Will the engine valves bend if water enters?

1 Answers
Lewis
07/29/25 2:07pm
No, water entering the engine can cause valve damage. Below is relevant information about engines: 1. Concept: An engine (Engine) is a machine capable of converting other forms of energy into mechanical energy, including internal combustion engines (reciprocating piston engines), external combustion engines (Stirling engines, steam engines, etc.), jet engines, electric motors, etc. For example, internal combustion engines typically convert chemical energy into mechanical energy. 2. Classification: Internal combustion engines, external combustion engines (where fuel burns outside the engine), gas turbines, and jet engines.
Was this review help?
9
4
Share
More Forum Discussions

What is the reason for the outer edge of the brake disc not being worn?

The reason why the outer edge of the brake disc is not being worn is introduced: The brake pads are uneven, and the brake pads should be replaced in time. Car brake pads, also known as car brake linings, refer to the abrasive materials fixed on the brake drum or brake disc that rotates with the wheel. The friction linings and friction blocks bear external pressure and generate friction to achieve the purpose of vehicle deceleration. The following is the relevant introduction about brake pads: 1. Brake pad maintenance: The braking effect of the car is determined by the brake pads, which are very important for the vehicle. Daily inspection and protection are indispensable. Under normal driving conditions, the brake shoes should be checked every 5,000 kilometers. Not only the remaining thickness should be checked, but also the wear state of the shoes, whether the wear on both sides is the same, whether the return is free, etc. Any abnormal situation must be dealt with immediately. When the thickness of the brake pads is about 0.5 cm, they should be replaced. 2. Brake pad replacement: It is best to replace the brake pads with the original spare parts provided by the manufacturer. Only in this way can the braking effect between the brake pads and the brake disc be the best, and the wear is the smallest. After replacement, be sure to step on the brakes several times to eliminate the gap between the shoes and the brake disc, otherwise, the first step may not brake, which can easily cause an accident.
10
3
Share

What is the process for reporting a car accident to insurance?

Here is the insurance process after a car accident occurs: 1. Notify the insurance company: After an insurance incident occurs, the policyholder should promptly notify the insurance company of the incident's time, location, cause, extent of losses, policy number, insured subject matter, insurance type and category, and policy duration. If the insured subject matter is damaged in a different location, the policyholder should report the incident to the original insurance company and its local branch or agent in the accident area. Before the insurance company arrives at the accident scene, the policyholder should take necessary rescue measures and organize the damaged insured subject matter. For fires or motor vehicle accidents, the policyholder should follow the on-site instructions of the fire department or traffic police at the scene. 2. Undergo insurance company inspection: The policyholder should allow the insurance company or its authorized personnel (such as insurance agents or inspection agencies) to inspect the damaged insured subject matter at the accident scene and provide all necessary assistance to ensure the insurance company accurately determines the cause of the accident and confirms the extent of damage and loss amount. 3. Submit a claim application and provide claim documents: The policyholder should submit a claim application to the insurance company in accordance with relevant laws and the insurance contract, along with the required claim documents. The policyholder should promptly report the incident to the local public security department and submit an "accident notification" to the insurance company within 24 hours of the accident.
12
0
Share

What are the main components of the valve train?

Here is an introduction to the composition and working principle of the valve train: 1. Composition of the valve train: The valve train consists of two groups: the valve drive group and the valve group. The valve drive group includes the crankshaft timing gear, camshaft timing gear, camshaft, tappet, push rod, rocker arm, valve clearance adjustment screw and lock nut, and rocker arm shaft. The valve group includes the valve, valve guide, valve spring, valve spring seat, valve oil seal, and valve seat. 2. Working principle of the valve train: When the camshaft rotates, and the base circle part of the cam is in contact with the tappet, the tappet does not rise, and the transmission parts above the tappet do not move, keeping the valve closed. When the raised part of the cam comes into contact with the tappet, it begins to lift the tappet, thereby opening the valve. When the maximum raised part of the cam contacts the tappet, the valve reaches its maximum opening. Subsequently, the raised surface of the cam in contact with the tappet begins to gradually decrease, and the valve starts to close under the action of the valve spring, reversely pushing the rocker arm and other transmission components, causing the tappet to move downward to maintain contact with the cam. When the raised part of the cam leaves the tappet, the valve is completely closed.
14
3
Share

How to Fix a Longer Brake Pedal Travel?

To restore the brake pedal travel, start the vehicle and wait for the idle speed to stabilize (about 2-3 minutes). Then, press the brake pedal firmly all the way down, hold it for two seconds, and pull up the handbrake. Keep the foot brake pressed firmly for a few more seconds without releasing it, then slowly release the foot brake and the handbrake. Below are the specific reasons for increased brake pedal travel in cars: 1. Insufficient brake fluid pressure: This can be due to a lack of fluid in the master cylinder, ruptured brake lines, leaking pipe connections, or clogged fluid passages. 2. Brake pedal malfunction: This may be caused by excessive free travel of the brake pedal or excessive clearance in the brake system, poor contact of the brake shoe friction linings, severe wear, or contamination with oil. 3. Condition of the brake discs and pads: The state of the brake discs and pads is another major reason for increased brake pedal travel. As the thickness of the brake pads and discs decreases, the brake fluid level also drops. Since brake fluid is the medium for transmitting force, greater compression is required to effectively complete the braking action, naturally leading to longer brake pedal travel. Therefore, it is essential to regularly inspect the condition of the brake discs and pads during daily use, and not wait until the dashboard warning light comes on before performing maintenance checks.
20
4
Share

How to Deal with the Abnormal Noise of Mercedes-Benz E300L on Bumpy Roads?

Over time, gaps may develop in some parts of the car body, causing friction between certain components when driving on unpaved roads or during emergency braking, resulting in abnormal noises. Below are the solutions to address these noises: 1. Body Noise: For body noise, it is recommended to visit a 4S shop to check the tightness of the chassis screws and connecting parts, and to inspect whether any components of the body are rubbing against each other. 2. Window Noise: If there is noise from the windows, roll down the glass, clean the rubber sealing strips around the window frame, and use a damp cloth to wipe between the two rubber strips until the dust is removed, which should eliminate the noise.
20
5
Share

How to Handle Difficult Steering in Vehicles with Power Steering?

Driving a vehicle with power steering that has difficulty steering should be taken to a repair station for maintenance. Below are the relevant details for checking the power system: 1. Steering gear inspection items: (1) Mechanical steering gear inspection: Check for wear and damage on the steering pinion and rack, and for cracks on the steering gear housing. Note that parts on the steering gear must not be welded or straightened; they can only be replaced. Also, inspect the wear and damage on bearings and bushings, as well as the wear and aging of oil seals and dust covers, and replace them promptly. (2) Steering damper inspection items: Check the stroke of the steering damper. The working stroke L should be the difference between the maximum length (Lmax) of 556mm and the minimum length (Lmin) of 344.5mm, which is 211.5mm. Replace if the stroke is insufficient. Check the damping force of the steering damper; the maximum damping load is 560N, and the minimum damping load is 180N (conducted on a test bench). Check if the support of the steering damper is cracked. Inspect the rubber bushings at the ends of the steering damper for damage and aging. 2. Power steering gear inspection method: Check all oil leakage points and replace all O-rings and gaskets. If there is an issue with the hydraulic distribution valve, it must be replaced entirely or the sealing rings on the distribution valve must be replaced. Check if the pinion and rack are damaged. Inspect bearings and oil seals for damage. Check the dust cover for damage and aging. Examine the steering gear housing for cracks and oil leaks.
6
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.