Where is the vehicle brake control harness connector located on a Ford F-150 for installing a CURT 51436 Brake Control Adapter Harness?

1Answers

VanLilah

12/17/2025, 11:05:04 AM

To find the vehicle brake control harness connector on your Ford F-150 for your CURT 51436 Brake Control Adapter Harness, follow these steps. First, open the driver's side door and look under the dashboard, positioned above the brake pedal. The connector is typically taped to another harness and should resemble the connector on your CURT brake control harness. Carefully remove any tape or protective covering from the connector, making sure not to damage the locking tabs. Next, plug the CURT brake control harness connector into the vehicle's connector, ensuring it's fully inserted and the locking tabs are engaged. Then, route the brake control harness along the back of the dash, bringing it out the bottom towards the brake control unit. Insert the black connector from the brake control harness into the quick plug connector on the brake control. Secure the harness using the provided cable ties, taking care to avoid any pinch points. Finally, complete the installation by following the specific instructions that came with your brake control unit, including mounting the unit as directed and performing the testing procedures outlined in the brake control's user manual. If you cannot find the harness connector under the dash as described, check the alternative instructions in the installation manual; these often apply to vehicles with a shifter lever in the center console.

Was this review help?

115

More Q&A

How do I connect the Whadda WPSH202 Data Logging Shield to my Arduino board for data logging?

Connecting your Whadda WPSH202 Arduino Compatible Data Logging Shield to your Arduino board involves a few key steps to ensure proper functionality. Here's a breakdown: Board Compatibility: First, confirm that you're using a compatible Arduino board. The Whadda WPSH202 is designed to work with ATmega2560-based MEGA boards and ATmega32u4-based Leonardo boards. Modify Card Info Sketch: You'll need to make some adjustments to the example sketch in the Arduino IDE. Start by opening the 'Card Info' sketch. Then, modify line 36 of the sketch to read: 'const int chipSelect = 10;'. Furthermore, update the line to: 'while (!card.init(SPI_HALF_SPEED, 1, 11, 12, 13)) {'. Update SD Library: Download the updated SD library and the RTClib.zip file. You can usually find these on the product page on the Velleman website. Create a new folder named 'SD' inside your Arduino libraries folder. Extract the contents of the downloaded SD library into this 'SD' folder. Ensure that the .h and .cpp files are placed directly inside the 'SD' folder, not in any subfolders. Physical Connection: Physically connect the data logging shield to your Arduino board by carefully plugging it in. Next, insert a formatted SD card (FAT16 or FAT32) into the SD card slot on the shield. Testing: Open the example sketch 'Card info' in the Arduino IDE. Make sure that line 36 still reads: 'const int chipSelect = 10;'. Follow the instructions provided in the Whadda WPSH202 manual to test the SD card and RTC functionality. Following these steps and consulting the manual for detailed information will help you successfully set up your Whadda WPSH202 data logging shield and start logging data.

103

My WOODFORD Thermaline Heated Yard Hydrant is leaking around the brass stem What should I do

If your WOODFORD Thermaline Heated Yard Hydrant is leaking from around the brass stem, here's how to address the issue: First, try tightening the Packing Nut until it's snug. This is often the simplest fix. If the leak continues, you'll likely need to replace the Packing. For units sold before June 1, 2011, order Packing #80008. For units sold after June 1, 2011, use Packing #30247. If water leaks from the top of the stem when the hydrant is on, inspect the Heater Well. Unplug the hydrant, remove the Heater and Cord assembly, and check if the Heater Well, Heater Well Thumb Nut, or Heater Well Washer are missing or damaged. Replace or reinstall any damaged components. Always consult your WOODFORD Thermaline Heated Yard Hydrant manual or contact WOODFORD MANUFACTURING COMPANY for further assistance.

110

What's the recommended service schedule for AL-KO Enduro X Independent Trailing Suspension?

