhanced vehicle maintenance, and reduce traffic accidents.
19
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.