Will there be any impact if a car that requires 92 octane fuel is filled with 95 octane?

2 Answers
QuinnFitz
07/29/25 12:44am
A car that requires 92 octane fuel can be filled with 95 octane gasoline. 95 octane gasoline has higher purity than 92 octane, releasing more kinetic energy when burned in the engine. Therefore, in terms of the power provided by the fuel, higher fuel-saving performance will be highlighted. Reference for gasoline grade selection: The biggest difference between different grades of gasoline lies in their anti-knock performance, which is an important indicator for measuring fuel quality. Cars with an engine compression ratio between 8.6-9.9 should choose 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should choose 95 octane gasoline. If the compression ratio is even higher, 98 octane gasoline should be selected. Generally, the higher the gasoline grade, the higher the octane number and the better the anti-knock performance. Long-term effects of using the wrong gasoline grade: Using a higher octane fuel in a car designed for lower octane will not cause damage, but the increase in octane number will change the ignition point of the fuel, leading to delayed combustion in the engine. This means both the engine's power output and thermal efficiency will decrease. Conversely, using lower octane fuel in a car designed for higher octane can cause engine knocking, increased resistance during the upward stroke, and abnormal wear on the piston and cylinder. In severe cases, it can even lead to cylinder scoring.
Was this review help?
3
3
Share
GemmaDella
08/12/25 4:56am
I drove a car that usually takes 92-octane gasoline, and once the gas station didn't have 92, so I only filled up with 95-octane. After driving, I didn't feel any difference at all—the engine ran smoothly, and the power and fuel consumption were exactly the same as before, except I spent a few dozen yuan more. I talked to a friend about it, and he said the main difference between 92 and 95 is the anti-knock performance, with 95 having slightly better knock resistance, which is beneficial and harmless to the car. However, it's best to follow the manual's recommendations, and upgrading isn't necessary. Remember, occasionally using 95-octane won't harm your car—just your wallet will be a bit lighter.
Was this review help?
5
1
Share
Expand All
More Forum Discussions

How to reset the tire pressure on the Volkswagen Tayron?

The method to reset the tire pressure on the Volkswagen Tayron is as follows: 1. Power on the car and turn on the ignition switch; 2. Use the buttons on the multifunction steering wheel to locate the settings interface on the car's dashboard, then press the OK button to enter the settings; 3. Use the buttons on the steering wheel to navigate to the maintenance option, then press the OK button to enter the interface; 4. Find the reset option on the interface and press the OK button; 5. A confirmation prompt to reset the maintenance cycle data will appear on the dashboard menu, press the OK button to complete the process. Taking the 2020 Volkswagen Tayron as an example, its body dimensions are: length 4589mm, width 1860mm, height 1660mm, wheelbase 2731mm, fuel tank capacity 60l, and trunk capacity 1590l.
1
5
Share

What are the causes of engine idle vibration?

The causes of engine idle vibration are: 1. The vehicle's ignition system has malfunctioned; 2. Components in the ignition system have become loose; 3. Severe carbon buildup in the engine; 4. Aging of engine components; 5. Excessive carbon buildup in the throttle; 6. The air filter has not been replaced in time; 7. Excessive carbon buildup in the fuel injectors; 8. Issues with the ignition system; 9. Unstable oil pressure. Engine idle is not a speed but a working condition. When the engine runs without load, it is called idling. When the engine is running and the accelerator pedal is completely released, the engine is in an idle state. The engine speed during idling is called the idle speed, which can be adjusted by modifying the throttle opening size, among other methods.
19
1
Share

What does an exclamation mark in the middle of the engine warning light indicate?

