···
Log in / Register

How do I install the tip-over restraint for my Ashley Five Drawer Chest?

1Answers
DeMartin
12/17/2025, 04:10:27 PM

To ensure the safety of your family, here's how to install the tip-over restraint for your Ashley 10506460 Five Drawer Chest: First, find a wall stud where you want to place the chest. Next, secure one bracket (A9) to the wall using the long screws (A7). Then, attach the second bracket (A9) to the underside of the top of the chest using the small screws (A8). After that, thread the zip tie (A10) through the open holes of each bracket and slide it into its end. Finally, pull the zip tie tight to firmly secure the chest to the wall. This tip-over restraint is crucial for preventing furniture tip-over incidents, particularly if you have children.

Was this review help?
114
Share
More Q&A

What is the recommended charging time for the MONI WN-1166 ride-on car's battery?

For optimal performance, charge the battery of your MONI WN-1166 Children's Toys Ride on Car for 8 to 10 hours. Avoid exceeding 10 hours of charging to prevent overcharging. To maintain the battery's health, charge it after each use. If the ride-on car isn't used frequently, recharge it at least once a month. Before charging, always ensure the power button is switched off.
111
Share

How do I manually test my ILB CP20 HE AELR HV emergency light?

To manually test your ILB CP20 HE AELR HV emergency light, follow these straightforward steps. First, make sure the unit has a full charge before you begin. Next, locate and briefly press the Three-Color Test Switch (TCTS) on the emergency light. Keep in mind that manual testing requires a full 24-hour charge to function correctly. The manual test won't disrupt the automatic testing schedule of your ILB CP20 HE AELR HV. During the manual test, the TCTS will show the same diagnostic information as the automated tests. If your unit is connected to the emergency lighting system software, the manual test results will be available for review in the application. By following these steps, you can easily verify that your ILB CP20 HE AELR HV emergency light is working correctly.
106
Share

How to correctly adjust the xxxx length when installing the fixture canopy?

To properly adjust the xxxx length for secure fixture canopy mounting, adhere to these steps: First, raise the fixture and insert screws (AA) through the two canopy mounting holes. While supporting the fixture, thread screws (AA) into or out of the round mounting plate (CC) until 3/16" of the screw threads are visible. This adjustment provides the correct length for secure mounting, as per the subsequent instructions. Then, lower the fixture and tighten the hex nuts (DD) against the round mounting plate (CC). This secures the adjusted thread length, ensuring proper fixture installation. Following these steps ensures your xxxx length is correctly set for a safe and secure canopy mount.
119
Share

How can I replace the batteries in my Multimic 102+ AC Current Mini Digital Clamp-On Tester?

Replacing the batteries in your Multimic 102+ AC Current Mini Digital Clamp-On Tester is straightforward. Here’s how: When the battery indicator displays a "B" mark, signaling low power, turn the device off. Locate the battery cover on the back of the unit. Remove the cover. Insert two LR-44 or SR-44 batteries, carefully aligning them with the correct polarity markings inside the battery compartment. Always replace both batteries simultaneously to prevent inaccurate readings due to voltage discrepancies. Following these steps will ensure your Multimic 102+ continues to operate accurately.
101
Share

Need help assembling the aivituvin AIR 26 Rabbit Hutch? Assembly guide

Assembling your aivituvin AIR 26 Rabbit Hutch is straightforward. Here's a step-by-step guide to help you: First, attach the front (Part K) and roof panels (Part L) to the side panels (Part J) using 10 screws (P2) to create the small house. Repeat for the second house. Next, secure the ramp (Part I) to the layer (Part G) with 2 screws (P4). Then, assemble the two seesaws, using 2 screws (P2) each. After that, attach the side panels (Part C & D) to the front panel (Part A) using 4 screws (P1), aligning them with the dowels. Now, attach the back panels (Part B) to the side panels, again using 4 screws (P1) and aligning with the dowels. Slide in the tray (Part E), and then place the lower layer into the slot of the back and side panels, followed by the upper layer. Position the small houses on the layers and insert the seesaws into the cage. Add the chewing toy (P6) and bowls (Part O & P). Finally, attach the roof (Part F) to the back panel using 6 screws (P3). Fix the hook eye to the left side panel and tie the rope to the eye hook. Always refer to the aivituvin AIR 26 instruction manual for detailed visuals. For any assembly issues or questions, contact aivituvin customer service at service@aivituvin.com .
103
Share

How do I ensure smooth upper blade guide movement on my CRAFTSMAN CMXEBAR600 band saw

To ensure smooth upper blade guide travel on your CRAFTSMAN CMXEBAR600 corded bench band saw, follow these steps: First, loosen the upper guide lock by turning it counterclockwise. Next, use a Phillips screwdriver to adjust the two screws located near the upper guide lock. These screws fine-tune the blade guide's movement. After adjustment, check the movement of the blade guide assembly by moving it up and down; it should move freely and hold its position. If needed, make further adjustments to the screws until the blade guide operates smoothly and holds securely. Finally, tighten the upper blade guide lock by turning it clockwise. Properly adjusting the blade guide will improve the band saw's performance and safety.
108
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.