Will the Car Move When Releasing the Brake in an Automatic Transmission?

1 Answers
AndresAnn
07/29/25 10:57pm
Relevant information is as follows: 1. Before starting, you need to press the brake. Press the clutch pedal all the way down with your left foot, press the foot brake with your right foot, shift into 1st gear, release the handbrake, slowly release the clutch until you feel a noticeable vibration in the car body, then release the foot brake, and the car will start moving. 2. When starting on a slope, the clutch, accelerator pedal, and parking brake lever need to be coordinated. The timing of releasing the parking brake lever is crucial; if it's too late, the car won't start, and the engine will stall. 3. The technique to master when lifting the clutch pedal to the semi-engagement point: listen to the engine sound, feel the car body shaking, and watch the tachometer needle trembling and moving downward.
Was this review help?
13
2
Share
More Forum Discussions

What is the sequence for engaging the handbrake and shifting gears?

The sequence for starting a car is to shift into first gear, release the handbrake, gently press the accelerator, and slowly lift the clutch. The sequence for stopping a car is to press the brake to bring the vehicle to a halt, shift to neutral, engage the handbrake, and then turn off the engine and exit the vehicle. For automatic transmission cars, when parking, first shift into P (Park) mode, then firmly engage the handbrake. With automatic transmission models, it is acceptable to either engage the handbrake first or shift into P mode first when parking. For manual transmission models, when parking, you can also first press the clutch pedal, then firmly engage the handbrake, and finally shift into neutral. The starting sequence is the same for both automatic and manual transmissions: shift into gear first, then release the handbrake. Once the gear is engaged, the transmission's power delivery path is connected. When first shifting into gear, the transmission is in first gear, which provides the highest torque. If the brake is not properly engaged, the car may suddenly lurch forward. Below are some braking techniques for manual transmission cars: Braking on curves: Always brake before entering a curve to reduce speed, then accelerate when exiting the curve. If you need to brake while turning, adjust the braking force according to the vehicle's arc to avoid skidding or drifting. Smooth braking: Brake early and press the pedal slowly. As the vehicle comes to a stop, gradually release the brake pedal, then fully release it once the vehicle has stopped.
18
2
Share

How to Conduct Annual Inspection for Motorcycle Driving License?

Motorcycle driving licenses require annual inspection every 6 years. Below are the specific details about the annual inspection: 1. Required documents for license renewal: Original copy of the driving license, ID card, and medical certificate for motor vehicle drivers. 2. Article 7 of Chapter 2 stipulates: The validity period of a driving license is 6 years. The first year after initially obtaining the license is the probation period; the validity period of a learner's license is 2 years; the validity period of a temporary license does not exceed 1 year. Although drivers with A, B, N, and P licenses are no longer required to undergo annual inspection during the validity period, they must visit the Vehicle Management Section of their local traffic police branch within 15 days of the original annual inspection deadline to obtain the "Motor Vehicle Driving License Application Form," fill it out as required, attach a photo, undergo a medical examination at a hospital, and then submit the form back to the Vehicle Management Section for computer confirmation.
15
2
Share

How does a car refrigerator use electricity in a vehicle?

Car refrigerators are powered by connecting to the car battery or an external power bank. A car refrigerator refers to a portable cooler that can be carried in a vehicle. There are mainly two types of car refrigerators on the market: one is a semiconductor car refrigerator, which operates based on electronic chip cooling; the other is a compressor car refrigerator, which uses traditional compressor technology found in conventional refrigerators and provides lower cooling temperatures. After the car is turned off, the car refrigerator operates in the following two scenarios: 1. If the car cigarette lighter continues to supply power: the refrigerator will keep running and automatically activate the battery protection function. When the power level drops below the system-set value, it will automatically disconnect the circuit, stop operating, and enter a heat preservation state. 2. If the car cigarette lighter stops supplying power: the refrigerator will automatically stop operating and enter a heat preservation state.
1
3
Share

Where is the air conditioning filter located in the Haima M6?

Haima M6 air conditioning filter is located inside the glove compartment on the passenger side. You can see it after removing the glove compartment. Generally, the air conditioning filter should be replaced every 10,000 kilometers. If the air conditioning filter is not replaced for a long time, it will affect the performance of the air conditioning system and the health of the passengers. Here are the steps to replace the air conditioning filter: 1. Locate the position of the filter on the passenger side inside the car. 2. Gently remove the glove compartment. 3. Take out the old air conditioning filter and replace it with a new one. 4. Reinstall the glove compartment back into place.
12
2
Share

What does 909012 mean for tires?

909012 tire means a width of 90mm, an aspect ratio of ninety percent, a radial tire thickness of 81mm, and a rim size of 12 inches. Below is an introduction to tires: 1. Functions of tires: Mainly include dry grip, hydroplaning resistance, providing comfort, reducing driving noise, impact resistance, wet grip, load-bearing capacity, handling ability, average wear, and mileage. 2. Tire cross-section structure: Generally can be divided into 4 parts: tread, shoulder, sidewall, and bead. Each part has its own function. The tread mainly contacts the ground, the shoulder and sidewall provide support, and the bead contacts the rim to provide sealing. 3. Internal composition of tires: The inside of the tire is composed of multiple layers of different materials, including tread pattern, overlay, steel belt, stress absorption rubber strip, carcass ply layer, and inner liner.
8
4
Share

How to replace the brake light stopper on the Tiggo 3?

Replacement method for the Tiggo 3 brake light stopper: Press the brake pedal to the bottom, use a jack to lift the vehicle, then remove the stopper above the brake pedal and replace it with a new one. Additional information about the Tiggo 3 is as follows: 1. The Tiggo 3 features a new textured and stylish interior, offers authentic urban off-road SUV driving control, and comes equipped with the latest Cloudrive 2.0 intelligent cloud-connected driving system, fully meeting the demands of young consumers for an urban SUV. 2. The Tiggo 3 adopts a piano black finish for its stylish and dynamic front grille, along with newly designed eagle-eye headlights, complemented by dual five-spoke 17-inch aluminum alloy wheels, giving the overall exterior a more youthful and dynamic appearance.
18
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.