···
Log in / Register

where do i find the mint mark on a silver dollar

1Answers
LeTheo
12/01/2025, 02:11:13 AM

Hello! That's a great question, as finding the mint mark is key to understanding a coin's history. The location depends on which type of silver dollar you have, but for most of them, you'll be looking on the reverse, or "tails," side of the coin.

For the most common classic silver dollars, like the Morgan Dollar (minted from 1878 to 1921), flip the coin over to the side with the eagle. You will find the small mint mark letter located just below the wreath that the eagle's tail feathers are sitting in, right above the letters "D" and "O" in the word "DOLLAR."

If you have a Peace Silver Dollar (minted from 1921 to 1935), the mint mark is also on the reverse. On this coin, it's located below the word "ONE" and to the left of the eagle’s tail feathers. Even on modern American Silver Eagles, the mint mark is typically found on the reverse side, to the left of the eagle.

These letters tell you which U.S. Mint produced the coin. You might see an "S" for San Francisco, a "D" for Denver, an "O" for New Orleans, or "CC" for the historic Carson City mint. If you can't find a mint mark at all, it usually means your coin was made at the Philadelphia Mint, which often didn't use a mark.

Was this review help?
104
Share
More Q&A

How do I start my scheppach HP2500S Reversible Plate Compactor?

Starting your scheppach HP2500S Reversible Plate Compactor involves a few key steps. First, check the engine oil level by removing the dipstick, cleaning it, reinserting it (without screwing it in), and checking the level. Add the correct oil if necessary and reassemble the dipstick. Next, inspect the fuel level in the tank and add unleaded gasoline if needed, taking care not to overfill. Ensure the fuel valve lever is set to the ON position. For a cold engine, move the choke lever to the CLOSE position; otherwise, leave it OPEN if the engine is warm. Position the throttle lever about one-third of the way towards the FAST setting. Place the shift stick in the neutral position. Turn the engine switch to the ON position. Use the recoil starter, pulling the grip until resistance is felt, then pull briskly and return the grip gently. If the choke was closed, gradually move it to the OPEN position as the engine warms up. Finally, after warm-up, adjust the throttle to increase engine speed and set the shift stick to the desired position to start the plate's vibration and begin compacting. Always ensure the compactor is fully assembled and follow all safety guidelines in the instruction manual before operation.
101
Share

How do I safely install my oneLIGHT 12124x Ceiling Fixed Spot Cylinder?

To ensure a safe and correct installation of your oneLIGHT 12124x Ceiling Fixed Spot Cylinder, please adhere to these guidelines. Prior to beginning, always turn off the power at the main electrical panel to prevent electrical shock. First, securely mount the fixture to the ceiling, ensuring all connections are firm. It is critical to consult the oneLIGHT 12124x's instruction manual for detailed mounting and wiring instructions. Never cover the fixture; maintaining proper ventilation is essential to prevent overheating. All electrical connections must be properly insulated. Regular inspection of the fixture for any damage or wear is recommended. If any issues arise, contact a qualified electrician for repair or replacement. For optimal safety, and if you have any reservations, professional installation by a certified electrician is strongly advised. Remember that professional installation can help ensure the longevity and safety of your oneLIGHT product.
109
Share

Can I reverse the door swing on my KERNAU KFRC 20163 NF B Combi Refrigerator Freezer?

Yes, it's possible to change the door opening direction on your KERNAU KFRC 20163 NF B Combi Refrigerator Freezer, but there are a few important things to consider. First, check if your model has handles installed on the front of the door. If it does, the door swing cannot be changed. If your model is eligible, the best course of action is to contact your nearest Authorised Service Centre. They have the expertise and tools to safely and correctly reverse the door swing. Following their instructions is crucial for ensuring the proper functionality and safety of your refrigerator. They will guide you through the process specific to your KERNAU model.
112
Share

Do Rockville RKL80MW marine speakers need an amplifier

Rockville RKL80MW marine speakers can function without an amplifier, directly connected to a marine stereo. However, to truly unlock their potential, incorporating an amplifier is highly recommended. These speakers boast a 4-Ohm impedance and handle 350 Watts Peak / 85 Watts RMS per speaker. While they'll produce sound when directly connected, an amplifier significantly elevates audio quality, particularly at higher volumes. You'll experience enhanced clarity and a fuller sound profile when using an amplifier with your Rockville RKL80MW speakers.
116
Share

Assembly Guide for the Scheppach HL1020 Log Splitter

Congratulations on your new Scheppach HL1020 Log Splitter! Here's a step-by-step guide to help you assemble it: Wheel Assembly : Begin by sliding the wheel axle through the designated hole at the bottom, rear of the splitter. Attach the wheels to the axle and secure them using the provided splints. Controller Handle Installation : Take the controller arm, which has a slotted hole, and insert it onto the rocker switch. Next, align the drilled hole on the arm with the threaded rod. Use a washer to secure the controller arm and then fasten it with a spring splint pin on the rocker switch and a self-locking nut on the threaded rod. Repeat this process for the other control arm on the opposite side. Holder Arm Attachment : Insert both holder arms into the rectangular steel tubes located on the left side of the splitter. Fasten these arms using two M10 x 45 mm hexagon screws and self-locking nuts for each arm. Trunk Lifter Holder Arm Mounting : Attach the holder arm for the trunk lifter to the frame using two hexagonal screws (M10 x 25). Do not fully tighten these screws at this stage. Trunk Lifter Installation : Secure the trunk lifter between the brackets on the lower, right side of the splitter using a hexagon screw (M10 x 55) and a self-locking nut. Ensure there's a small gap (approximately 0.5 - 1 mm) between the holder arm and the trunk lifter when aligned. Splitting Blade Chain Attachment : Connect the chain to the splitting blade. Preparing for Operation : Connect the splitter to a power source. Lower both controller handles until the cylinder is positioned above the drilled holes at the top. Insert the shafts into these holes and secure them with spring pins. Bring the splitting blade to its highest position and remove the support. For more detailed instructions and safety information, always consult the Scheppach HL1020 Log Splitter Instruction Manual.
105
Share

Can I adjust the tweeter on my Focal F100IWLCR5 speakers for better sound?

Yes, you can adjust the tweeter on the Focal F100IWLCR5 2-Way D'Appolito Loudspeakers. This feature lets you fine-tune the high-frequency response to optimize sound quality. Here's how: On the front of the loudspeaker, you'll find a switch. Use a small tool, like a screwdriver, to move this switch. The switch offers several positions, each corresponding to a different tweeter setting. Experiment with these settings to find the one that best matches your listening preferences and room acoustics. Once you've found the ideal setting, leave the switch in that position. Adjusting the tweeter allows you to customize the treble to your liking, ensuring the best possible audio experience with your Focal speakers.
107
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.