···
Log in / Register

is a 1972 silver dollar worth more than a dollar

1Answers
DiQuinn
12/01/2025, 03:44:52 AM

Hello! That's a great question, and it's a common point of confusion for the 1972 Eisenhower dollar. The provided search results unfortunately didn't contain the specific details needed to answer, but I can help with some general information.

The short answer is that it really depends on which version of the 1972 dollar you have.

Most 1972 Eisenhower dollars that were made for circulation are not actually silver. They are composed of a copper-nickel clad and are generally only worth their face value of one dollar, unless they are in exceptionally pristine condition.

However, the U.S. Mint also produced special versions for collectors that do contain 40% silver. These coins were minted in San Francisco and will have an "S" mint mark on them. These silver versions are definitely worth more than a dollar. Their value is tied to the current price of silver as well as their condition, which affects their desirability for collectors.

To tell them apart, you can look at the edge of the coin. If you see a distinct copper-colored stripe, it's the standard clad coin. If the edge is a solid silver color, you likely have the more valuable 40% silver collector's version.

Was this review help?
110
Share
More Q&A

How frequently should I clean the ClearWater II Cartridge Filter?

As a new ClearWater II Cartridge Filter System owner, you'll want to keep your pool water sparkling. You should clean your filter when the pressure gauge reads 5 PSI or more above your starting pressure. Always consult your ClearWater II Cartridge Filter System owner's manual for specific instructions. To clean the filter, follow these steps: First, turn off the pump; cleaning while the pump is running can be dangerous. Next, plug the skimmer and pool return lines, or drain the water level to below the return line. Then, slowly open the air release valve on top of the filter until the pressure gauge reads "0." After that, open the drain cap at the filter's bottom. Once the water drains, press the yellow safety latch and turn the locking nut counterclockwise to remove the lid. Rinse the cartridge element with a garden hose; there's no need to remove it from the filter housing. Finally, reassemble the lid and follow the startup instructions outlined in your original manual. Remember, you should clean the filter when the pressure gauge indicates a reading of ____ PSI above your starting pressure. Maintaining your filter regularly is crucial for optimal pool performance and water clarity.
104
Share

How do I assemble the LEGO 71759 NINJAGO Ninja Dragon Temple set?

Building the LEGO 71759 NINJAGO Ninja Dragon Temple set is a fun experience! Here's how to properly assemble the dragon and temple: First, consult the LEGO 71759 instruction manual. For the Dragon Model: Begin by sorting the pieces needed for the dragon. Follow the step-by-step instructions, ensuring each piece connects securely. Pay close attention to details like the wings, head, and tail. Once assembled, confirm the dragon's limbs and wings move freely. For the Temple Structure: Sort out the temple pieces as indicated in the manual. Follow the detailed instructions carefully, focusing on piece placement for stability. Construct the walls, roof, and additional features as directed. Ensure all temple components are securely connected. Troubleshooting: If you have any difficulties, revisit the manual for clarification. Double-check piece placement to avoid errors. If pieces are missing or assembly concerns arise, contact LEGO customer service for assistance. Enjoy building your LEGO 71759 NINJAGO Ninja Dragon Temple set!
109
Share

How do I set up and use the HORNBACH CFH ISG 147 Inverter Welder for stick welding

Setting up and using the HORNBACH CFH ISG 147 Inverter Welder for stick welding involves several key steps to ensure both safety and successful welds. First, always prioritize safety. Wear essential protective gear, including non-flammable clothing, leather gloves, a welding apron, safety boots, a face mask, and eye protection. Work in a well-ventilated area to avoid inhaling fumes. Never look directly at the electric arc without proper eye protection; use a welding helmet or face shield with protective glasses. Avoid welding in damp or wet conditions and ensure the equipment is properly grounded. Keep the welding area clear of any flammable materials. Next, the installation process requires connecting the earth cable to the negative pole of the inverter and attaching the earth clamp to your workpiece. Connect the welding cable to the positive pole of the inverter. Select your welding current based on the electrode manufacturer's recommendations. Finally, switch on the inverter, and confirm the green LED indicator is illuminated. To begin stick welding, protect your face with your mask or helmet. Initiate the arc by touching the electrode to the workpiece. Maintain the correct welding angle and a consistent speed. Control the arc length to ensure a proper weld pool forms. After welding, use a brush or hammer to remove any slag. For quality welds, select the appropriate electrode type based on the metal's thickness and composition. Ensure your welding current, arc length, and welding speed are correctly calibrated for optimal results. Regular maintenance is also important. Clean the internal components of the welder and check all electrical connections periodically. Replace any worn-out parts promptly to maintain the welder's performance. Should you encounter any welding defects, such as porosity or cracks, consult the HORNBACH CFH ISG 147 Inverter Welder's manual for troubleshooting guidance, which covers common issues like issues starting a spark, no output voltage, incorrect output current, and more. Following these steps will help you use your HORNBACH CFH ISG 147 safely and effectively.
120
Share

How do I install the LEDALITE ID-23 Drywall Trim PoE TruGroove Recessed Micro Linear Light in a drywall ceiling?

