···
Log in / Register

how much is a 1979 silver dollar worth in 2023 no mint

1Answers
Daisy
12/01/2025, 02:13:22 AM

Based on the information provided, it is important to first clarify that the 1979 dollar coin is not made of silver. It is the Susan B. Anthony dollar, which is composed of a copper-nickel clad. This is a common point of confusion, as the term "silver dollar" is often used colloquially for any dollar coin.

A 1979 dollar coin with no mint mark was produced at the Philadelphia Mint. During that year, the Philadelphia Mint did not place a "P" mint mark on the coins it produced, so the absence of a mark is standard for that particular issue.

The value of a 1979 Philadelphia Susan B. Anthony dollar in 2023 depends almost entirely on its condition. If the coin is circulated, meaning it shows signs of wear from being used as currency, it is typically worth only its face value of one dollar.

For a coin in uncirculated or mint state condition, the value increases. These coins can be worth a few dollars more than face value, generally in the range of $2 to $10. There is also a notable variety known as the "Narrow Rim" or "Far Date" 1979 Philadelphia dollar, which is scarcer and can be more valuable, potentially fetching between $5 and $35 depending on its grade. For professionally graded, high-quality examples, the value can be even higher.

Was this review help?
113
Share
More Q&A

How can I reset the Fastcabling 7107-43 Industrial Switch to its default IP?

To reset the Fastcabling 7107-43 8GE 8-Port Managed Industrial Switch to its factory default IP address, follow these steps: First, find the reset button on the switch's front panel. Then, press and hold this button for about 10 seconds. After 10 seconds, let go of the reset button. The switch will now revert to its default IP address of 192.168.2.1/24. Once the switch has been reset, you can access the configuration interface through a web browser using the default IP address. Keep in mind that you might need to adjust your computer's IP address to be within the 192.168.2.* subnet if your current network setup is different. The default login credentials for the web interface are as follows: Username: admin and Password: admin. After logging in with these credentials, you'll be able to configure the switch settings to fit your network's specific requirements.
110
Share

How should I clean the lenses on my Levenhuk Camo 60 spotting scope?

Maintaining the clarity of your Levenhuk Camo 60 spotting scope lenses is essential for optimal viewing. Here's how to properly clean them to ensure peak performance: First and foremost, avoid touching the optical surfaces with your fingers to prevent transferring oils and dirt. Begin by using a blower brush or compressed air to gently remove any loose dust or particles. For smudges or fingerprints, utilize a soft lens cleaning wipe designed specifically for optics. It's crucial to use cleaning materials recommended for optical surfaces to avoid scratching or damaging the lens coatings. Avoid household cleaners and abrasive materials. Regular cleaning, following these steps, will help keep your Levenhuk Camo 60 spotting scope's lenses in excellent condition. If you have any specific concerns, contact a specialized service center for further assistance.
108
Share

How do I switch modes on my Xmart HL-POLE-03 Solar Lamp?

Changing the operating mode on your Xmart HL-POLE-03 Solar Lamp is straightforward. Here's how to do it: First, to turn the lamp on or off, press the switch for about 1.5 seconds. Next, to cycle through the different modes, press the switch briefly. The Xmart HL-POLE-03 offers three distinct modes: Mode 1 (Red) provides 120LM for 5 hours, followed by 3000LM activated by PIR for 10 seconds. Mode 2 (Orange) delivers 240LM for 5 hours, with 3000LM triggered by PIR for 10 seconds. Finally, Mode 3 (Green) offers 400LM for 5 hours, plus 80LM with PIR activation at 3000LM until dawn. To select your desired mode, repeatedly press the switch until you reach the option that fits your needs. The indicator light also provides battery status: Green signifies a battery level above 80%, Orange indicates between 50% and 80%, and Red shows a battery level below 50%. The indicator LED constantly displays the battery capacity. When you change modes, the selected mode will be displayed for 30 seconds before the battery capacity indication resumes. This ensures you can easily customize the Xmart HL-POLE-03 Solar Lamp to match your specific lighting preferences.
110
Share

How do I change the temperature on my MEGAWISE KL-1025 Hair Straightener Brush?

Adjusting the temperature on your MEGAWISE KL-1025 Hair Straightener Brush is simple. First, plug in the brush and press the power button for half a second to turn it on. The display will initially show "OFF". The default temperature setting is 355°F/180°C. You can adjust the temperature by pressing either the "+" or "-" button. The digital display will flash while the brush is heating up to your selected temperature and stop flashing once it reaches the set temperature. For optimal results and to prevent hair damage, consider these temperature recommendations based on hair type: For thick or dense hair, use a temperature range of 410 ~ 450°F / 210 ~ 230°C. Medium volume hair works best with temperatures between 340 ~ 390°F / 170 ~ 200°C. If you have soft or fine hair, set the brush to 265 ~ 320°F / 130 ~ 160°C. To use the brush, section your hair and slowly comb it through, ensuring the hair reaches the inner heating area of the brush. For slight flips at the ends, rotate your wrist as desired. For a voluminous blowout, brush your hair from underneath, curling inward at the ends. To switch between Celsius and Fahrenheit, simultaneously press and hold the "+" and "-" buttons. To turn off the brush, press and hold the power button for two seconds. For detailed instructions and safety information, please consult the user manual that came with your MEGAWISE KL-1025 Hair Straightener Brush.
102
Share

How do I use the timer function on my Premium Levella PFT423R 42-inch tower fan?

Setting the timer on your Premium Levella PFT423R 42-inch tower fan is straightforward. Here's how: First, grab your remote control. You'll find a button labeled "Timer" or "Set Timer." Press this button to enable the timer function. Next, use the up and down arrow buttons on the remote to choose your desired timer setting. Common options include 1, 2, 4, or 8 hour increments. Finally, press the "Timer" button once more to confirm and activate your selection. Your Premium Levella fan will now run for the duration you've set and automatically turn off when the timer expires. For more specific instructions, always consult the user manual that came with your fan. If you need further assistance, the manual also offers troubleshooting tips and contact information for the manufacturer's customer support.
116
Share

How do I charge my Denver SWC-362 smartwatch?

To charge your Denver SWC-362 smartwatch, follow these simple steps for optimal performance: First, always use the charger that came with your watch. Next, carefully align the metal charging contacts on the back of your watch dial with the corresponding metal charging port on the charging base. Then, securely place the watch dial onto the charging tray. Finally, plug the USB connector into a power source, like your computer or a wall charger. Remember, it's best to turn off your device before cleaning it. Only use the original charger to avoid any potential damage to your Denver SWC-362 smartwatch.
106
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.