Will Pouring Water into the Exhaust Pipe Damage the Car?

1 Answers
MacAngelina
07/30/25 3:00am
Pouring water into the exhaust pipe will not damage the car. However, water entering the exhaust pipe can cause blockages, leading to poor exhaust flow and potential engine stalling. The following are methods for maintaining the exhaust pipe: 1. Regularly inspect the exhaust pipe: Generally, a comprehensive inspection of the exhaust pipe can be costly, so it's advisable to visit a regular repair shop for an initial check. The main purpose is to identify any damage to the exhaust pipe. If any cracks are found, immediate repairs are necessary to avoid affecting normal vehicle operation. 2. Prevent the muffler from rusting: Since the muffler is located in the middle of the exhaust system, any issues with it can affect the entire exhaust system. The primary preventive measure is to avoid water entering the muffler. During rainy days or when washing the car, be cautious to prevent water from entering the muffler. If water accidentally enters, start the engine and let it idle for about 10 minutes to expel the accumulated water. 3. Prevent exhaust pipe leaks: When installing the muffler, ensure it is properly and securely installed to avoid leaks. A leaking muffler can cause excessively loud exhaust noises and yellowing at the muffler's joints. Additionally, avoid driving at low gears with heavy loads, as this can cause varying degrees of damage to both the engine and the muffler.
Was this review help?
20
4
Share
More Forum Discussions

Is the Chevrolet Cruze a Domestic or Joint Venture Car?

Chevrolet Cruze is a joint venture car, which belongs to the American Chevrolet brand and is a product of SAIC General Motors Group in China. The body dimensions of the Cruze are 4614mm in length, 1798mm in width, and 1485mm in height, with a wheelbase of 2640mm. The Cruze is equipped with two engines: one is a 1.0-liter turbocharged engine, and the other is a 1.3-liter turbocharged engine. The 1.0-liter turbocharged engine has a maximum power of 92kw and a maximum torque of 170nm, with a maximum power speed of 5600 revolutions per minute and a maximum torque speed ranging from 2000 to 4000 revolutions per minute.
12
0
Share

How to Clean a Car Air Conditioning Condenser?

Methods for cleaning a car air conditioning condenser: 1. Dilute detergent with water; 2. Start the car and turn on the air conditioning to activate the electric fan; 3. After the entire condenser is wet, spray the diluted detergent onto the condenser surface using a water-spraying tool; 4. Restart the air conditioning to rotate the fan, and rinse thoroughly with plenty of water—the more thorough, the better. Function of the car condenser: It dissipates heat and cools the high-temperature, high-pressure refrigerant vapor discharged by the compressor, condensing it into a high-pressure liquid refrigerant. It cools and liquefies the high-pressure, high-temperature gaseous refrigerant sent from the compressor. The condenser is a component that continuously compresses the refrigerant from gas to liquid, a process of condensation and heat dissipation.
1
5
Share

What engine does the Mazda 8 use?

The Mazda 8 uses two engines in total, one is a 2.3-liter naturally aspirated engine, and the other is a 2.5-liter naturally aspirated engine. The 2.3-liter naturally aspirated engine has a maximum power of 154 horsepower and 205 Nm of torque. This engine can deliver maximum power at 6,500 rpm and maximum torque at 4,000 rpm, paired with a 4AT transmission. The 2.5-liter naturally aspirated engine has a maximum power of 163 horsepower and 226 Nm of torque. This engine can deliver maximum power at 6,000 rpm and maximum torque at 4,000 rpm, paired with a 5AT transmission.
2
5
Share

How Many Times Can You Retake Subject 2?

Subject 2 can be retaken a maximum of five times. If you do not attend the retake or fail the retake, the current exam session will be terminated, and the applicant must reschedule the exam. Both Subject 2 and Subject 3 exams can be rescheduled after ten days. Within the validity period of the driving skill test permit, the number of retakes for Subject 2 and Subject 3 road driving skill tests cannot exceed five. If you still fail the fifth retake, the results of other subjects that have been passed will be invalidated. For small vehicles C1 and C2, the Subject 2 test includes five items: reversing into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and driving on a curve.
9
4
Share

How tall is a standard 200-liter oil drum?

200L oil drum dimensions are generally: approximately 930mm in height and 580mm in diameter. The capacity is about 53 gallons. This type of oil drum can be reused multiple times. Below is more information about oil drums: 1. Introduction: An oil drum, which is a barrel used for holding oil, is usually made of iron or plastic in a cylindrical shape. It was initially invented by Germans on the eve of World War II, primarily for transporting an important military resource—gasoline. It is a typical product of war. 2. Leak prevention measures: Regularly inspect oil drums for corrosion, bulging, defects, dents, or leaks. Place defective oil drums in an independent secondary containment barrel or a leak emergency barrel; ensure that the oil drum is compatible with its contents. For example, do not store acids in ordinary iron drums or solvents in plastic drums. 3. Storage function: If oil drums are to be stored outdoors, ensure that rainwater does not enter. By wrapping spill containment pallets, spill containment platforms, or IBC spill containment pallets with waterproof tarps in the aforementioned secondary containment measures, the purpose of preventing rainwater, sun exposure, and keeping insects and birds out of the packaging container can be achieved.
11
1
Share

How Often Should the Gear Oil in an Electric Vehicle Be Changed?

Electric vehicle gear oil should be changed every two years. Below is more information about gear oil: 1. Function: Gear oil primarily refers to the lubricating oil for transmissions and rear axles. It differs from engine oil in terms of usage conditions, composition, and performance. Gear oil mainly serves to lubricate gears and bearings, prevent wear and corrosion, and assist in heat dissipation for gears. 2. Introduction: Gear oil should have excellent anti-wear and load-bearing properties, as well as appropriate viscosity. Additionally, it should possess good thermal oxidation stability, anti-foaming properties, water separation performance, and rust prevention. 3. Classification: Gear oil is divided into two categories: automotive gear oil and industrial gear oil. The former is used to lubricate various manual transmissions and gear drive shafts in vehicles, while the latter is used for lubricating gear devices in industries such as metallurgy, coal mining, cement, and chemical processing.
11
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.