Will crossing the line at a traffic light intersection result in penalty points?

1 Answers
McKatherine
07/30/25 2:56am
Normally, crossing the solid white line at a traffic light intersection will result in a 3-point penalty if caught by electronic police or traffic officers on site. Here are some additional details: 1. Under special circumstances, lane changing over the line is allowed if it does not affect other vehicles, but evidence should be preserved to apply for administrative reconsideration to cancel the penalty later. 2. If a traffic accident occurs due to crossing the solid line at a traffic light, full responsibility may be taken depending on the situation. Additional information: At intersections without traffic lights, do not blindly proceed. If you think there are few vehicles at such intersections and you can pass quickly, once vehicles on the transverse lane also pass quickly, you may only realize it when you reach the middle of the road, which can easily lead to collisions and accidents.
Was this review help?
14
2
Share
More Forum Discussions

Working Principle of Disc Brakes?

During braking, hydraulic fluid is forced into the inner and outer wheel cylinders, causing the pistons to press the brake pads against the brake disc under hydraulic pressure, generating friction torque to achieve braking. This is the working principle of disc brakes. Disc brakes mainly come in two types: full disc and spot disc. In full disc brakes, both the stationary and rotating elements of the friction pair are disc-shaped, referred to as the stationary disc and rotating disc respectively. The entire working surface of the brake disc can simultaneously contact the friction pads. Spot disc brakes have their brake pads and actuation devices mounted in a caliper-shaped bracket that spans both sides of the brake disc, known as the brake caliper. Caliper disc brakes have strong heat dissipation capabilities and good thermal stability. Disc brakes are now widely used in passenger cars. Most cars use them on all wheels, while a few only use them as front wheel brakes, paired with drum brakes on the rear wheels.
19
3
Share

Reasons and Solutions for Engine Stalling During Hill Start in Subject 2

Reasons for engine stalling during hill start in Subject 2: 1. The clutch contact point is not raised sufficiently (clutch lifted too low); 2. Releasing the handbrake without giving throttle (when the vehicle's idle speed is too low to initiate movement), causing the car to roll back. Solutions for engine stalling during hill start in Subject 2: 1. Apply throttle during hill start; 2. Release the clutch slowly. Universal hill start method: 1. If using the semi-engaged clutch method to perform hill start, the student must coordinate the throttle, clutch, and brake properly, which can be challenging for students who have only practiced for a few days. 2. When stopping, press both the clutch and brake simultaneously. 3. When starting, press both the brake and clutch simultaneously.
15
2
Share

What Documents Are Required for Annual Vehicle Inspection?

Documents required for annual vehicle inspection are as follows: Bring the "Motor Vehicle Inspection Label Application Form" (obtained from the vehicle management office), the vehicle owner's motor vehicle driving license, the compulsory traffic insurance certificate (copy), and the vehicle and vessel tax payment or tax exemption certificate. For company-owned vehicles, additional documents of the agent are required, including the original driving license, copy of compulsory traffic insurance, Organization Code Certificate of the People's Republic of China (with fresh seal), power of attorney (with fresh seal), and a copy of the agent's ID card. Extension: For vehicles exempt from inspection for 6 years, although the vehicle does not require an annual inspection, the label must be collected. In this case, the vehicle owner needs to bring the driving license and copy of the compulsory traffic insurance certificate to the vehicle management office to collect the annual inspection label. No fees are required, and it can be done by queuing for processing.
4
3
Share

What causes the Jetta's R gear to not display the reverse camera interface?

Jetta's R gear not displaying the reverse camera interface may be caused by the following reasons: Damaged or obstructed camera: If the camera is damaged, the image cannot be transmitted to the computer, naturally preventing it from being displayed. It is recommended that the owner promptly seek repair and, if necessary, replace the camera. Poor wire connection: If the owner frequently drives on rough roads, the bumpy environment may cause internal wiring to loosen or detach. When the wiring has poor contact, the camera's image cannot be transmitted to the main unit. In this case, the wiring inside the center console needs to be inspected. Dead battery: When the car is turned off, prolonged use of lights or multimedia can drain the battery. If the battery is low or dead, the car's multimedia system will not function, and the reverse camera will disappear. In this situation, the battery needs to be recharged or replaced.
2
2
Share

How to Set the Lock Beep Sound for Honda Fit?

The method to set the lock beep sound for Honda Fit is: If the lock beep option is available in the vehicle computer, you can enable or disable it through this option; If it is not displayed in the vehicle computer, it can be activated via the bus, which requires visiting a 4S shop or repair shop for setup. Below is more information about the Honda Fit: 1. The Fit is a compact 5-door, 5-seat hatchback under GAC Honda, equipped with a CVT transmission and a top speed of 190 km/h. 2. The Fit uses a 1.5L L4 naturally aspirated engine, with a maximum horsepower of 131 PS and a maximum torque of 155 Nm. Its dimensions are 4109mm in length, 1694mm in width, and 1537mm in height, with a wheelbase of 2530mm.
15
0
Share

What Causes a Burning Smell When the Car Air Conditioner is On?

There are several reasons why a burning smell may occur when the car air conditioner is running: 1. If the smell is not like burning plastic, it could be due to dust on the heating pipe being roasted when the electric auxiliary heating is in use. This smell usually fades after a few uses. It is recommended to turn off the electric auxiliary heating and have an air conditioner technician clean the dust on and around the heating pipe. 2. If the smell resembles burning plastic, it might be caused by a blocked air vent, leading to heat buildup and melting of internal plastic components. First, check if the air vent is obstructed by testing the airflow with your hand. If the airflow is weak, it is advisable to open the air conditioner for inspection and remove any blockages. 3. The issue could also stem from aging wiring or abnormal heating elements in the air conditioner, causing excessive heat production. In this case, the air conditioner should be opened for inspection.
6
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.