Will the Car Chassis Rust When Driving in Rainy Days?

2 Answers
McEmily
07/29/25 7:48am
As long as the car body is made of metal, it will undergo oxidation reaction with oxygen in a humid environment, leading to rust. To prevent rust, the following measures should be taken: 1. Block direct contact between metal and air: Manufacturers use primer and topcoat to protect the entire car body, completely isolating the metal from oxygen. Currently, electrophoretic primer and electrostatic mechanical spraying processes are widely adopted to minimize dead corners that manual spraying cannot reach. 2. Improve the purity of the metal as much as possible: Conductive impurities in the metal are the root cause of electron migration, and differences in potential will lead to electrolytic reactions, resulting in rust of the metal acting as the negative electrode. Therefore, metals with higher purity are less prone to rust. Mazda cars install zinc plates in areas prone to corrosion on the car body, using the zinc plate with lower potential as the negative electrode. After rusting, timely replacement of the zinc plate can delay the rusting of the car body steel, achieving the goal by transferring the negative electrode of the electrolytic reaction.
Was this review help?
3
1
Share
McZoe
08/12/25 11:03am
Honestly, it's quite common for car chassis to rust on rainy days. Rainwater contains impurities and acidic substances that can seep into chassis gaps, accelerating metal corrosion. After driving for several years, I've noticed the chassis always stays damp after rain, especially on older models without rust-proof paint - once rust spots appear, they're hard to control. Most modern cars come with protective coatings from the factory, but if road pebbles chip off even a small section, rainwater can cause serious damage. A friend's car ended up with a rusted-through exhaust pipe from long-term neglect of small rust spots, costing thousands in repairs. I recommend checking the chassis before and after rainy seasons, and using a high-pressure hose to clean dirt from hard-to-reach areas after car washes to extend its lifespan. Chassis rust isn't just unsightly - it affects safety too, like when rusty suspension systems cause instability during braking. Don't underestimate this; developing good maintenance habits can save both hassle and money.
Was this review help?
5
3
Share
Expand All
More Forum Discussions

What is the battery model for Mazda 6?

The original battery is a Fengfan battery with a capacity of 68AH. Below is relevant information about the battery: 1. Principle: The car battery, also known as the storage battery, works by converting chemical energy into electrical energy during the driving process. Generally, the lifespan of a car battery ranges from 1 to 8 years, with the exact duration closely related to the car's usage conditions. Common domestic battery brands include Feifan, Zhengye, and Fengfan, with prices ranging from 200 to 1000 yuan. 2. Timely Charging: Under normal usage conditions, a car battery typically lasts more than three years. If you notice that the battery cannot hold a charge or experiences weak performance during online startup, it should be removed and charged for 12 to 24 hours. If the battery still shows weak performance after charging, consider replacing it.
18
5
Share

What is a Three-Way Catalytic Converter?

A three-way catalytic converter is the most important external purification device installed in a vehicle's exhaust system. Related introduction: 1. Overview: The three-way catalytic converter, installed in a vehicle's exhaust system, is the most crucial external purification device. It converts harmful gases such as carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxides (NOx) emitted from vehicle exhaust into harmless carbon dioxide, water, and nitrogen through oxidation and reduction reactions. Since this converter can simultaneously transform the three main harmful substances in exhaust gases into harmless substances, it is called a three-way catalytic converter. 2. Function: It transforms harmful gases like carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxides (NOx) emitted from vehicle exhaust into harmless carbon dioxide, water, and nitrogen through oxidation and reduction reactions.
6
2
Share

What are the differences between the 2007 and 2008 Crown models?

The differences between the 2007 and 2008 Crown models mainly lie in one aspect: the 2007 Crown offers two powertrain combinations, while the 2008 Crown only has one. Specific details are as follows: 1. The additional powertrain combination in the 2007 model is: equipped with a 3.0-liter V6 naturally aspirated engine, paired with a 6-speed automatic manual transmission, delivering a maximum power of 170KW, maximum horsepower of 231PS, and maximum torque of 300N·m. 2. Both the 2007 and 2008 models share a common powertrain combination: equipped with a 2.5-liter V6 naturally aspirated engine, matched with a 6-speed automatic manual transmission, producing a maximum power of 145KW, maximum horsepower of 193PS, and maximum torque of 236N·m.
17
2
Share

What is the trick to releasing the clutch without stalling?

The key points to releasing the clutch without stalling can be summarized as follows: 1. Master the technique: Release the clutch slowly when releasing the handbrake. Keep the throttle as large as possible, meaning do not release the throttle pedal when releasing the handbrake. Finally, release the handbrake quickly, i.e., when reaching the semi-engagement point, the handbrake should follow. 2. Handling a stall: If the car stalls suddenly while going uphill, do not panic. Stay calm, pull the handbrake, and press the brake to control the car from sliding back. If the car stalls during a hill start, when restarting, shift into first gear and press the clutch all the way down; then slowly lift the clutch to the semi-engagement state. The advantage of using first gear is that it provides sufficient power and is less likely to stall. Maintain an appropriate speed; excessive speed can cause significant body vibration.
7
4
Share

How to Paint Plastic for Maximum Adhesion?

To ensure paint adheres firmly to plastic, first apply a coat of plastic primer, provided the plastic surface is smooth and even. Related information: 1. Introduction: Paint is a type of synthetic coating made from nitrocellulose, resins, pigments, and solvents. It is typically sprayed evenly onto surfaces using a spray gun, offering water resistance, oil resistance, quick drying, and is used for automobiles, aircraft, woodwork, leather, etc. 2. Precautions: This substance is toxic and can have certain effects on the body. The toxicity varies among different brands of paint due to differences in composition and content. Special attention should be paid to safety during use to avoid inhalation and skin contact.
1
2
Share

What are the three transmission methods of camshafts?

There are three transmission methods for camshafts: cylindrical gear transmission, bevel gear transmission, and chain transmission. High-performance engines in mid-to-high-end cars and trucks generally use chain or cylindrical gear transmission to ensure the accuracy of valve timing. Cylindrical Gear Transmission: Most overhead camshafts and underhead camshafts use cylindrical timing gear transmission, where the crankshaft gear meshes with the camshaft gear through an intermediate gear. Timing gears are mostly helical to ensure smooth meshing and reduce noise. The gears are made of steel or cast iron. This method is simple in structure, easy to disassemble and assemble, and reliable in process. Bevel Gear Transmission: This method is commonly used in lightweight, high-speed, high-power internal combustion engines with overhead camshafts. The camshaft is far from the crankshaft, and bevel gears and vertical elastic shafts are used for transmission. It is compact and reliable in structure but inconvenient to disassemble and assemble. Chain Transmission: Chain transmission is mostly used in overhead camshaft valve mechanisms, which can protect the valve mechanism from inertial loads. This device requires high-quality chains, and the chains must maintain a certain tension during operation. It is equipped with a tensioner sprocket, and adjusting the position of the tensioner sprocket can change the chain tension. It has good operational reliability but is less durable than gear transmission devices.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.