Will Keeping Brake-Hold On Damage the Car?

1 Answers
MacKira
07/30/25 4:36am
Keeping brake-hold on will not damage the car, and this function can be used for a long time. Brake-hold is an automatic parking system, and the function of the automatic parking technology is to prevent the vehicle from rolling backward, which is especially suitable for uphill and downhill slopes and frequent starting and stopping. The specific content is introduced as follows: 1. The function of brake-hold: Brake-hold allows the driver to avoid unnecessary sliding of the vehicle without the need for prolonged braking or activating the electronic parking brake. In addition, this function can also prevent the vehicle from rolling backward when starting on a slope. Brake-hold automatic parking is a very practical function. 2. Points to note when using brake-hold: Brake-hold does no harm. The only thing worth noting is that after getting used to it, you should be careful when driving a car without this function after braking, and do not habitually take your foot off the brake.
Was this review help?
8
0
Share
More Forum Discussions

What are the reasons for the BYD S7 transmission failure?

BYD S7 transmission failure may be caused by the following reasons: 1. Transmission: The transmission warning light indicates an internal fault in the transmission. A diagnostic tool can be used to read the fault code, and then the fault point can be identified based on the code. 2. Components: Possible causes include faults in the transmission control module, shift solenoid valve, internal gear wear, or internal friction plates. 3. Note: Factors such as high temperature, lack of lubrication, debris, or incorrect shift software logic can trigger this warning light. Once the warning light comes on, it is recommended to visit a repair shop immediately, as any of these issues can lead to significant problems.
9
3
Share

What is China IV Emission Standard?

China's fourth-stage motor vehicle pollutant emission standard, abbreviated as "China IV Emission Standard." The main pollutants emitted by vehicles include HC, NOx, CO, PM, etc. Through the application of technologies such as the active layer of catalytic converters, secondary air injection, and exhaust gas recirculation systems with cooling devices, the standard aims to control and reduce vehicle emissions below specified limits. Below are the implementation timelines for the emission standards: 1. China I Standard: Nationwide implementation on July 1, 2001, primarily targeting restrictions on carbon monoxide, hydrocarbons, and particulate emissions. 2. China II Standard: Nationwide implementation on July 1, 2004, requiring a 30% reduction in carbon monoxide and a 55% reduction in hydrocarbons and carbon oxides. 3. China III Standard: Nationwide implementation on July 1, 2007, requiring a 40% reduction in total pollutant emissions compared to China II. 4. China IV Standard: Nationwide implementation on July 1, 2010, requiring a 50% to 60% reduction compared to China III. 5. China V Standard: Nationwide implementation on January 1, 2018, requiring a 25% reduction in nitrogen oxide emissions compared to China IV. 6. China VI Standard: China VIa nationwide implementation on July 1, 2020, and China VIb nationwide implementation on July 1, 2023.
6
2
Share

Why was the URV discontinued?

Because the URV could not meet the China VI emission standards. 1. Exterior: The URV features a new front fascia design catering to younger consumers, with extensive chrome accents and muscular lines enhancing its presence. In contrast, the Avancier's exterior design is more refined and sporty, with sharper angles and less softness. 2. Features: Equipped with premium amenities like leather seats, panoramic power sunroof, rearview camera, front fog lamps, etc. Additional high-end features include LED headlights, leather-wrapped steering wheel, heated front seats, panoramic power sunroof, front/rear curtain airbags, and rearview camera.
7
3
Share

Start the Engine First or Press the Clutch?

Press the clutch before starting the engine. Here are the relevant details: 1. Pressing the Clutch: It is advisable to press the clutch when starting the engine during the driving test (Subject 3), as the car may lurch forward if the gear is not in neutral. Additionally, if the test computer requires it, failing to press the clutch while starting the engine will result in points deduction. 2. Check: Before starting the engine, it's best to check whether the car's lights have been reset. If not, it might lead to failure in the light simulation test. Therefore, before starting the test, ensure the switch on the light control lever is in the OFF position.
11
4
Share

What is the motor power of the Range Rover Sport new energy model?

The motor power of the Range Rover Sport new energy model is 85KW. In terms of power, the Range Rover Sport new energy model is composed of a 2.0-liter inline 4-cylinder turbocharged engine and an electric motor, matched with an 8-speed automatic transmission. The Range Rover Sport new energy model is an SUV with a body size of 4879mm in length, 2073mm in width, and 1803mm in height, and a wheelbase of 2923mm. In terms of interior, the Range Rover Sport new energy model is designed with a full-color touch screen, providing integrated control for complete audio, calls, navigation, and information query.
3
5
Share

What is the reason why the car's P light keeps flashing and cannot start?

The reason why the car's P light keeps flashing and cannot start is due to electrical or mechanical faults; fuel system faults. There are 3 tips for driving an automatic transmission: 1. When waiting at a red light: Depending on driving habits, temporarily stop and hold the brake while in D gear because the torque converter inside the transmission is equipped with a reaction wheel with a one-way clutch, whose function is to amplify the torque from the engine crankshaft. It does not rotate at engine idle speed and only comes into play when the engine speed increases; 2. When starting: Press the brake pedal before moving the gear lever from P or N gear to the driving gear. Release the brake pedal, and the vehicle can slowly move. The purpose of pressing the brake in advance is to ensure the safety of the driver and the vehicle; 3. When starting the engine: The engine can only be started when the gear lever is in P or N position. If the gear lever is in driving gears such as D, R, etc., the engine cannot be started.
18
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.