···
Log in / Register

does total wine take returns

1Answers
SanGeorge
12/01/2025, 04:11:50 AM

So, did your eyes prove bigger than your wine rack? Or did the party end with a few too many unopened bottles of bubbly? Fear not, because Total Wine is generally quite understanding about your enthusiastic over-purchasing.

The short and sweet answer is yes, Total Wine will gladly take back your unopened, resalable spirits, as long as you have your original receipt. As one savvy wedding planner on Reddit confirmed, you can indeed return your untouched wine, beer, and liquor, which is a fantastic policy for anyone who played it safe when stocking the bar for a big event.

However, like a complex Cabernet, there are a few notes to consider. This generous return policy has a bit of a wrinkle depending on where you live. If you're in Arizona, California, Georgia, Hawaii, Indiana, Kentucky, Michigan, North Carolina, South Carolina, Texas, or Washington, the rules are much stricter. In those states, they will only accept returns for products that are defective. So, if you just changed your mind about that Malbec, you might be out of luck. And if you've lost your receipt, you may have to settle for store credit at the manager's discretion.

Was this review help?
108
Share
More Q&A

How do I replace the screwdriver bits on my Sealey CP36MS Cordless Lithium-Ion Screwdriver?

Changing screwdriver bits on your Sealey CP36MS Cordless Lithium-Ion Screwdriver is straightforward. Here's a step-by-step guide: Bit Selection from Fitted Magazine: a. Pull the magazine carrier forward and rotate the magazine until your desired bit is at the top. You can see which bit is selected through the magazine viewer. b. Once the correct bit is positioned, push the magazine carrier back toward the handle to load the bit into the screwdriver. Changing the Magazine: a. Pull the magazine carrier forward. b. Push the magazine to the left until it hangs below the screwdriver. c. Pull the magazine forward to detach it from the spindle. d. Place the new magazine onto the spindle and swing it back into the magazine carrier. e. Finally, push the magazine carrier back into its original position. By following these simple steps, you can quickly and easily swap bits on your Sealey CP36MS, making it ready for any task. Always handle the bits and magazines with care to prevent damage.
108
Share

How do I install the TREND TP30018AB Brass Mini Drop Light?

Installing the TREND TP30018AB Brass Mini Drop Light involves several key steps. Safety is paramount, so always begin by turning off the power at the circuit breaker. First, gather your tools and verify you have all the components, cross-referencing with the instruction manual. Next, attach the mounting bar to the outlet box using the provided screws. Then, connect the wires: use wire connectors to join the white and black wires, and secure the ground wires to the mounting bar. Finally, attach the canopy to the outlet box and secure it with the ball nut. Remember these crucial safety precautions: if you're uncertain about any electrical wiring, consult a qualified electrician. Ensure all connections adhere to local and National Electrical Code (N.E.C.) standards. Proper wiring practices are essential to prevent fire hazards. Following these steps and prioritizing safety will help you successfully install your TREND TP30018AB Brass Mini Drop Light.
103
Share

How do I program the timer on my FKK 24 Electric Fireplace?

Scheduling your FKK 24 Electric Fireplace to automatically turn on and off is easy. Here's how to set the timer: Begin by pressing and holding the "M" button on the remote control to enter the timer setting mode. Use the +/- buttons to set the hour for the start-up time for the first program (M1) on the desired day of the week. Confirm your hour selection by pressing the clock button, then set the minutes using the +/- buttons. Press the clock button again to set the turn-off time for the first program on that same day. Repeat this process to set the start-up and turn-off times for the second program (M2) on the same day. Continue setting start-up and turn-off times for each day of the week by pressing the clock button to cycle through the days. The appliance will exit the timer setting menu and save your settings if no button is pressed for 10 seconds. If you set 00 for either the start-up or turn-off time of a cycle, that cycle will be skipped. You can activate the timer function at any time during normal operation by pressing the "M" button on the remote control. The active timer is indicated by a clock symbol on the display. Following these steps, you can customize your FKK 24 Electric Fireplace to operate on your schedule.
114
Share

How do I connect my Eltako RS485 Bus Actuator 2-Channel Impulse Switch to the Eltako-RS485 bus?

