Will points be deducted if the license plate anti-theft cap is not installed?

3 Answers
JaxonDella
07/25/25 9:23am
No points will be deducted. As long as all eight screws are installed on both the front and rear plates, traffic police will not deduct points, and the vehicle will pass the annual inspection smoothly. Points deduction related to license plate installation mainly occurs due to missing screws or failure to install them as required. If caught, the penalty will be for "failing to display the motor vehicle license plate as required," with a fine of 200 yuan imposed by the traffic management department, and in severe cases, 12 points may be deducted. More details are as follows: 1. Difficulty in installing the license plate anti-theft cap: There are two main reasons why the anti-theft cap may not fit. The first is that the base of the anti-theft cap was not screwed into the bolt before installation. If the base is not screwed in, the cap cannot be installed. The other reason is that the spring inside the cap is too protruding, preventing it from connecting with the base during installation. In this case, a small flathead screwdriver can be used to press the spring inward before installation. A useful tip for installing the anti-theft cap is to try screwing it into the base from left to right. 2. Function of the nuts: The nuts sent with the license plate are generally used with screws to secure them. However, most vehicle models come with nuts pre-installed from the factory, so these additional nuts may not be needed. Besides installing screws and nuts, anti-theft nuts should also be installed. These anti-theft nuts are sent along with the license plate. After installing the screws, the anti-theft nuts can be attached, making it impossible to remove the license plate without cutting the screws, thus achieving an anti-theft effect.
Was this review help?
15
0
Share
KarterFitz
08/11/25 2:10pm
I remember once when I was driving, I forgot to fasten the anti-theft cap, and as a result, the license plate wasn't securely fixed. It got blown askew by the wind, and at a checkpoint, the police directly deemed it as obscuring the license plate. I was immediately penalized with 6 points deducted and a fine of 200 yuan. Later, my insurance premium even increased. As an ordinary person who has been driving for many years, I deeply realize that any small oversight can amplify the consequences. The purpose of the anti-theft cap is to prevent the license plate from being stolen, but if it's not fastened properly, it can make the license plate appear incomplete, which is considered a violation under traffic laws and can result in points deduction and fines. I recommend checking it every time after maintenance or car washing, using a small tool to tighten the screws. Don't be lazy like I was and suffer the consequences. Maintain safe driving habits.
Was this review help?
1
1
Share
Expand All
LenaLynn
09/27/25 7:36am
A loose license plate anti-theft cap is no trivial matter. If it becomes loose or shifts while driving, it may partially obscure the license plate, affecting its clarity. This can easily be interpreted by traffic police as intentional concealment, typically resulting in a 6-point deduction under traffic regulations. From a safety perspective, I remind everyone to develop the habit of using a wrench to secure it during installation and to glance at the license plate before driving to ensure it's intact. A clear license plate aids in surveillance and accident traceability, avoiding point deductions and fines. Saving time on repairs is more valuable than anything. Details determine the level of risk.
Was this review help?
13
0
Share
Expand All
More Forum Discussions

Should Shock Absorbers Be Replaced Individually or in Pairs?

Shock absorbers should be replaced in pairs. They are used to dampen the oscillations from the spring's rebound after absorbing shocks and to mitigate impacts from the road surface. The reasons for replacing shock absorbers in pairs are: 1. Shock absorbers from different batches may have varying hardness levels; 2. There can be significant performance differences between old and new shock absorbers; 3. In emergency situations requiring sudden steering, if the shock absorbers have different elasticity, it may increase the risk of vehicle rollover. The functions of shock absorbers include: 1. Buffering the movement of the vehicle's center of gravity and conserving energy; 2. Reducing wind resistance and lessening the impact of changes in the vehicle's center of gravity on the tires. The steps for replacing shock absorbers are: 1. Remove the shock absorber along with the spring, then use a spring clamp to secure the spring; 2. After replacing the shock absorber, release the spring clamp and reinstall both components together.
18
1
Share

What is the method to distinguish Mercedes-Benz taillights?

Mercedes-Benz taillights can be distinguished as follows: the S-class taillights feature three horizontal bars, while the C-class and E-class taillights have two horizontal bars. The classification of car lights includes: 1. Headlights: Located at the front of the car, primarily for illumination and signaling; 2. Combination taillights: Positioned at the rear of the car, mainly for illumination and signaling; 3. Turn signals: Used to indicate left or right turns; 4. License plate lights: Primarily to illuminate the license plate, enabling identification of the vehicle's license plate at night. The maintenance methods for car lights are: 1. Check the seal of the headlights. If moisture enters the headlight, it will reduce the bulb's lifespan. Replace the sealing ring between the lens and reflector immediately if damaged; 2. Clean the bulbs. Use alcohol-soaked cotton swabs to remove dust and dirt from the bulbs. After cleaning, let them dry and avoid touching the bulbs with hands or cloth; 3. Clean the reflector. Use clean cotton dipped in hot water for cleaning, but do not scrub to avoid damaging the reflector's coating.
8
1
Share

What is the normal tire pressure for a Jeep Compass?