To successfully install the LEDALITE ID-23 Drywall Trim PoE TruGroove Recessed Micro Linear Light in your drywall ceiling, adhere to these steps adapted from the product manual. First, prepare the ceiling. Determine the fixture location and type, and install mount brackets, suspension cables, and power feeds based on your layout drawings. Construct a ceiling frame around the fixture cutout to the specified width. Next, focus on the ceiling cut-out details, ensuring it aligns with the specified tolerances. If you're using 2ft standalone fixtures, install end framing members 1” beyond the ceiling cut-out. Then, prepare for installation by installing mounting brackets, suspension cables, and power feeds where required. Mount the 'C' channel perimeter around the ceiling cutout. After that, install the drywall ceiling, cutting the necessary opening according to your layout drawings. Now it's time to install the fixtures. Arrange the boxed fixtures on the floor in their designated mounting locations. Suspend each module by inserting aircraft cables through the grippers on top of the housing. Gradually lift each module to approximately 12 inches below the ceiling. Once power connections are complete, raise all modules to just below the ceiling level. Proceed to join individual modules by sliding the housing modules together, ensuring joiner aligners are engaged inside the trim in the adjacent module. Install joiner brackets on each side of the housing using the provided hardware. Raise the fixture(s) into the ceiling cut-out, beginning at one end for continuous row modules, and gradually raise each module one inch at a time until fully recessed. Trim the excess cable, leaving about 8 inches below the ceiling level, and tuck the excess inside the upper wiring cavity. Finally, install the lens by snapping it into the fixture, referencing the provided layout drawing and ID number. For sensor installation, follow guidelines for sensor spacing and placement to ensure correct operation and proper wiring for individual or whole row control. Following these steps will help you properly install the LEDALITE ID-23 Drywall Trim PoE TruGroove Recessed Micro Linear Light.
115
Share

How do I prepare my MODULARO wc192070 Wooden Shed for assembly and ensure it lasts?

To ensure your MODULARO wc192070 Wooden Shed stands the test of time, proper preparation and maintenance are key. Begin by storing the shed package in a dry, weather-protected location. Choose a shed site away from extreme weather conditions and ensure the shed doesn't directly touch the ground. Avoid storing the package in a heated room before assembly. For warranty purposes, keep all documentation, including the control sheet and purchase invoice, as you may need to submit them to the seller for any claims. The warranty details are outlined in the manual. Once assembled, treat the wooden components with wood preservative immediately. Apply wood impregnation to the floorboards before assembly, and to both the inside and outside of doors and windows. After assembly, apply weather protection paint to shield the wood from moisture and UV radiation. Inspect your shed every six months to catch any issues early. For assembly, gather the following tools: assembly aid, water level, knife, ladder, screwdriver, measuring tape, hammer, saw, pliers, drill, and protective gloves to prevent splinters. Following these steps will help you enjoy your MODULARO wc192070 Wooden Shed for years to come.
105
Share

How do I install the Joie i-Harbour Enhanced car seat safely?

Installing your Joie i-Harbour Enhanced child restraint correctly is crucial for your child's safety. Here's a step-by-step guide: Base Installation: Attach the ISOFIX guides (if needed) to your vehicle's ISOFIX anchor points. Take the load leg from its storage area and extend it. Extend the ISOFIX connectors on the i-Harbour and click them into your car's ISOFIX anchor points. Make sure both connectors click securely and show green indicators. Extend the load leg to the floor of your car until the indicator shows green, confirming correct contact and support. Adjust the load leg's position if necessary to achieve a secure fit. Removing the Base: To detach the base, press the secondary lock buttons and then the ISOFIX releasing buttons before removing it from the vehicle seat. Side Impact Protection: Attach the side impact protection pod on the door-side of the vehicle seat to enhance safety. Head Support and Harness Adjustment: Adjust the head support and shoulder harnesses. The height should be appropriate for your child, considering whether the seat is rearward or forward-facing. Recline Adjustment: Use the recline adjustment button to set the car seat to a suitable position for your child. Rearward Facing Installation: Place the child restraint onto the base and check the indicator to confirm a green light, ensuring it is securely locked. Refer to the manual for instructions on releasing the car seat from the base. Forward Facing Installation: Install the child restraint on the rear vehicle seat. Place your child in the seat. Adjust the harnesses and buckle your child in securely. Always double-check that all indicators show green after installation to confirm a secure and correct fit. Consult the Joie i-Harbour Enhanced instruction manual for detailed visuals and any model-specific instructions.
111
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.