Will the car stall if water enters the exhaust pipe?

1 Answers
KendraLee
07/29/25 1:41pm
Water entering the exhaust pipe can cause the car to stall. Water in the exhaust pipe may lead to exhaust blockage, and poor exhaust flow can result in engine stalling, although the engine itself may not necessarily take in water. Estimated impact on the vehicle: In addition to understanding the underwater conditions clearly, it is also necessary to make a rough assessment of the difficulties based on the vehicle being driven. First, observe whether the accumulated water will reach the floor inside the cabin or the exhaust pipe. Second, check if the water level exceeds the midline of the tires. If either of these two standards is exceeded, it is likely to cause severe damage to the vehicle's engine, computer, and other components. Conditions for water damage insurance coverage: Not all cases of water exposure will result in insurance compensation. If the vehicle is damaged due to improper operation leading to water ingress, the insurance company will not cover the claim.
Was this review help?
10
5
Share
More Forum Discussions

Should You Turn Left or Right First When Parallel Parking?

Maintain a distance of approximately 30 centimeters between the right side of the car body and the edge of the parking space. Drive straight to the starting line, then begin reversing while observing the right rear-view mirror. When the front line of the parking space disappears from the rear-view mirror, turn the steering wheel fully to the right and continue reversing. Upon seeing the inner corner of the parking space, turn the steering wheel one full rotation to the left and continue reversing. When the left rear tire is about to touch the dashed line of the parking space edge in the left rear-view mirror, turn the steering wheel one more full rotation to the left while simultaneously observing both left and right rear-view mirrors.
5
2
Share

What are the soft passing methods for Subject 2 driving test?

Maintaining a calm mindset during the test is the most reliable guarantee for passing. First and foremost, be confident, as confidence allows your driving skills to be demonstrated normally. Mastering the technical essentials proficiently is the fundamental requirement for passing the test. Understanding the test requirements clearly is the prerequisite for passing the test. Don't practice driving just for the sake of practicing.
16
5
Share

How is the vehicle body crossing the line determined in Subject 2 test?

Before the vehicle enters the right-angle turn, it should drive close to the right side, maintaining a distance of about 0.1 meters between the right wheels and the right edge of the road. When entering the "S" curve, the vehicle should enter the curve from the right side of the road and maintain a uniform low speed. During parallel parking, maintaining an upright sitting posture is crucial for accurately judging various reference points. Turn on the right turn signal, steer the wheel appropriately to the right, and drive slowly along the right side of the road, paying attention to the distance between the vehicle body and the right edge line.
17
2
Share

What is the method to reset the maintenance light on Landwind X7?

Hold the button on the end of the wiper stalk, and the SET message will appear on the instrument panel. Release the button and press it again. Wait until the number 5000 km appears on the screen, then release the button and turn off the vehicle. Restart the vehicle to complete the maintenance light reset for the Landwind X7.
7
4
Share

How to Treat VOC Waste Gas?

Catalytic combustion is more suitable for the purification of high-concentration, small-airflow waste gas, but the promotion and use of this method are somewhat limited. This method utilizes the physical and chemical properties of pollutants, using water or chemical absorption liquids to absorb and remove waste gas. This method involves passing the pollutants through an adsorption tower filled with adsorbent, leveraging the strong adsorption capacity of the adsorbent for the pollutants. Currently, photocatalytic technology is difficult to apply on a large industrial scale and is mostly limited to experimental research and small-airflow applications.
6
3
Share

How to Reset the Anti-Pinch Protection for BMW Windows?

Setting the window initialization can reset it. If the window cannot automatically rise when closing the door, it is necessary to check the window relay. Generally, the anti-pinch protection function for windows cannot be canceled. Due to safety considerations during factory settings, this function is mandatory and cannot be canceled.
2
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.