The standard tire pressure range for a Jeep Compass is 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and reduced by 0.1 bar in summer. This data is based on the international GBT2978-2008 standard. The Compass's tire pressure monitoring system is displayed on the dashboard. The system provides real-time automatic monitoring of tire pressure during driving and alerts the driver to tire leaks or low pressure to ensure driving safety. Generally, a tire pressure exceeding 2.8 bar is considered too high, while a tire pressure below 2.0 bar is considered too low. Hazards of overinflated tires: Reduced tire friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates wear on the central tread pattern, shortening tire lifespan; increases vehicle vibration, indirectly affecting the lifespan of other components; overstretches tire cords, reducing elasticity and increasing the load on the vehicle during driving. Hazards of underinflated tires: Increased friction coefficient with the road surface, leading to higher fuel consumption; makes the steering wheel heavy and prone to deviation, compromising driving safety; increases movement in various tire parts, causing abnormal heat due to excessive rolling; reduces the functionality of cords and rubber, leading to delamination or cord breakage and excessive friction with the rim, damaging the bead area and causing abnormal wear; multiplies friction between the tire and ground, sharply raising tire temperature, softening the tire, and drastically reducing strength. High-speed driving may result in a blowout. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no seal on top, four small spikes below, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure: Typically, an alarm is triggered if the pressure is below 1.8 bar or above 3.0 bar. In this case, the tires need to be checked and the pressure adjusted. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure monitoring system is not reset in time, it will continue to display the previous data, causing the indicator light to come on. Simply reset the tire pressure monitoring system to resolve this issue. Damaged tire pressure sensor: The tire pressure sensor, which monitors tire pressure, is installed inside the tire and connected to the inflation valve. If the sensor is damaged due to impact while driving, the tire pressure warning light will illuminate. For sensor damage, the only solution is to replace it with a new component.
6
0
Share

What engine does the Subaru BRZ use?

Subaru BRZ uses a 2.0-liter naturally aspirated engine with the code name FA20. This engine has a maximum horsepower of 200, a maximum power of 147 kilowatts, and a maximum torque of 205 Newton meters. The Subaru BRZ is a hardtop sports car produced by Subaru and is an imported model. The body dimensions of the Subaru BRZ are 4240 millimeters in length, 1775 millimeters in width, and 1285 millimeters in height, with a wheelbase of 2570 millimeters. The car adopts a front-engine, rear-wheel-drive layout, with a front MacPherson independent suspension and a rear double-wishbone suspension.
1
5
Share

What is the fuel consumption of the 3.5T Raptor?

The Raptor currently has one model on sale. The 2022 3.5T Raptor equipped with a 423-horsepower engine has an NEDC fuel consumption of 11.5L per 100 kilometers. Different Raptor models have varying fuel tank capacities. The distance that can be covered on a full tank of fuel is as follows: For the model equipped with a 423-horsepower engine, the fuel tank capacity is 136.3L. On a full tank, it can cover a distance of 136.3/11.5*100=1185KM. The fuel consumption of a car is directly influenced by five major factors: driving habits, the car itself, road conditions, natural wind, and environmental temperature. Specific factors that can increase fuel consumption include: Driving habits: Aggressive driving behaviors such as sudden acceleration, frequent overtaking, and not easing off the throttle before a red light can increase fuel consumption. The car itself: Cars with larger engine displacements generally consume more fuel than those with smaller displacements because larger displacements usually mean higher power output, requiring more gasoline for combustion. Heavier cars also consume more fuel due to the greater driving torque needed. Road conditions: Driving on unpaved roads, muddy roads, soft surfaces, or mountainous terrain increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases the car's resistance and fuel consumption. Low environmental temperatures: When the engine block is cold, the injected gasoline does not atomize easily, requiring more gasoline for combustion, which increases fuel consumption. Additionally, in cold temperatures, the engine's computer may control the engine to run at higher RPMs to warm up, further increasing fuel consumption.
17
3
Share

Is the Subaru BRZ a four-wheel drive?

Subaru BRZ is not a four-wheel drive; it adopts a front-engine, rear-wheel-drive system. The Subaru BRZ is equipped with a naturally aspirated engine with a displacement of 2.0 liters, codenamed FA20. The transmission options include a 6-speed manual and a 6-speed automatic. The engine delivers a maximum horsepower of 200 HP, a maximum power output of 147 kW, and a maximum torque of 205 Nm. The Subaru BRZ is a hardtop sports car produced by Subaru, with a body length of 4240mm, a width of 1775mm, and a height of 1320mm, aligning with its positioning as a 2-door, 4-seater hardtop sports car.
10
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.