Will the Engine Malfunction Light Illuminate When the Battery is Dead?

1 Answers
VonLeo
07/25/25 10:04am
A dead battery can generally cause the engine malfunction light to illuminate. The reason the engine malfunction light comes on after a battery discharge may be due to the fault codes generated. These codes can initially be cleared at a 4S shop. If the fault codes reappear afterward, a professional inspection and repair will be necessary. Below is a relevant introduction: Meaning of the engine malfunction light: During vehicle operation or at the moment of ignition, the engine malfunction light on the dashboard—typically red or yellow—illuminates. In most cases, it does not disappear automatically, though it may in rare instances. This is referred to as the engine malfunction light being on. The engine malfunction signal is issued by the ECU (Engine Control Unit), which controls all electronic components of the engine, including the electronic throttle, fuel injectors, alternator, fuel pump, and more, covering systems such as intake, exhaust, fuel, ignition, and timing.
Was this review help?
17
3
Share
More Forum Discussions

How to Remove the Rear Seats of a Kia K3?

The steps to remove the rear seats of a Kia K3 are as follows: 1. First, unscrew the two M12 flange bolts (commonly referred to as 12mm hex bolts) securing the seat cushion. 2. The specific locations of these two bolts are along the centerline below the seat back, at the gap between the seat cushion and the backrest. 3. Next, release the two clips at the front of the seat cushion by pulling upward firmly. 4. To remove the backrest, unscrew the two M12 flange bolts located on each side at the lower part of the seat back. 5. It is recommended to have two people for this step: simultaneously pull the lower part of the backrest outward to gradually loosen it, then lift the entire backrest upward as there are clips on both sides near the windows and one in the middle.
1
1
Share

What are the symptoms of a bad lower control arm ball joint?

The symptoms of a bad lower control arm ball joint are as follows: 1. The tires will swing abnormally during driving, causing abnormal tire wear and increased noise. 2. When the car is driving at high speed, the steering wheel will shake, and there will be noise from the chassis when driving on bumpy roads. 3. There will be a "clicking" sound from the steering wheel. Since the lower control arm is part of the steering system, a damaged lower control arm bushing directly leads to abnormal vehicle dynamics, causing the vehicle to pull to one side, increased wear affecting steering control, which is very detrimental to safety. It is recommended to go to a repair shop for relevant inspections and perform a four-wheel alignment after adjustments.
12
1
Share

Where is the fuel tank cap switch of the Langdong?

The fuel tank cap switch of the Langdong is located under the driver's seat near the door side, where there are two pull switches: one for the fuel tank and the other for the trunk. Here are some related introductions about the Langdong: 1. Interior facilities: Equipped with a large-screen DVD intelligent navigation, dual-barrel instrument panel, and dual-zone automatic air conditioning. 2. Power system: Powered by a 1.6L γ engine and a 1.8L Nu engine. The transmission options include a 6-speed manual and a manual-automatic integrated transmission. 3. Body dimensions: The length, width, and height are 4570mm, 1775mm, and 1445mm respectively, with a wheelbase of 2700mm.
8
1
Share

Where is the air conditioning filter located in the Qashqai?

The air conditioning filter in the Qashqai is located near the left foot area of the front passenger seat. Below are the steps for replacing the Qashqai's air conditioning filter: 1. Remove the decorative panel on the right side of the driver's seat. It's easier to start from the top and work your way down. 2. The filter cover is connected to a gray sealing sponge and has a handle in the middle. The bottom of the cover has a clip; use your finger to pull it, and the cover will come off. 3. After removing the cover, you can pull out the air conditioning filter. Note: The filter has a front and back side. While original equipment manufacturer (OEM) filters have markings indicating front and back, other filters may have a thin extra material on the short edge of the frame to distinguish the sides. 4. Installing the filter can be challenging, mainly due to the awkward position. You can bend the filter toward the front of the car and, once fully inserted, pull it back and forth a few times to ensure it's properly seated. Finally, replace the cover. Without an air conditioning filter, particles can enter the cabin, contaminating the car's air conditioning system and reducing the cooling system's performance. Inhaling dust and harmful gases can cause allergic reactions, lung damage, and irritation from ozone exposure, along with unpleasant odors, all of which can affect driving safety. A high-quality air filter can capture fine particles, reduce respiratory discomfort, minimize irritation for allergy sufferers, enhance driving comfort, and protect the air conditioning and cooling system.
5
4
Share

Why does car tire pressure gradually decrease?

Car tire pressure gradually decreases for the following reasons: 1. The vehicle has not been driven for a long time. 2. The tire has a slow leak. If the tire pressure is insufficient, it needs to be inflated immediately to avoid operating the tire under low pressure, which can affect the car's handling and the tire's lifespan. If the tire pressure is too high, the contact area between the tire and the ground decreases, reducing the tire's grip and consequently affecting the car's driving stability and handling. If the tire pressure is too low, it can cause the tire to develop wave-like deformation during high-speed driving, accelerating tire aging and increasing the risk of a blowout.
7
1
Share

What does the C gear in Mercedes-Benz mean?

Mercedes-Benz's C gear stands for C mode, which is Comfort mode. Below is a related introduction about Mercedes-Benz gear modes: 1. Mercedes-Benz has five driving modes: E mode, which is ECO (Economy) mode; C mode, which is Comfort mode; S mode, which is Sport mode; S+ mode, which is Sport+ (Extreme Sport) mode; and I mode, which is Individual (Custom) mode. 2. When the gear is in C mode, the car starts in 2nd gear. The transmission control module shifts to higher gears at lower RPMs, resulting in smoother gear shifts, better comfort, and improved fuel efficiency. 3. When the gear is in S mode, the car starts in 1st gear. The transmission control module automatically selects the RPM for maximum torque output before shifting, making it suitable for high-speed cornering.
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.