Will driving the wrong way at a roundabout entrance be captured by cameras?

What is the reason for the Peugeot 308 blower not working?

Peugeot 308 blower not working is generally due to a problem with the blower circuit, most commonly a burnt-out resistor. Below is an extended introduction: 1. Composition of the blower: The blower mainly consists of the following six parts: motor, air filter, blower body, air chamber, base (also serving as the oil tank), and oil drip nozzle. 2. Working principle of the blower: The blower operates by the eccentric rotation of the rotor inside the cylinder, causing the volume between the blades in the rotor slots to change, thereby sucking in, compressing, and expelling air. During operation, the pressure difference of the blower automatically delivers lubrication to the oil drip nozzle, which drips into the cylinder to reduce friction and noise, while also preventing gas backflow in the cylinder. This type of blower is also known as a sliding vane blower.

3

Share

Does idling with the AC on consume more fuel?

Idling with the AC on does consume more fuel. Running the AC while idling increases fuel consumption, and prolonged idling can accelerate carbon buildup. Over time, this may lead to symptoms such as engine shaking at idle, increased fuel consumption, and poor acceleration. Here are the details: Increased fuel consumption when idling with AC on: When the AC is on while idling, the engine not only needs to power the AC compressor but also maintain the normal operation of the power steering and brake booster pumps. The latter two functions are completely unnecessary when the vehicle is stationary, and keeping them running will increase fuel consumption. Idling with AC on accelerates carbon buildup: When a car remains idling with the AC on for an extended period, the vehicle's heat dissipation is poor, and the engine compartment temperature rises, causing the air-fuel mixture in the gasoline engine to become richer. This leads to uneven distribution of the air-fuel mixture in the intake manifold, preventing complete combustion of gasoline particles. As a result, large amounts of carbon monoxide are emitted, and carbon deposits form in the cylinders. Carbon buildup can disrupt the engine's air-fuel ratio, affecting not only fuel consumption and power output but also potentially causing engine damage.

4

0

Share

Is It Normal for Fuel Consumption to Increase After Maintenance?

It is normal for fuel consumption to increase after maintenance. Here are the specific reasons: 1. Increased oil viscosity: When using the same type of oil, the newly replaced oil will have higher viscosity compared to oil that has run for 10,000 kilometers. This naturally creates greater resistance, leading to slightly higher fuel consumption under the same road conditions and driving style. This situation usually diminishes after a few hundred kilometers of driving. 2. Replacement of brake pads: After installing new brake pads, the friction gap is relatively smaller, which means the resistance during braking is slightly greater, resulting in a slight increase in fuel consumption. This will normalize after the brake pads' break-in period. 3. Slightly overfilled oil: If the oil level is too high, the crankshaft in the oil requires more energy to rotate, increasing the engine's load and consequently raising fuel consumption.

11

1

Share

Is it okay to drive in first gear with the clutch pressed?

Driving in first gear with the clutch pressed is not advisable. The speed of a car depends on its own gravity and inertia. Once the braking system of the car fails, the direct consequence is that the driver loses control of the vehicle. Tips for driving in first gear: When braking in first gear, the correct method is to press the clutch. Since the speed is relatively slow in first gear, not pressing the clutch while braking can easily cause the vehicle to stall. For manual transmission vehicles, in low-speed situations like first gear, the best way to decelerate without stalling the engine is to press both the clutch and the brake simultaneously. Precautions for driving: Apply light braking over a long distance when approaching a red light. This is a common technique used by many drivers on the road, especially in urban areas with frequent traffic lights, to maintain a safe distance from the vehicle ahead. Use engine braking wisely when going downhill. Avoid pressing the clutch when descending a slope and rely on the engine's own braking force to control the speed.

1

4

Share

What are the symptoms after a sedan gets waterlogged?

Check the air filter to see if there are obvious signs of water ingress on the air filter and the lower housing of the air filter. Below is relevant information about vehicle wading: 1. Introduction to vehicle wading: As the name suggests, vehicle wading refers to driving a vehicle on low-lying, waterlogged roads, passing through water. This usually occurs during rainy weather in low-lying areas where poor drainage leads to water accumulation on the road. 2. Precautions for vehicle wading: Before wading, observe the road conditions carefully; during wading, maintain steady power; after wading, check the electrical system. If a car stalls in water, the main reason is usually water entering the exhaust pipe, and in some cases, electrical damage may also occur. Once a car stalls in water, do not attempt to restart it, as this may cause water to enter the intake manifold and damage the valves, or in severe cases, lead to engine failure. Instead, the car should be towed to a 4S shop immediately for professional handling.

17

0

Share

What lights to use when making a right turn at an intersection at night?

Quickly turn the high beams on and off a few times to signal that a vehicle is approaching. At the same time, the right turn signal should also be activated. Below is relevant information: 1. No traffic lights: Turn on the low beams. If passing through an intersection without traffic signal control, you should slow down and alternately flash the high and low beams as a signal. 2. No illumination: Under normal circumstances, only the low beams are needed for night driving. If you encounter a completely dark road ahead with no street lighting facilities, the high beams should be turned on. If you are about to meet another vehicle, switch to low beams in advance and wait until the meeting is over before deciding whether to turn the high beams back on based on the situation.

15

5

Share

Will driving the wrong way at a roundabout entrance be captured by cameras?

What is the reason for the Peugeot 308 blower not working?

Does idling with the AC on consume more fuel?

Is It Normal for Fuel Consumption to Increase After Maintenance?

Is it okay to drive in first gear with the clutch pressed?

What are the symptoms after a sedan gets waterlogged?

What lights to use when making a right turn at an intersection at night?

Is 4 Liters of Engine Oil Enough for Haval H6?

What is the difference between a C2E driver's license and a C2?

Where to Replace the Windshield?

Which country is the NIO EP9 originally from?