···
Log in / Register

how much is an 1880 us silver dollar worth

1Answers
Gabriel
12/01/2025, 03:14:51 AM

The provided context from the search results does not contain specific monetary values for an 1880 US silver dollar. However, based on general numismatic knowledge, the value of this coin, a Morgan Dollar, depends on several key factors.

The most critical factors determining its worth are its condition, or grade, and its mint mark. An 1880 Morgan dollar will have a mint mark on the reverse side, beneath the eagle's tail wreath, indicating where it was produced. The possibilities are Philadelphia (no mint mark), San Francisco (S), New Orleans (O), or Carson City (CC).

Coins minted in Philadelphia, San Francisco, and New Orleans are quite common. In heavily circulated or worn condition, their value is primarily tied to their silver content, which is about 0.7734 troy ounces. This typically places their base value in the range of $25 to $40, depending on the current price of silver. For uncirculated examples of these common mint marks, the value can increase to between $50 and $100, with exceptionally high-grade specimens fetching more.

The 1880-CC, from the Carson City mint, is considerably rarer and more valuable. Even in a lower, circulated grade, an 1880-CC Morgan dollar is worth a significant premium, often starting over $100. In uncirculated condition, its value can rise to several hundred or even thousands of dollars depending on its specific grade. For an accurate assessment, it is always recommended to have the coin evaluated by a professional coin dealer or a third-party grading service.

Was this review help?
109
Share
More Q&A

How do I manually test the emergency light function of the IOTA ILBDW FBS?

To manually test the IOTA ILBDW FBS Emergency Light's emergency function, follow these steps: First, verify the IPS status indicator light is GREEN. Next, briefly press and release the IPS test button located on the unit. The test will run for 60 seconds. The IPS status indicator light provides feedback during the test. A RED light indicates the battery is charging, and GREEN means it is fully charged. When the light is OFF, the unit is in emergency mode, and FLASHING GREEN means a test is in progress. If the light flashes RED and GREEN, there's an insufficient charge. A FLASHING RED light (once every 0.5 seconds) suggests a missing battery, and a FLASHING RED light (once every 6 seconds) indicates battery failure. Two RED flashes signal a load failure, three flashes mean electronics failure, and four flashes show a temperature out of range. If any issues arise, consult the instruction manual's troubleshooting section. Regular manual testing ensures the IOTA ILBDW FBS Emergency Light's reliability during power outages.
113
Share

How do I determine the ideal hanging height for the HINKLEY 4114 Bette 12 Inch Large Pendant?

To determine the correct hanging height for your HINKLEY 4114 Bette 12 Inch Large Pendant and ensure it complements your space, follow these steps: First, prepare your workspace by finding a clear area. Unpack the fixture and glass components from the packaging, and carefully review the provided instructions before beginning assembly. Safety first: always shut off the electrical current before commencing installation. Now, decide on your desired pendant height. The fixture includes various stem sizes to help you achieve this; consult Drawings 1 and 2 in the manual to identify the necessary stem combinations to reach your desired length. Next, thread the stems together, starting with the longest one, over the wire and onto the pendant's top. Repeat this process until all required stems are connected. Then, slide the collar ring (S) along the wire and over the stems, followed by the canopy (C). After that, feed the wires through the center hole in the swivel attached to the mounting strap (A), and thread the swivel into the top of the final stem. To install the assembled pendant, make all required wiring connections using the provided instruction sheet (IS18). Once the wiring is complete, neatly tuck all wires into the junction box (J). Secure the mounting strap (A) to the junction box (J) using two screws (B) – please note that screws are not included. Ensure the mounting strap is flush against the ceiling. Finally, position the canopy (C) against the ceiling and thread the collar (S) onto the exposed threaded section (L), tightening it to secure the canopy. By following these steps, you'll be able to effectively determine the correct height and install your HINKLEY 4114 Bette 12 Inch Large Pendant.
118
Share

Can I manually set the temperature on my TRUSTECH KPT-1606F PTC Fan Heater?