Keeping your AL-KO Enduro X Independent Trailing Suspension in top shape ensures smooth and safe travels. Based on the AL-KO Enduro X user manual, here’s the recommended servicing schedule: Begin with initial checks and a wheel alignment inspection between 100 to 1,000 km. The first service is due at 5,000 km, followed by a second service at 10,000 km. After that, schedule subsequent services every 10,000 km. Adhering to this schedule is vital for maintaining the performance, longevity, and safety of your AL-KO Enduro X suspension, providing you with confidence on every journey.

102

How to Install the ZALMAN ALPHA24 CPU Liquid Cooler

Installing the ZALMAN ALPHA24 Alpha Series CPU Liquid Cooler on your Intel or AMD CPU involves several steps. Before you begin, take these precautions: avoid touching the operating fan, prevent thermal grease contact with skin or eyes, wear gloves, verify the component list, keep out of reach of children, and only use the cooler as intended. Zalman is not responsible for damage from overclocking or system transport. The ALPHA24 cooler is compatible with Intel sockets LGA2066, 2011-V3, 2011, 1700, 1200, and 115X, as well as AMD sockets AM4 and AM3. To install, first, power off and unplug your system and remove any existing cooler. Next, install the appropriate backplate and screws for your CPU socket type. Then, apply thermal paste to your CPU. Mount the pump onto the CPU and secure it using the provided clips. Connect the pump to the CPU fan header on your motherboard. Install the radiator in your case and mount the fans. Connect the fans to the PWM headers on your motherboard. Finally, connect the LED cable to the addressable RGB header on your motherboard. Power on and configure the RGB lighting via your motherboard software. The pump dimensions are 68mm(L) x 68mm(W) x 62mm(H) with a speed of 3,200RPM±10%. The radiator is pure aluminum and fan dimensions, speeds and noise levels will vary depending on the specific ALPHA24 model. For detailed instructions, consult the user manual included with your ZALMAN ALPHA24 cooler.

111

How do I know when my ANSMANN WL1000R Work Light is fully charged?

Knowing when your ANSMANN WL1000R Rechargeable Work Light is fully charged is simple. The work light has two charge indicators to guide you: Charge Indicator A, which shows the charging status. It will flash red while charging and turn off when the battery is full. Charge Indicator B shows the charge level during charging and use. When both indicators confirm a full charge, it's safe to disconnect the light from the charger. This prevents overcharging and extends the battery's life, ensuring your ANSMANN WL1000R is always ready when you need it.

117

How do I connect my NUM'AXES PIE1058 trail camera to the PIE Cloud app for remote use?

Connecting your NUM'AXES PIE1058 trail camera to the PIE Cloud app enables remote monitoring and control. Here's how to pair them: First, install the PIE Cloud app from the Google Play Store or the App Store. Open the app and create an account using your email and a password. Next, tap the "Pair Camera" button. You can then scan the QR code found on your camera's LCD screen or manually input the camera's ID into the app. Finally, follow the on-screen prompts to finish the pairing. Once connected, you can remotely view photos and videos, manage your media, and adjust camera settings through the PIE Cloud app. For more detailed guidance or troubleshooting, consult the user manual that came with your NUM'AXES PIE1058 trail camera.

115

Where is the vehicle brake control harness connector located on a Ford F-150 for installing a CURT 51436 Brake Control Adapter Harness?

How do I connect the Whadda WPSH202 Data Logging Shield to my Arduino board for data logging?

My WOODFORD Thermaline Heated Yard Hydrant is leaking around the brass stem What should I do

What's the recommended service schedule for AL-KO Enduro X Independent Trailing Suspension?

How to Install the ZALMAN ALPHA24 CPU Liquid Cooler

How do I know when my ANSMANN WL1000R Work Light is fully charged?

How do I connect my NUM'AXES PIE1058 trail camera to the PIE Cloud app for remote use?

Troubleshooting Camera Connection Problems with my Phone

How do I clean and maintain my Elementi ERT18CSCW top freezer refrigerator for optimal performance?

How do I install and use Halco ProLED MR16 Series LED lamps?

What's the best way to clean and maintain the Highmore HM-WB005-001 Rocko Workbench with Pegboard