···
Log in / Register

how much is a 1941 us nickel worth

1Answers
VanAvery
12/01/2025, 04:33:10 AM

Hello there! The information provided in the search results didn't contain specific details about the nickel's value, but I can certainly help you with that based on general coin knowledge.

The value of a 1941 US Jefferson nickel really depends on a couple of key factors: its condition and its mint mark.

First, you'll want to check for a mint mark on the reverse (back) of the coin, to the right of the Monticello building. If there's no mint mark, it was made in Philadelphia. If you see a small "D," it's from the Denver mint, and an "S" means it was minted in San Francisco.

For a common, circulated 1941 nickel that you might find in old pocket change, the value is typically not very high. Most coins from any of the three mints in well-worn condition are worth around 10 to 50 cents.

However, if the coin is in uncirculated or "mint state" condition, meaning it has very little to no wear and still has its original luster, the value increases significantly. An uncirculated 1941 nickel from the Philadelphia mint might be worth a few dollars. The Denver ("D") and San Francisco ("S") versions are a bit less common and can be worth a bit more in the same pristine condition, often starting around $5 and going up from there for exceptionally well-preserved examples.

To get the most accurate value, especially if your coin looks brand new, it's always a good idea to have it looked at by a reputable coin dealer.

Was this review help?
118
Share
More Q&A

My Raging LED Bull isn't lighting up with sound or breath, what should I check?

If your Raging LED Bull's LEDs aren't activating when sound is detected or when you blow into its nose, here's a troubleshooting guide: First, inspect all solder joints for any cold solder joints or loose connections. Next, carefully verify that all components are in their correct locations and orientations as specified in the Raging LED Bull DIY Kit instructions. Pay close attention to the polarity of components marked with "!", such as diodes and capacitors, ensuring they align with the schematic. Confirm your 9VDC battery power supply is functioning correctly and properly connected to the circuit; check the voltage. Experiment with adjusting the potentiometer to see if it affects the LED behavior; this controls the bull's anger sensitivity to sound. Check the microphone (sound sensor) for proper positioning and unobstructed operation. Finally, visually inspect all components for damage. Addressing these points systematically will help you resolve the LED issue. If problems persist, consult the troubleshooting section in the kit's manual or contact the manufacturer for further support.
109
Share

What sandpaper should I use with my RYOBI RPS80 80W Palm Sander?

Choosing the right sandpaper grit is key to getting the best results with your RYOBI RPS80 80W Palm Sander. Here's a quick guide: Coarse Sanding (80-grit): Perfect for aggressive material removal and tackling rough surfaces. Use this for your initial sanding passes. Medium Sanding (120-grit): Ideal for smoothing surfaces, removing minor imperfections, and preparing for finishing. Fine Sanding (150-grit): Use this for achieving a super-smooth finish and prepping for paint or stain. Always work your way up the grit scale, starting with a coarser grit and progressing to finer grits. Sand with each grit until the surface is uniform and smooth before moving to the next. This ensures you achieve the best possible finish with your RYOBI RPS80.
105
Share

How should I transport and position the SUPERVAC F200Ti Industrial Blower/Exhauster?

To safely and effectively use the SUPERVAC F200Ti Industrial Blower/Exhauster, proper transport and positioning are essential. This unit features four carry handles, thoughtfully placed on each corner for convenient handling and quick setup. For transport, leverage these handles to lift and move the blower, with one or two people depending on the situation. The design incorporates heavy-duty rubber feet, ensuring the blower remains stable during operation. When positioning the SUPERVAC F200Ti, select a stable and level surface to prevent movement. Also, check that the front and rear guards are unobstructed. These guards are crucial for preventing accidental contact with vital components. Adhering to these steps will help you transport and position the SUPERVAC F200Ti Industrial Blower/Exhauster for peak performance and safety.
110
Share

Is my device compatible with the ANSMANN 254PD Home Charger?

Determining if your device is compatible with the ANSMANN 254PD Home Charger is straightforward. First, confirm that your device supports the Power Delivery (PD) protocol. The charger provides several output voltages: 5.0V, 9.0V, 12.0V, 15.0V, and 20.0V. Ensure your device is rated for one of these voltages. The ANSMANN 254PD Home Charger automatically detects the power requirements of your connected device, meaning no manual settings are needed. However, to ensure optimal charging, use a PD-compatible cable and make sure your end-device is also PD-compatible. Note that devices requiring more than 45.0W of power from their original chargers might charge at a slower rate. Compatibility can vary due to different PD end-devices and software/firmware versions. If you have any compatibility concerns, refer to your device's specifications or contact ANSMANN customer support for assistance.
114
Share

How do I check the battery charge on my Westfalia 900250 ALK 18 air compressor?

To check the battery level of your Westfalia 900250 ALK 18V Li-Ion Air Compressor, simply press the button located on the battery pack itself. The built-in charge indicator will illuminate to display the current charge status. A lit right LED signifies a high charge level, meaning your compressor is ready to go. Conversely, a lit left LED indicates a low charge, signaling that it's time to recharge the battery. To avoid unexpected shutdowns during use, it's always a good idea to ensure the battery has sufficient power before starting any task. This also helps to prevent potential safety issues.
105
Share

How do I effectively adjust the panels on my FEIT Electric ADJ8000 garage light?

Adjusting the panels on your FEIT Electric ADJ8000 8000 Lumen Foldable Panel Garage Light is straightforward. Begin by locating the four adjustable panels on the fixture. Gently take hold of each panel and move it to your preferred angle or position, according to your lighting requirements. You can position the panels in several modes: Storage Mode, Half Open Mode, or Wide Angle Mode. Choose the mode that best illuminates the desired area. Once you've adjusted the panels, make sure they are securely in place to prevent any shifting during use. Experiment with different panel configurations to discover the perfect lighting setup for your garage or workspace. For visual assistance and more detailed information about adjusting the panels and the various modes, please consult the instruction manual that came with your FEIT Electric ADJ8000.
103
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.