Are Small Lights the Same as Low Beam Headlights?

1 Answers
StZane
07/30/25 9:10am
Small lights refer to low beam headlights. Large lights refer to high beam headlights. Low beam headlights are designed for close-range illumination, with the design requirements focusing on a wide coverage angle (160 degrees), short illumination distance, and non-adjustable focus. High beam headlights emit parallel light, which is more concentrated and brighter, capable of illuminating distant and high objects, thereby improving visibility and expanding the field of view. When to use low beam headlights: When driving in areas without streetlights at night, during dusk when it's getting dark, or at dawn when light is just appearing, it is mandatory to turn on the low beam headlights; if encountering heavy fog, snow, or heavy rain that limits visibility, low beam headlights must be used even during the day; in some areas where lighting is available but insufficient, low beam headlights should also be activated. Function of low beam headlights: Although low beam headlights have an illumination distance of about 30 meters, they feature a very distinct beam cutoff line. Most car low beam headlights illuminate between 30-40 meters, with the beam cutoff line appearing around 12-18 meters. The area in front of the beam cutoff line is brightly lit, allowing clear object identification, and the ground illuminated by low beam headlights typically shows a visible light area of 2-3 meters in diameter.
Was this review help?
5
1
Share
More Forum Discussions

Common Brake Pad Faults?

Common brake pad faults are as follows: 1. Brake pedal not returning: After pressing the brake pedal, the pedal does not return to its original position or returns slowly. This phenomenon is mostly caused by dirt on the wheel cylinder piston. Simply clean the wheel cylinder piston, and ensure that the air in the brake lines and brake fluid is completely bled afterward. 2. Soft brake pedal: A soft brake pedal is very common. Causes include insufficient brake fluid, thinning brake discs and pads, air in the brake lines, or deteriorated brake fluid. The most common issues are deteriorated or insufficient brake fluid. 3. Brake noise: Brake noise mainly occurs when pressing the brake while driving, producing a sharp metal friction sound (very harsh). This may be due to thin brake pads, low-quality brake pads, foreign objects in the brake pads, or rust on the brake discs. Usually, pressing the brake a few more times can alleviate the noise. 4. Brake failure: Brake failure is a very serious issue. Normally, brake failure does not occur unless there are quality issues with the car or faults in the brake system. Brake failure is often related to car quality. When brake failure occurs, first control the direction based on the car's speed, gradually downshift to utilize engine braking, and slowly reduce the speed. When the speed is below 60km/h, consider using the handbrake to slow down (using it at high speeds can cause accidents). 5. Pedal feedback: There are two types of pedal feedback. One is feeling a slight bounce when pressing the brake hard, which is normal. The other is abnormal wear on the brake discs, such as uneven lines. This can cause pedal feedback and reduced braking force. The solution is to replace the brake discs and pads as soon as possible. 6. Hard brake pedal: A hard brake pedal is usually due to a failed vacuum brake booster. The vacuum brake booster has two chambers: one connected to the intake manifold and the other to the external atmosphere. When the engine is running, the intake manifold draws air, creating a fast flow and negative pressure in the negative pressure chamber. The other chamber is connected to the atmosphere. When braking is needed, the pressure difference between the two chambers generates assistance, applying pressure to the brake fluid to create friction between the brake pads and discs, producing braking force. 7. Brake pull: When braking, the steering wheel turns, and the car deviates from its straight path. This fault is caused by uneven braking force on the left and right sides.
19
4
Share

Can the ECO Mode Be Kept On for a Long Time?

It is acceptable to frequently activate the ECO mode in a car. ECO mode, also known as Economy Mode, is particularly effective in saving fuel when driving in congested urban traffic conditions. Under ECO mode, the amount of carbon deposits produced by the engine is roughly the same as in normal operating mode, so the ECO mode can be kept on continuously. The primary principle of ECO mode is not overly complex. It involves a comprehensive analysis and judgment of factors affecting fuel consumption during vehicle movement, such as automatic transmission gear position, engine speed, vehicle speed, braking, and transmission oil temperature. The ECU control unit calculates the optimal amount of fuel to supply the engine for operation, effectively reducing fuel consumption compared to normal driving modes. Simply put, it controls the engine's speed with appropriate gear selection to minimize unnecessary fuel consumption. ECO is an abbreviation, with its Chinese translation representing Ecology (environmental protection), Conservation (energy saving), and Optimization (power). ECO modes are further divided into active ECO driving mode and non-active ECO driving mode. When the ECO indicator light on the dashboard illuminates, it signifies that the vehicle's economy mode is activated. ECO modes are categorized into active and non-active types. The difference lies in the fact that the active type has its own dedicated button, allowing the driver to choose whether to activate it. When the driver presses the ECO mode switch, the dashboard indicator light immediately turns on, and the vehicle automatically begins adjusting settings such as throttle opening, transmission shift logic, and air conditioning output power. Non-active ECO mode does not have a dedicated button; when the dashboard ECO indicator light turns on, it merely serves as a reminder function. ECO automatically evaluates your driving behavior, and if your current driving operation achieves the optimal fuel supply, the dashboard will simultaneously display the ECO indicator light. Most vehicles employ the active ECO driving mode, meaning they have their own switch button. Therefore, during daily driving, we can activate the ECO mode. However, it is unnecessary to enable ECO mode when driving at speeds exceeding 120 km/h, during idle parking, in N/P gear, or in manual mode, especially when climbing hills. Doing so would not only fail to demonstrate the fuel-saving characteristics of ECO but also compromise the vehicle's power performance. Additionally, ECO mode typically becomes ineffective under the following circumstances: When the vehicle speed exceeds 120 kilometers per hour, the system prioritizes speed considerations, causing the ECO mode to deactivate automatically. During idle parking or when in N/P gear or manual mode, ECO may also become ineffective. When high torque output is required, such as during hill climbing, the engine's computer prioritizes ensuring sufficient power to drive the vehicle, and the ECO mode will not function in such scenarios.
16
0
Share