Connecting your Eltako RS485 Bus Actuator 2-Channel Impulse Switch to the Eltako-RS485 bus involves a few key steps. First, it's crucial to have a qualified electrician handle the installation to ensure safety and prevent electrical hazards. Once installation is deemed safe, locate the RS485 bus connection points on the actuator. Bus cross wiring and the power supply are connected using a jumper. For each channel, connect the neutral (N) conductor to the respective terminal (N1 for one channel, N2 for the other), and the live (L) conductor to the corresponding terminal (L for channel 1 and L for channel 3). This setup is designed for zero passage switching of the 230V AC voltage, which minimizes wear on the contacts. The Eltako actuator is energy-efficient, with a standby consumption of approximately 0.1 watt. It's also designed to retain its switching state during power failures and to switch off in a defined mode upon power restoration. Remember that the channels can be taught-in separately as ES and/or ER channels. Always refer to the Eltako RS485 Bus Actuator 2-Channel Impulse Switch manual for specific details and diagrams to ensure a correct and safe connection.
108
Share

Need help installing the ZEVNI A04628 Gaza 4-Light Black Transitional Chandelier? How do I install it?

Installing the ZEVNI A04628 Gaza Chandelier involves several steps. Before starting, ensure you have all necessary tools and understand basic electrical safety. Here's a step-by-step guide: Pre-Installation Assembly: Thread the fixture wires through the stem (M), upper frame (K), and loop (J). Secure the upper frame (K) by connecting the loop (J) and stem (M) to the top of the sockets assembly (Q). Insert the threaded tubes (O) into the upper frame (K) and secure them with nuts (L). Insert the threaded tubes (O) into the lower frame (R) and secure them with nuts (L). Adjusting Hanging Height: Determine the ideal hanging height. Use chain pliers to remove excess chain links. Attach the quick link (H) to the chain (I) and connect it to the loop (J) on the top of the upper frame (K). Carefully weave the fixture wires through the chain (I), alternating in and out of each link, all the way up to the top. Ensure the wires are not strained. Mounting to the Ceiling: Remove the collar ring (F) from the collar loop (G). Attach the single bar (C) to your outlet box using the provided mounting screws (B). Hold the canopy (E) over the collar loop (G) to check its position and then secure it using the collar ring (F). Pass the chain (I) through the collar ring (F) and then through the canopy (E). Attach the quick link (H) to the collar loop (G), and feed the fixture wires through the collar loop (G) up to the pre-assembled threaded section. Making Electrical Connections: Connect the ground wires, neutral wires, and live wires according to the wiring diagram. The ZEVNI A04628 should include a clear wiring chart. Twist the wires together using plastic wire connectors, making sure they are tightly joined. Wrap each connector with approved electrical tape for extra safety. Carefully tuck all wires into the outlet box. Finishing Touches: Raise the canopy (E) to the ceiling and fasten it by tightening the collar ring (F) onto the collar loop (G). Install the correct type of light bulbs (not included), making sure they match the recommended wattage specified on the socket. Attach the glass shades (N) to the sockets (P). Testing and Enjoying: Before turning on the light, double-check all connections to ensure everything is properly installed and secure. Turn on the light and enjoy your new ZEVNI A04628 Gaza 4-Light Black Transitional Chandelier! Always prioritize safety. If you are uncertain about any part of the installation process, it's recommended to consult a qualified electrician.
116
Share

How frequently should I test my SEBSON GS506G smoke alarm, and what's the testing procedure?

To ensure your safety, the SEBSON GS506G smoke alarm should be tested weekly. Here's how to perform the test: First, make sure the battery is correctly inserted. Then, press and hold the TEST button located on the SEBSON GS506G for about 5 seconds. You should hear the alarm sound, and the LED light will illuminate red. This confirms that the electronics, the alarm unit, and the battery are all working properly. Release the TEST button; the alarm should stop immediately. If the alarm doesn't sound or the LED doesn't flash during the test, this could mean the battery is dead, or there might be an issue with the device. In this situation, replace the battery or consider replacing the SEBSON GS506G smoke alarm. Always avoid holding the alarm close to your ear during the test to prevent any potential hearing discomfort. Also, never use an open flame to test the smoke detector, as this could damage its sensor.
112
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.