Yes, you can adjust the temperature on your TRUSTECH KPT-1606F PTC Fan Heater, but only when it is in the 'AUT. Heat' mode. To adjust the temperature, first, ensure your heater is set to 'AUT. Heat' mode by pressing the 'MODE' button until you select this function. Once in 'AUT. Heat' mode, you can increase or decrease the temperature to your preferred level. The heater will work to maintain this temperature. It will then release cool air for 30 seconds after reaching the set temperature to protect the motor and regulate the thermostat. Please note that temperature adjustments are not possible in 'LOW' or 'HIGH' heat modes. For comprehensive information or troubleshooting steps, consult the user manual that came with your TRUSTECH KPT-1606F PTC Fan Heater.
101
Share

How do I best clean the pizza stone for my GBG PIZZOVSS13 Deluxe Wood-Fired Stainless Steel Pizza Oven?

Keeping the pizza stone in your GBG PIZZOVSS13 Deluxe Wood-Fired Stainless Steel Pizza Oven clean is key to delicious pizzas. Here's a safe and effective method: Begin by scraping off any food residue using a stiff, dry brush or a plastic spatula; avoid metal utensils to prevent damage. For persistent stains, mix baking soda with hot water to create a solution. Apply this to the stone and gently scrub with a non-abrasive scouring pad, using minimal water. After scrubbing, wipe the stone with a damp cloth, again, using as little water as possible to prevent absorption. It's crucial to avoid soaps, detergents, oils, or any chemical cleaning agents, as the porous stone can absorb them, affecting future pizza flavor. Always allow the stone to air dry completely before the next use; a dry stone is essential for achieving crispy pizza crusts. Following these steps will help you maintain the quality of your pizza stone and keep your GBG pizza oven producing perfect pizzas.
118
Share

How do I change the maximum CO2 level on my TFA Dostmann Aircontrol Up (model 31.5011.10) CO2 monitor?

To adjust the upper CO2 limit on your TFA 31.5011.10 Dostmann Aircontrol Up Single Beam CO2 Reading Device, follow these simple steps: In normal operating mode, briefly press the CO2 SET button. The display will show the current upper CO2 limit, which is typically set to 2000 ppm by default, or the last adjusted value. To access the setting mode, press and hold the CO2 SET button for approximately two seconds. The displayed value will begin to flash, indicating that you are now in the adjustment mode. Use either the DOWN/CALIBRATE or UP/°C/°F button to increase or decrease the desired upper limit. The adjustment increments are in steps of 10 ppm while the value is flashing. For quicker adjustments, you can press and hold the DOWN/CALIBRATE or UP/°C/°F button while in the setting mode. To confirm and save the new upper CO2 limit, press the CO2 SET button again. If no button is pressed for a period of 20 seconds, the device will automatically exit the setting mode and save the newly set upper CO2 limit. By following these instructions, you can easily customize the upper CO2 limit on your TFA Dostmann Aircontrol Up device to match your specific needs.
118
Share

How do I configure the charging curve on the MEAN WELL DRS-480 All-In-One Intelligent Security Power supply?

Configuring the charging curve for your MEAN WELL DRS-480 All-In-One Intelligent Security Power supply involves several steps to ensure optimal charging for your battery. First, identify your battery type, as the DRS-480 supports lead-acid and lithium-ion batteries. Next, select the appropriate charging curve using the DIP switches; the default is a 3-stage charging process. Consult the manual for specific switch settings corresponding to gel, flooded, AGM, or LiFePO4 batteries, based on your battery's voltage (24V, 36V, or 48V). For more precise control, use the SBP-001 Smart Programmer (sold separately) to fine-tune Constant Current (CC), Tapper Current (TC), Constant Voltage (CV), and Float Voltage (FV). The SBP-001 enables easy configuration through a computer. Also, consider the temperature compensation function; connect the included NTC temperature sensor to the battery to enable automatic voltage adjustments based on temperature. Finally, double-check all settings, including DIP switch positions and temperature compensation configuration, to ensure correct operation and optimized charging for your specific battery.
114
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.