···
Log in / Register

are bicentennial half dollar coins worth anything

1Answers
VanBarrett
12/01/2025, 01:38:06 AM

That's a great question! A lot of people have these special Bicentennial half dollars with the "1776-1976" date and wonder the same thing. The short answer is: yes, they can be worth more than 50 cents, but most of them aren't. It really comes down to the specific type of coin you have.

The vast majority of Bicentennial half dollars you'd find in pocket change are made of a copper-nickel alloy. Over 500 million of these were minted, so they are very common and, in circulated condition, are typically only worth their face value of 50 cents. If you have one that's in pristine, uncirculated condition, it might be worth a couple of dollars to a collector.

The real value comes from the special collector versions that were made with silver. The U.S. Mint issued sets for collectors that contained Bicentennial half dollars made of 40% silver. Because of their silver content, these coins will always be worth more than face value, with their base value tied to the current price of silver. These special silver coins were sold in both uncirculated and "proof" versions, the latter having a beautiful, mirror-like finish.

So, to figure out if your coin is valuable, the key is to determine if it's a common copper-nickel coin or one of the less common 40% silver versions. The coin's condition also plays a huge role; a perfectly preserved coin is always worth more than a worn one.

The information from the provided coin-identifier source helps clarify what makes these specific Kennedy half dollars valuable, pointing to these different versions. The other YouTube source provided was not relevant to the topic.

Was this review help?
105
Share
More Q&A

How do I install the HOBO RX3000 Channel Kit for my remote monitoring station?

To properly install the HOBO RX3000 Channel Kit for your remote monitoring station, follow these steps to ensure a secure and weatherproof setup: Sensor and Cable Installation : Begin by installing all sensors and cables within the station according to the HOBO RX3000 Remote Monitoring Station Manual. Ensure all connections are secure. Water Level Sensor Cable Channel (if applicable) : If you are using a water level sensor module, replace the smaller cable channel, which came pre-installed, with the one included with the water level sensor module. Grease the Rubber Cable Channel : Apply a thin layer of silicone grease to the outer edges and the inside of the rubber cable channel. Also, lightly grease the portion of each cable that will be placed inside the channel. This grease helps with weatherproofing and cable sealing. Position Cables in Channel : Carefully place the cables into the grooves provided in the rubber cable channel. Make sure the cables are routed correctly and are not excessively strained. Insert Cable Channel into Station : Insert the cable channel into the cable access opening until it's flush with the outside of the station's case. Gently pull the cables towards you as you insert the channel to minimize excess cable within the station. Secure the Plate : Use the provided thumbscrews to secure the plate over the cable access opening. Do not fully tighten the thumbscrews at this stage. Plug the Holes : Fill all unused holes in the cable channel with the rubber plugs provided. Lightly grease each plug before insertion for enhanced sealing. Repeat for the Second Channel : Repeat steps 2 through 7 for the second rubber cable channel, if your setup requires it. Final Tightening : Once all cables and plugs are in place, use the included wrench to tighten the thumbscrews on each plate until they are flat against the case. This completes the installation. By following these steps, you can ensure a reliable and weather-resistant installation of your HOBO RX3000 Channel Kit. For detailed diagrams or additional troubleshooting, consult the HOBO RX3000 Remote Monitoring Station Manual or contact Onset Computer Corporation's support team.
105
Share

How can I calibrate my Somogyi FPL 80W soldering iron for accurate temperature readings?

To calibrate your Somogyi FPL 80W electric soldering iron, follow these steps: First, allow the soldering iron to heat up for 90 seconds after turning it on. Then, using a temperature measuring device, touch the soldering tip. Applying a small amount of solder can help improve heat transfer. Once the temperature reading stabilizes on your measuring device, record the value. Next, remove the thermometer and simultaneously press the '+' and '-' buttons to enter calibration mode. Now, adjust the calibration based on the temperature difference: If the measured temperature is higher than the set temperature, use the '-' button to decrease the temperature value by the difference. Conversely, if the measured temperature is lower, use the '+' button to increase the temperature accordingly. Finally, press the '+' and '-' buttons together again to finalize the calibration. For example, if your soldering iron is set to 320°C, but your thermometer reads 330°C, adjust the calibration to '-10' to correct the reading. Important calibration tips to remember: the maximum compensation range is +/- 99°C. It's best to perform calibration at 320°C for optimal accuracy. After calibrating, the difference should be within ±4°C. For consistent accuracy, recalibrate your Somogyi FPL 80W soldering iron annually. If you experience persistent temperature discrepancies, consult a professional technician.
113
Share

What's the best way to charge my solar light for peak performance?

For optimal performance, charge your solar light in direct sunlight for two full days before its first use. This initial charge is crucial for maximizing battery life and ensuring your solar light functions at its best. Always remember to set the power switch to the "ON" position during charging. This allows the solar panels to effectively capture sunlight and store energy. Following these steps will ensure you get the most out of your solar light.
108
Share

How should I correctly position Dinan strut braces during installation for my vehicle?

To properly install your Dinan strut braces, refer to the Dinan D180-0016 G29 Z4 Strut Brace Instruction Manual. When positioning the left and right braces, make sure the 'DINAN' logo on each brace is oriented to read from left to right when viewed from the corresponding side of your vehicle. This orientation is crucial for optimal performance and ensures the braces are aesthetically aligned. Double-check the alignment before tightening the screws to secure the braces.
117
Share

What is the ideal charging duration for solar panels to achieve peak performance?

To get the most out of your solar-powered lights, it's essential to allow sufficient charging time. As per the instructions, charge the battery for a minimum of 8 hours before using it for the first time. This initial charge is critical for the battery to build up to its full capacity, which ensures the lights operate at their best. Furthermore, position the solar panel where it can get the most sunlight. This maximizes the panel's ability to effectively charge the battery throughout the day.
111
Share

How do I copy the EDID from a display using the StarTech VSEDIDDVI EDID Ghosting Emulator?

To copy the EDID from your display device using the StarTech VSEDIDDVI DVI DDC EDID Ghosting Emulator, follow these simple steps: First, set the rotary dial on the emulator to position 1. Next, connect the USB to DC power cable from the emulator to a USB port on either your video source device (ensure it's powered on) or your display device. The Status LED will illuminate blue, indicating power. Then, connect the EDID-compliant display device to the Monitor port on the emulator using the correct DVI cable (DVI-D, dual or single link). Make sure the display device is powered on. Now, press and hold the EDID PROGRAM button on the emulator until the Status LED begins to flash green. The LED will flash green and red while the EDID is being copied. Finally, once the Status LED returns to solid blue, the EDID copy is complete. You have successfully cloned the EDID using the StarTech VSEDIDDVI DVI DDC EDID Ghosting Emulator.
119
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.