Will hitting the transmission oil pan affect the transmission?

1 Answers
GageAnn
07/25/25 10:10am
Carefully check for oil leaks, as leaks will have an impact. Below is an introduction to oil leakage situations after the transmission is hit: 1. Check for external oil leaks: Pay special attention to whether there are oil leaks at the front and rear crankshaft oil seals. A cracked, damaged, or aged front crankshaft oil seal, or wear on the contact surface between the crankshaft pulley and the oil seal, can cause oil leakage at the front of the crankshaft. A cracked or damaged rear crankshaft oil seal or an excessively small oil return hole in the rear main bearing cap that obstructs oil return can cause oil leakage at the rear of the crankshaft. 2. Oil leaks at the front and rear oil seals: If oil seeps from multiple locations such as the front and rear cylinder head covers, front and rear valve tappet chambers, oil filter, and oil pan gasket, but no obvious leak source is found, check the crankcase ventilation system, clean the crankcase ventilation pipes, and inspect whether the PCV valve is malfunctioning due to carbon buildup and gumming. 3. Check the oil pressure: If oil continues to leak from the oil filter and some oil pipe connections after tightening, check whether the oil pressure is too high and whether the oil pressure relief valve is malfunctioning.
Was this review help?
15
5
Share
More Forum Discussions

How to Charge a Car Battery by Yourself?

The method to charge a car battery by yourself is: 1. Connect the positive terminal of the charger to the positive terminal of the car battery, and the negative terminal of the charger to the negative terminal of the battery; 2. Press the charging button to start charging. Precautions for charging the battery are: 1. If the battery voltage is 10% lower than the rated voltage, it will cause the battery to be undercharged; 2. Avoid water entering the battery during charging; 3. The battery should be charged directly without removing it, otherwise data may be lost. The maintenance methods for the battery are: 1. When the electrolyte is low, distilled water or a special replenishing fluid should be added; 2. During daily driving, frequently check whether the small holes on the battery cover are ventilated; 3. Check whether the positive and negative terminals of the battery are oxidized; 4. Check all parts of the circuit for aging or short circuits; 5. Turn off all electrical equipment when leaving the car.
16
1
Share

How many kilometers should the spark plugs of Changan CS35 be replaced?

Changan CS35 spark plugs should be replaced every 50,000 to 70,000 kilometers. The replacement steps are: 1. Prepare tools; 2. Unscrew the high-voltage wire terminal; 3. Remove the spark plug; 4. Install the new spark plug. The function of the spark plug is to introduce the high-voltage electricity generated by the ignition coil into the engine cylinder, generating a spark between the spark plug electrodes to ignite the air-fuel mixture, enabling the engine to operate. Taking the 2017 Changan CS35 as an example, it is a compact SUV with body dimensions of: length 4170mm, width 1810mm, height 1670mm, wheelbase of 2560mm, fuel tank capacity of 52 liters, and curb weight of 1270kg.
9
1
Share

What is the method for removing the rear seat of the Changan CS35?

The method for removing the rear seat of the Changan CS35 is: 1. Park the car in a safe location; 2. Enter the rear seat, locate and remove the plastic protective cover under the rear seat; 3. Use a wrench to unscrew the bolts under the plastic protective cover; 4. Remove the rear seat, and the disassembly is complete. Taking the 2017 Changan CS35 as an example, it is a compact SUV with body dimensions of: length 4170mm, width 1810mm, height 1670mm, and a wheelbase of 2560mm. The 2017 Changan CS35 features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.6L naturally aspirated engine, producing a maximum horsepower of 125PS, maximum power of 92kW, maximum torque of 160Nm, and is paired with a 5-speed manual transmission.
6
2
Share

What causes intermittent shaking in the Wuling Hongguang S?

The intermittent shaking in the Wuling Hongguang S is primarily caused by excessive carbon buildup in the throttle body. Excessive carbon deposits in the throttle body can affect the engine's air intake, leading to symptoms such as cold idle shaking, unstable idle, and difficulty starting the vehicle. Taking the 2020 Wuling Hongguang S as an example, it is a microvan with the following dimensions: length 4390mm, width 1660mm, height 1750mm, and a wheelbase of 2720mm. It has a fuel tank capacity of 50 liters and a curb weight of 1185kg. The 2020 Wuling Hongguang S features a MacPherson strut front suspension and a leaf spring rear suspension. It is equipped with a 1.2L naturally aspirated engine, delivering a maximum horsepower of 76PS, a maximum power output of 56kW, and a peak torque of 110Nm, paired with a 5-speed manual transmission.
7
3
Share

What is the difference between Volvo XC60 T4 and T5?

The differences between Volvo XC60 T4 and T5 are: 1. Different maximum horsepower: Volvo XC60 T4 has a maximum horsepower of 190ps; T5 has a maximum horsepower of 250ps. 2. Different maximum torque: Volvo XC60 T4 has a maximum torque of 300nm; T5 has a maximum torque of 350nm. 3. Different maximum power: Volvo XC60 T4 has a maximum power of 140kw; T5 has a maximum power of 184kw. 4. Different driving methods: Volvo XC60 T4 is front-wheel drive; T5 is four-wheel drive. 5. Different energy levels: Volvo XC60 T4 is 2.0t single turbo low power; T5 is 2.0t single turbo high power.
16
0
Share

What kind of glue should be used to fix a leaking radiator?

For a leaking radiator, AB glue should be used. AB glue is another name for a two-component adhesive that consists of a base glue and a hardener. The base glue must be mixed with the hardener to achieve the hardening effect. It is a type of room-temperature hardening adhesive and does not rely on temperature to harden. The reasons for a radiator leak are: 1. Damage to the rubber ball valve, resulting in poor sealing; 2. Aging of the rubber gasket at the drainage port under the ball valve, leading to poor sealing; 3. Loosening of the connection between the spherical float in the radiator and the water inlet switch; 4. Cracked water pipe; 5. Caused by emulsified engine oil; 6. The radiator cap is not tightly fastened; 7. Cracked radiator cooling tubes. The radiator, also known as a heat exchanger, is a key component in the automotive cooling system. Its function is to allow the coolant to absorb heat in the radiator, dissipate the heat when it flows to the heat exchanger, and then return to the radiator to circulate, achieving the effect of temperature regulation.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.