Can I Schedule the Subject Three Test After Failing Subject Two?

1 Answers
ColtonFitz
07/30/25 5:43am
You can schedule the Subject Three test after failing Subject Two. However, there are two prerequisites for scheduling Subject Three: 1. Training Hours: You must complete all the required training hours for Subject Three. 2. Mock Test: You are required to complete a two-hour mock test for Subject Three at the driving school. More relevant information is as follows: Notes: Because the driving school has timed surveillance cameras that capture images, the monitoring information will be transmitted to the internet service platform of the local provincial traffic police. Only after the website updates the training hours can you schedule the Subject Three test. If both conditions are met, you can directly schedule the Subject Three test, which can also save time. After failing Subject Two, you must wait 10 days before you can schedule the test on the website.
Was this review help?
3
3
Share
More Forum Discussions

What are the symptoms of a damaged exhaust check valve?

When the exhaust check valve is damaged, symptoms such as the engine warning light illuminating, difficulty starting, engine shaking, unstable idle, weak acceleration, and failure to meet emission standards may occur. Below is an introduction to the impacts of a damaged exhaust check valve: 1. After the exhaust valve is damaged, it cannot control the amount of exhaust gas recirculation. Excessive exhaust gas participating in recirculation will affect the ignition and performance of the air-fuel mixture, thereby impacting the engine's power, especially during idle, low speed, light load, and when the engine is cold. The recirculated exhaust gas will significantly affect engine performance. 2. A damaged exhaust valve can lead to the car burning oil, with severe blue smoke from the tailpipe.
17
5
Share

What does it mean when the cruise control light is on?

Cruise control light on indicates that the cruise control function is in standby mode, meaning the automatic cruise is activated. Here is an introduction to the automatic cruise function: 1. The car cruise control is used to maintain a constant speed for the vehicle. Once the car is set to cruise mode, the engine's fuel supply is controlled by the computer, which continuously adjusts the fuel supply based on road conditions and the vehicle's driving resistance to maintain the set speed without the need to operate the throttle. 2. Cruise control buttons are generally located near the steering wheel and are mainly divided into lever-type, steering wheel button-type, and steering wheel control group-type.
15
4
Share

What is the maintenance mileage for the BYD Tang?

BYD Tang's first maintenance cycle mileage is 3,500 kilometers, followed by maintenance every 24 months or 7,500 kilometers. Please note that the mileage cycle is calculated based on HEV mileage. The specific details about BYD Tang maintenance are as follows: 1. Regular maintenance items: replacement of engine oil, oil filter, air filter, cabin air filter, and fuel filter. 2. Maintenance cost: engine oil price is 345 yuan, oil filter 29 yuan, air filter 66 yuan, cabin air filter 35 yuan, fuel filter 76 yuan, labor fee 98 yuan, totaling 634 yuan. Note: The first four maintenance services for BYD Tang are free.
4
4
Share

What Does Torque Mean?

Torque is a special type of moment that causes an object to rotate. The details are as follows: 1. The torque of an engine refers to the moment output from the crankshaft end. Under fixed power conditions, it is inversely proportional to the engine speed—the faster the speed, the smaller the torque, and vice versa. 2. Torque reflects the load capacity of a car within a certain range. External torque is called external moment or external couple moment, while internal torque is called internal moment or torque. 3. For engines with the same displacement, higher torque indicates a better engine. Generally, the higher the torque of a car, the better.
20
4
Share

Where is the keyhole located on the Zotye e200?

The keyhole of the Zotye e200 is installed on the driver's side door. You can see the keyhole by prying open the rear cover of the left outer handle with the key. If the one-button start fails, you can use the mechanical key to open the door. Below is an introduction to the Zotye e200: 1. Dimensions: The length, width, and height of the E200 are 2735/1600/1630mm, with a wheelbase of 1810mm. 2. Interior: The vehicle comes standard with power windows, automatic climate control, a 10-inch large touchscreen interactive multimedia system, rear parking radar, mobile phone interconnect system, GPS remote monitoring and maintenance system, anti-theft alarm, etc. 3. Powertrain: The Zotye e200 adopts rear-wheel drive and is equipped with a powertrain consisting of a permanent magnet synchronous motor and a ternary lithium battery, which enables the E200 to achieve a range of 220km and a top speed of 120km/h.
10
2
Share

What is the tire pressure for the Edge?

Ford Edge's normal tire pressure range is 2.4-2.5bar. Due to seasonal factors, winter tire pressure can be appropriately increased by 0.2bar, while summer pressure can be 0.1bar lower. To check tire pressure on the Ford Edge, first enter the vehicle's computer main menu, select Driver Assist, then click to enter Tire Pressure Monitoring to view. The Edge is equipped with a tire pressure monitoring system, and when it detects one or more tires significantly underinflated, a warning light will illuminate. If the low tire pressure warning light comes on, you should stop to check the tires as soon as possible and inflate them to the correct pressure. If the tire pressure monitoring indicator light comes on (a yellow symbol, an irregular circle with no seal on top and four small spikes at the bottom, with an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure. It usually alarms when the pressure is below 1.8bar or above 3.0bar. At this time, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset. After inflating the tires, the tire pressure was not reset in time, causing the tire pressure monitoring system to still record the original data, and the tire pressure monitoring indicator light will illuminate. At this time, simply perform a tire pressure reset. Damaged tire pressure sensor. The tire pressure sensor is used to monitor tire pressure and is directly installed inside the tire, connected to the tire inflation port. If the tire pressure sensor is damaged while driving, it will also cause the tire pressure fault light to come on. For sensor damage issues, only a brand new replacement can be installed.
1
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.