What does the EPC light on a car mean?

The EPC indicator light can illuminate in two states: during the power-on self-test and under other circumstances. The power-on self-test is an indication that the vehicle is checking the status of all sensors before driving. Generally, if the engine is not started after powering on, the light will turn off by itself after about 3 seconds. If the EPC light remains on after the vehicle starts or illuminates under other conditions, the main causes may include faults in the engine intake system, throttle issues, fuel system malfunctions, engine problems, ECU control unit failures, or brake light defects. Below is a detailed explanation of the reasons for the EPC light illuminating under other circumstances: Engine intake system fault: The EPC light will alert when the engine intake is obstructed or insufficient. Throttle fault: Carbon buildup is a common issue with the throttle. Additionally, dirt accumulation can affect intake and trigger the indicator light. Fuel system fault: Examples include substandard fuel, deteriorated fuel, or poor fuel atomization. Engine fault: Insufficient engine pressure or issues with the intake valves and other power system components can also activate the EPC light. ECU control unit fault: This may involve interference with the vehicle computer signals or false alarms from the computer. Brake light fault: Situations such as non-functioning brake lights, faulty brake switches, or brake circuit issues. Solutions for when the EPC light illuminates: Troubleshoot intake system issues, use fuel with the appropriate octane rating, clean the throttle, etc. Remove carbon deposits from relevant components. Re-flash ECU-related data. If the EPC light comes on, the owner can first try turning off the engine and restarting it to see if the light remains on. If it does not, there may be no issue, and the EPC light might have been affected temporarily. If the light stays on or frequently illuminates, the vehicle should be taken to the nearest service center for professional diagnosis and repair to eliminate potential safety hazards. The full English name of EPC is Electronic-Power-Control, which translates to electronic power control. Most people refer to it as the engine electronic stability system. The EPC system primarily includes controllers and sensors related to the power system. When sensor data in the system is abnormal, the EPC system will take predefined actions to address the power system issues. Common EPC indicator lights are typically two colors: yellow and red. A yellow EPC fault light indicates the vehicle can still be driven, but it should proceed slowly to a repair point. A red EPC fault light signifies a more serious issue, and the vehicle should be pulled over immediately, with professional repair services contacted. Continuing to drive under such conditions may directly affect the vehicle's core components or driving safety.
7
5
Share

Can Two-Stroke Oil Be Replaced with Regular Oil?

Two-stroke oil cannot be replaced with regular oil because the added chemical substances are different, posing significant potential harm to the engine. Below is relevant information about two-stroke oil: 1. Introduction: Gasoline engine oil made from refined mineral base oil or synthetic base oil blended with various additives. It is used for spark-ignition, two-stroke engines with water or air as the circulating cooling medium. 2. Grades: Two-stroke gasoline engine oil has two viscosity grades, namely SAE20 and SAE30. Generally, SAE30 is selected. If it is for separate lubrication, use in cold regions, or for ultra-light-duty two-stroke engines, SAE20 is used.
6
1
Share

Where is the keyhole of the Tiida car located?

The mechanical keyhole of the Tiida is located on the main driver's door handle, and there is also a smart-key-sized slot below the start button. Here is some information about the Tiida: 1. The new Tiida has added Dongfeng Nissan's "Smart Travel+" connected car system. 2. The system is equipped with iFlytek voice recognition technology and, in collaboration with AutoNavi Maps, provides real-time online map updates. The system enables intelligent congestion avoidance, inertial navigation, and remote real-time monitoring. Users can remotely monitor the vehicle's status and locate the vehicle in real-time through a mobile app.
16
5
Share

Why should vehicles going straight at an intersection yield to vehicles coming from the right?

Because your vehicle's front is facing the driver's position of the other vehicle, while the incoming vehicle is facing your passenger seat position. From a safety perspective, you are in a relatively safer position than the other party; in case of an accident, your vehicle would hit the driver's side of the other vehicle, so the other party has the right of way to ensure their driver's safety and quick passage. Pedestrian crossing signals indicate: 1. When the green light is on: pedestrians are allowed to cross the pedestrian crossing; 2. When the red light is on: pedestrians are prohibited from entering the pedestrian crossing, but those who have already entered may continue to cross or wait at the center line of the road.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.