An exclamation mark inside the engine symbol represents the engine warning light. There are primarily 7 reasons why it illuminates: Sensor malfunction: The sensors mentioned here include coolant temperature, crankshaft position, air flow, intake temperature, oxygen sensors, etc. When these sensors are damaged, have poor contact, or experience signal interruption, the vehicle's ECU cannot accurately obtain engine data, which triggers the engine warning light. Fuel/oil quality issues: Failure to use the fuel and oil specified by the manufacturer may cause engine wear, leading to the illumination of the warning light. Poor combustion of air-fuel mixture: Poor combustion can result in engine carbon buildup or knocking. When detected by the oxygen sensor and reported to the ECU, the warning light will illuminate as an alert. Issues such as faulty spark plugs, ignition coils, fuel pumps, or clogged fuel lines can all cause poor combustion. Turbocharging problems: The intake boost piping or turbocharger can also trigger the engine warning light. The most common issue is a damaged turbocharger, often accompanied by symptoms like oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Intake problems: If the vehicle's intake system is compromised, it may lead to clogged engine piping, and in severe cases, trigger the engine warning light. A dirty air filter that hasn't been cleaned regularly can cause intake issues. Exhaust problems: Exhaust system faults can also illuminate the engine warning light. Common causes include faulty rear oxygen sensors, catalytic converters, exhaust camshafts, or bearings, with the catalytic converter being the most frequent issue. Using leaded gasoline, lead/silicon-based lubricant additives, physical damage to the catalytic converter, or fuel system malfunctions can all contribute to catalytic converter failure. Anti-theft system malfunction: If the vehicle's electronic anti-theft system fails or if there's a mismatch between the anti-theft controller and the engine control unit, the anti-theft system may prevent the engine from operating normally while also triggering the warning light. If the engine warning light illuminates, follow these steps: First, check if the engine is running normally. Look for symptoms like shaking or black smoke emission. If present, avoid restarting the engine. Note: Never restart if the red warning light is on. If the engine can be started, turn it off for 5-10 minutes. Then, without pressing the brake pedal, press the start button once or turn the key halfway to the 'ON' position (without depressing the clutch). The vehicle will enter self-diagnosis mode upon power-on. Wait 5-10 seconds to see if the warning light turns off. If the light remains on, visit a service center promptly. Technicians can use diagnostic tools to read trouble codes, identify the issue, and perform targeted repairs.
20
4
Share

How to adjust the time on a Volkswagen Sagitar?

To adjust the time on a Volkswagen Sagitar, follow these steps: 1. Press the clock button below the CD player for three seconds; 2. The dashboard will emit a beep sound; 3. When the time starts flashing, adjust it accordingly; 4. Once the time is set, press the clock button again to stop the flashing. Taking the 2021 Volkswagen Sagitar as an example, it belongs to the compact car category with the following dimensions: length 4753mm, width 1800mm, height 1462mm, wheelbase 2731mm, and a fuel tank capacity of 50 liters. The 2021 Volkswagen Sagitar features a MacPherson strut front suspension and a multi-link independent rear suspension. It is equipped with a 1.2T turbocharged engine, delivering a maximum horsepower of 112 PS, maximum power of 85 kW, and maximum torque of 175 Nm, paired with a 5-speed manual transmission.
1
1
Share

Where is the license plate 'Chuan Y' from?

Chuan Y is the license plate of Bazhong City in Sichuan Province. The license plate codes for various regions in Sichuan Province are as follows: Chuan A is Chengdu City, Chuan B is Mianyang City, Chuan C is Zigong City, Chuan D is Panzhihua City, Chuan E is Luzhou City, Chuan F is Deyang City, Chuan H is Guangyuan City, Chuan J is Suining City, Chuan K is Neijiang City, Chuan L is Leshan City, Chuan M is Ziyang City, Chuan Q is Yibin City, Chuan R is Nanchong City, Chuan S is Dazhou City, Chuan T is Ya'an City, Chuan U is Aba Tibetan and Qiang Autonomous Prefecture, etc. A license plate is the abbreviation for a vehicle license plate and a vehicle driving license. It is a hard plate with a unified format and style as stipulated by national vehicle management regulations, issued by vehicle management authorities after reviewing, inspecting, and registering vehicles that have applied for license plates, bearing a registration code.
15
1
Share

How long does it take to get a license plate for a car?

It takes three to five working days to get a license plate for a car. After selecting the number, you need to pay the fee and wait to receive the plate. The process of getting a license plate is as follows: 1. Prepare the relevant documents. For individual registration, you need to bring your ID card and a copy; for corporate registration, you need to bring the original and a copy of the company's unified social credit code business license. 2. Purchase compulsory traffic insurance from any insurance company. 3. Bring the insurance policy, customs declaration, commodity inspection certificate, and invoice to the local industrial and commercial bureau for verification and stamping. 4. Go to the local state tax bureau to pay the vehicle purchase tax. 5. Bring all the documents to the vehicle management office for stamping, taking photos, and vehicle inspection.
9
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.