···
Log in / Register

When should I replace the filter and check valve in my SoClean 2?

1Answers
JulianMarie
12/17/2025, 10:21:11 AM

For optimal performance of your SoClean 2 and effective disinfection of your CPAP equipment, it's recommended to replace the cartridge filter and check valve every six months. The device's display will show a reminder message around this timeframe to prompt replacement. Regularly changing these parts helps maintain the SoClean 2's efficiency and ensures your PAP equipment remains properly sanitized. You can easily reorder replacement parts through your authorized SoClean reseller or directly on the SoClean website.

Was this review help?
106
Share
More Q&A

How do I set the dual time on my MIYOTA Cal. JP75 watch?

Setting the dual time on your MIYOTA Cal. JP75 Multi-Function Watch is simple. This feature is particularly useful for travelers or anyone needing to monitor different time zones. To adjust the dual time, consult your watch's manual for specific button designations, but the process generally involves these steps: To set the dual time, use the designated buttons on the watch. Typically: Press button "A" to advance the dual time hand in 15-minute increments. Press button "B" to move the dual time hand backward in 15-minute increments. Holding down either button "A" or "B" will allow for rapid adjustment of the dual time hand. By following these steps, you can easily synchronize your MIYOTA Cal. JP75 watch to the correct dual time.
108
Share

How do I pair my MIBOXER Zigbee 3.0 + 2.4G RGB+CCT Lamp with a remote control?

Pairing your MIBOXER Zigbee 3.0 + 2.4G RGB+CCT Lamp to a remote control is straightforward. Here's how, based on the manual's instructions: To Link the Lamp: Power off the lamp and wait ten seconds. Power the lamp back on. Within three seconds of powering on, quickly press the 'I' button on the remote control three times. The lamp should blink slowly three times, confirming successful linking. To Unlink the Lamp: Power off the lamp and wait ten seconds. Power the lamp back on. Within three seconds of powering on, quickly press the 'I' button on the remote control five times. The lamp will blink quickly ten times, indicating successful unlinking. Additional Features: Dynamic Modes: Use the remote to select various dynamic modes; consult your manual for specifics. Auto-Transmission and Synchronization: The remote control can transmit signals between lights within a 30-meter range and synchronize multiple lights operating in the same dynamic mode.
106
Share

How to Install the Wheel Guard on a Ronix 3161 Angle Grinder?

For safe operation of your Ronix 3161 115mm Mini Angle Grinder, particularly when using grinding wheels, cut-off wheels, or wire brushes, proper wheel guard installation is vital. Always ensure the tool is switched off and unplugged before commencing any procedure. Here's how to install the wheel guard: First, position the wheel guard with its closed side facing you, the operator. Then, align the protrusion found on the wheel guard band with the notch on the bearing box of the grinder. Rotate the wheel guard approximately 180 degrees to secure it in place. Finally, tighten the fixing mechanism securely to ensure a firm attachment. To remove the wheel guard, reverse these steps, carefully loosening and detaching the guard. Refer to the Ronix 3161 instruction manual for detailed instructions and diagrams. Prioritizing correct wheel guard installation significantly enhances your safety while operating your Ronix angle grinder.
118
Share

How can I change the temperature on my SUMMIT FF27BSS refrigerator?

Adjusting the temperature on your SUMMIT FF27BSS Single Zone Refrigerator is straightforward. Here's how: First, use the control panel buttons to raise or lower the temperature. The temperature range you can set is from 36°F to 46°F (2°C to 8°C). Each press of the buttons changes the temperature by one degree. The set temperature will flash on the display for about 5 seconds before showing the current internal temperature. To check the set temperature, simply press either the up or down button once; the display will show the set temperature for 5 seconds. If you want to switch between Celsius and Fahrenheit, press and hold both temperature adjustment buttons at the same time for approximately 3 seconds.
116
Share

Can I reverse the door on my Russell Hobbs RHTTFZ1 table top freezer?

Yes, you can reverse the door on your Russell Hobbs RHTTFZ1 table top freezer. Here's how, based on the typical instructions for this model: First, remove the top plastic hinge cover, setting it aside. Next, unscrew the two screws from the metal bracket and keep them safe. Locate the three plastic inserts on the opposite side of both the freezer and the door. Now, attach the top door bracket to this side using the screws you previously removed, and then replace the plastic hinge cover. After that, remove the adjustable foot from the bottom of the fridge and put it aside. Carefully unscrew the two screws that secure the bottom door hinge, and move the hinge over to the opposite side, securing it in place. Be careful, as the door will be loose during this step. Finally, reposition the adjustable foot to the opposite side of the fridge. Once you've completed these steps, check that the door opens and closes properly. Remember, after reversing the door, allow the appliance to stand upright for at least three hours before you turn it on.
110
Share

How do I set the temperature on my VONROC EH517AC Electric PTC Fan Heater?

Setting the temperature on your VONROC EH517AC Electric PTC Fan Heater is simple. First, the control panel typically displays the current room temperature. To adjust the temperature, use the temperature/timer increase and decrease buttons, often labeled with symbols or letters like A and B on the control panel. You can set your desired temperature anywhere between 16°C and 37°C. After you adjust the settings, the display will flash the target temperature for about 5 seconds, and then it will revert to showing the ambient room temperature. The display will automatically dim after a minute of being inactive. Keep in mind that the VONROC EH517AC heater is designed to automatically turn on and off to maintain the set temperature in the room.
118
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.