Will points be deducted if the speed falls below 20 km/h in Subject 3?

2 Answers
McLeilani
07/24/25 5:10pm
Points will be deducted. Relevant details are as follows: 1. Reason for deduction: In Subject 3, the matching speed for third gear is generally between 25 km/h and 35 km/h, with a minimum not lower than 20 km/h and a maximum not exceeding 40 km/h. Once these thresholds are exceeded, there is a buffer period of 5-8 seconds for gear shifting. As long as the corresponding speed is restored within the specified time, no points will be deducted. 2. Test content: The road driving skills test for Subject 3 typically includes: pre-driving preparation, simulated lighting test, starting, driving straight, gear shifting operations, changing lanes, pulling over, proceeding straight through intersections, turning left at intersections, turning right at intersections, passing pedestrian crossings, passing school zones, passing bus stops, meeting oncoming vehicles, overtaking, making U-turns, and nighttime driving.
Was this review help?
18
2
Share
McCourtney
08/11/25 9:31am
Last time I took the driving test (Subject 3), I paid special attention to the issue of speed. From my experience, driving below 20 km/h might result in penalty points, depending on the actual situation, such as whether it's during traffic congestion or on special road sections. If you drive at a consistently low speed during the test without a reasonable explanation, the examiner may easily consider your driving as unskilled or unsafe. Take my case for example—during practice, my instructor repeatedly emphasized that maintaining a speed between 25 and 40 km/h is most appropriate, as going too high or too low is unacceptable. Once, while making a turn, I got too nervous and slowed down to around 18 km/h, and was warned that such dangerous operation could cost me points. So during the actual test, I kept a close eye on the speedometer to control my speed and avoid unnecessary slowness. Additionally, the test rules mention that speed control should adapt to traffic conditions—driving too slowly may obstruct others, which is a common reason for penalties. I suggest that students preparing for the test simulate real road conditions more often, practice throttle control, and minimize mistakes.
Was this review help?
6
2
Share
Expand All
More Forum Discussions

What are the impacts of a failed small car catalytic converter?

The catalytic converter, as the most crucial component in the gasoline vehicle exhaust purification system, transforms exhaust emissions to meet environmental standards. The impacts of a failed small car catalytic converter are as follows: 1. Increased exhaust pollution: Without the catalytic converter's ability to catalytically reduce harmful gases in the exhaust, vehicle emissions will significantly worsen. 2. Engine warning light activation: When the engine's electronic control unit (ECU) fails to detect or detects abnormal signals from the oxygen sensor, the engine warning light will illuminate. 3. Increased fuel consumption and reduced power: Damage to the catalytic converter will affect the normal signal from the oxygen sensor, leading to inaccurate fuel injection control by the engine, resulting in higher fuel consumption and decreased power. 4. Carbon buildup: As the air-fuel ratio of the combustible mixture in the cylinders becomes severely imbalanced, incomplete combustion will cause excessive carbon deposits to accumulate in the cylinders, increasing the risk of chronic engine issues.
20
2
Share

What is the Difference Between an Air Filter and a Cabin Air Filter?

There are the following differences between an engine air filter and a cabin air filter: 1. The cabin air filter is installed near the air conditioning intake, specifically behind the blower motor, and is used to filter the quality of air entering from inside or outside the vehicle. 2. The engine air filter refers to the engine intake system, which filters the air entering the engine intake pipe. Their functions are different. Generally, the replacement cycle for the engine air filter is based on air quality and mileage, while the cabin air filter is typically replaced once a year or every 20,000 kilometers. 3. To access the engine air filter, open the vehicle's front hood. It is usually located on the right side facing the engine. Simply use a screwdriver to remove the fixing screws on the air filter box to see the air filter. 4. To access the cabin air filter, open the glove compartment on the passenger side, remove the cover plate, and you will find the cabin air filter. 5. The cabin air filter filters the air entering the cabin from outside, improving air cleanliness by removing impurities and other particles. This provides a good air environment for passengers and protects their health.
19
5
Share

What are the signs of a faulty front oxygen sensor?

When the front oxygen sensor fails, the ECU cannot obtain information about the oxygen concentration in the exhaust pipe, and thus cannot perform feedback control on the mixture concentration. This leads to increased fuel consumption and exhaust pollution, and the engine may exhibit symptoms such as unstable idling, misfiring, and surging. Here is some additional information about the front oxygen sensor: 1. The main function of the front oxygen sensor is feedback. Simply put, it detects the oxygen content in the exhaust gas produced after the combustion of the air-fuel mixture in the cylinders. Generally, a high oxygen content indicates a lean mixture, while a low oxygen content indicates a rich mixture. The front oxygen sensor sends different electrical signals to the ECU based on the oxygen content, allowing the ECU to adjust the mixture accordingly. 2. The exhaust gas produced by the car's combustion must pass through the catalytic converter for purification before being released. The rear oxygen sensor detects the oxygen content in the purified exhaust gas and feeds it back to the ECU. The computer then compares the data from the front oxygen sensor. If the data from the front and rear oxygen sensors are the same, it can be concluded that the catalytic converter has failed.
10
4
Share

How to Perform Pressure Testing on a Car Air Conditioning System?

Here’s how to perform pressure testing on a car air conditioning system: 1. Check the pressure in the car: First, rotate the needle valve on the DIY refill hose opener counterclockwise to its highest position, then screw the refrigerant can into the opener and tighten it. 2. Locate the low-pressure port: Typically, there’s a small blue or black cap under the hood on the left side with an "L" marked on it. Unscrew this cap. 3. Start the car engine and turn on the AC switch, setting the blower to maximum. Wait for three minutes, then connect the DIY hose to the car’s air conditioning low-pressure port. 4. Once the DIY hose is connected to the low-pressure port, the pressure gauge on the DIY hose will immediately show a reading. 5. At this point, the refrigerant refill for the car’s air conditioning system is complete. Simply tighten the "L" cap.
16
1
Share

What is the best method to judge the distance between vehicles?

Methods for judging the distance between vehicles are as follows: 1. Determine the distance of the rear vehicle to assess whether a lane change is possible. Observe how far the vehicle in the adjacent lane is located behind the side of your vehicle, typically using the side rearview mirrors. When using the rearview mirror to judge the distance, first adjust the vehicle seat and the angle of the rearview mirror. If the body of the rear vehicle has entered the danger zone to the left of the dotted line in the rearview mirror, it indicates that the distance between the vehicles is very close, and turning should not be attempted at this time. 2. Since the driver is positioned on the left side of the vehicle, it is more challenging to gauge the situation in the right lane. Moreover, the blind spot in the left side rearview mirror is larger than that on the right. If the rear vehicle occupies half of the rearview mirror's area and only half of its body is visible, it means the rear vehicle is very close to your car. In this case, you should maintain your current lane and avoid changing lanes.
15
1
Share

What are the differences between China 5 and China 6 standards?

The main difference between China 5 and China 6 standards lies in their emission requirements, with China 6 being significantly stricter. The specific differences are as follows: 1. Different emission limits: The China 6 standard imposes 40% to 50% stricter limits compared to China 5. 2. Different decommissioning timelines: For example, while both China 5 and China 6 vehicles purchased in January 2019 may have a 15-year registration period, their actual usage lifespans will differ. 3. Price difference: China 6 vehicles incorporate additional components compared to China 5 models, plus automakers face extra costs from compliance testing, certification, and production changes - making China 6 vehicles substantially more expensive. 4. Different sulfur content requirements: China 5 allows up to 10mg per kilogram, while China 6 permits up to 50mg per kilogram.
7
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.